Journal home Browse Most cited

Most cited

  • Select all
  • RESEARCH ARTICLE
    Ke Qiu, Xiaoyang Yu, Qian Li, Huan Li, Ning Kang, Shouxiang Lu
    SmartMat, 2024, 5(3): e1232. https://doi.org/10.1002/smm2.1232
    PDF

    Research and development of novel fluorine-free materials to replace fluorinated aqueous film-forming foam (AFFF) are crucial for improving pool fire suppression performance and protecting the environment. In this study, we report the thermo-responsive fluorine-free foam stabilized by triblock PEO–PPO–PEO copolymers (EO)100(PO)65(EO)100 for pool fire suppression. Small-angle X-ray scattering (SAXS) and reflected light interferometric techniques are conducted to study the molecular self-assembly in bulk and film thinning behavior, and the foaming kinetics of copolymer solution and thermophysical properties of the liquid foam are studied by dynamic surface tension and oscillatory rheology analysis. At room temperature, the amphipathic structure of PEO–PPO–PEO makes it possible to absorb at the air–liquid interface forming large-scale liquid foams containing the mobile films with a detergent state. Upon heating to the surface cooling temperature of burning oil, the mobile films can be actively switched into mechanically strong films with rigid surfaces. The in situ switching of the two interfacial states leads to the significant enhancement of the foam stability, especially under the dual defoaming effects of heat and oil. What's more, it is observed that the confinement of organized copolymer micelles in the Plateau borders and micellar self-layering in film confinement induce drainage delay of foam and film's stepwise thinning phenomenon, further increasing film thickness and enhancing the thermal stability of the foam. In standard fire-fighting tests, it is proved that the burnback performance exhibited by thermo-responsive copolymer foams is three times better than that for classical fluorine-free foams and almost 1.5 times higher than that for commercial AFFF.

  • RESEARCH ARTICLE
    Guoqun Zhang, Yuan Chen, Lulu Fu, Lifeng Zheng, Kun Fan, Chenyang Zhang, Jincheng Zou, Huichao Dai, Linnan Guan, Yueyue Cao, Minglei Mao, Jing Ma, Chengliang Wang
    SmartMat, 2024, 5(3): e1216. https://doi.org/10.1002/smm2.1216
    PDF

    Aqueous zinc-ion batteries (ZIBs) have attracted extensive interest for the next-generation batteries, which, however, are facing great challenges due to the poor reversibility of zinc (Zn) anodes and side reactions of water decomposition. Herein, we demonstrated a strategy that the solvation sheath of Zn ions could be facilely regulated by supramolecular coordination chemistry by adding small amounts of cyclodextrins (CDs) and, hence, inhibited the side reactions and side products, widened the electrochemical window, facilitated the homogenous deposition of Zn ions, refined the Zn grains, and enhanced the stability of Zn anodes. Importantly, we demonstrated that compared with α- and β-CD, the γ-CD showed the best regulation effect of the solvation sheath of Zn ions either at the same molar ratio or at the same mass concentration, which could be ascribed to their difference in supramolecular coordination chemistry and the strongest interaction of γ-CD with Zn ions. As a result, with γ-CD, the Zn//Zn symmetric cells showed ultrahigh stability with a cycling lifespan of over 2400 h at a current density of 1 mA/cm2. These results highlight the regulation of solvation sheath by supramolecular coordination chemistry for highly stable Zn anodes and pave a new way to realize high-performance ZIBs.

  • RESEARCH ARTICLE
    Yan Chen, Liangpeng Chen, Bowen Geng, Fan Chen, Yuan Yuan, Deling Li, Yi-Xuan Wang, Wang Jia, Wenping Hu
    SmartMat, 2024, 5(3): e1229. https://doi.org/10.1002/smm2.1229
    PDF

    Conductive polymer hydrogels have greatly improved the compatibility of electronic devices with biological tissues for human–machine interfacing. Hydrogels that possess low Young's modulus, low interfacial impedance, and high tensile properties facilitate high-quality signal transmission across dynamic biointerfaces. Direct incorporation of elastomers with conductive polymers may result in undesirable mechanical and/or electrical performance. Here, a covalent cross-linking network and an entanglement-driven network with conductive poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) have been combined. The triple-network conductive hydrogel shows high stretchability (with fracture strain up to 900%), low impedance (down to 91.2 Ω·cm2), and reversible adhesion. Importantly, ultra-low modulus (down to 6.3 kPa) and strain-insensitive electrical/electrochemical performance were achieved, which provides a guarantee for low current stimulation. The material design will contribute to the progression of soft and conformal bioelectronic devices, and pave the way to future implantable electronics.

  • RESEARCH ARTICLE
    Li Tao, Bowen Jiang, Sijie Ma, Yan Zhang, Yuanqiang Huang, Yueyi Pan, Weijun Kong, Jun Zhang, Guokun Ma, Houzhao Wan, Yong Ding, Paul J. Dyson, Mohammad Khaja Nazeeruddin, Hao Wang
    SmartMat, 2024, 5(3): e1233. https://doi.org/10.1002/smm2.1233
    PDF

    Hybrid perovskites have attracted enormous attention in the next generation resistive switching (RS) memristor for the artificial synapses, owing to their ambipolar charge transport, long diffusion length, and tunable visible bandgap. However, the variable switch, limited reproducibility, and poor endurance are the obstacles to the practical application of the perovskite memristors. Herein, we reported a multilevel RS nonvolatile memory based on a 3D trigonal HC(NH2)2PbI3 (α-FAPbI3) perovskite layer modified by 1-cyanobutyl-3-methylimidazolium chloride ([CNBmim]Cl) and sandwiched between ITO and Au electrodes (Au/[CNBmim]Cl/α-FAPbI3/SnO2/ITO). In contrast to the bare memristor with failure switching from low resistance state (LRS) to high resistance state (HRS), the memristor device based on the α-FAPbI3 modified with [CNBmim]Cl (Target device) shows the retention time over 104 s with On/Off ratio (>102) and endurance up to 550 cycles. The stable RS cycle benefits from the accelerated electrons de-trapping from the reduced defects and fast charge separation in the interface of α-FAPbI3/electrode, leading to the rupture of conductive filaments and transition of LRS to HRS. As a two-terminal analog synaptic device, the target device can realize random handwritten digit recognition with an impressive accuracy of 89.3% on the condition of low learning phases (500 training cycles).

  • RESEARCH ARTICLE
    Jiahui Huang, Xianwu Huang, Peiyi Wu
    SmartMat, 2024, 5(2): e1228. https://doi.org/10.1002/smm2.1228
    PDF

    Booming sophisticated robotics and prosthetics put forward high requirements on soft conductive materials that can bridge electronics and biology, those soft conductive materials should imitate the mechanical properties of biological tissues and build information transmission networks. Until now, it remains a great challenge to handle the trade-off among ease of preparation, high conductivity, processability, mechanical adaptability, and external stimuli responsiveness. Herein, a kind of readily prepared and processed multifunctional MXene nanocomposite hydrogel is reported, which is prepared via the fast gelation of cationic monomer initiated by delaminated MXene sheets. The gelation time can be adjusted (several seconds to minutes) based on the MXene loadings. By adjusting the MXene ratio, the resulting nanocomposites are ultrastretchable (>5000%), three-dimensional (3D) printable, and show outstanding mechanical and electrical self-healing. As expected, the integration of multifunctional systems onto various substrates (e.g., gloves and masks) is further demonstrated via 3D printing and could achieve diverse sensory capabilities toward strain, pressure, and temperature, showing great prospects as smart flexible electronics.

  • RESEARCH ARTICLE
    Dong Zhang, Yijing Tang, Xiong Gong, Yung Chang, Jie Zheng
    SmartMat, 2024, 5(2): e1160. https://doi.org/10.1002/smm2.1160
    PDF

    Development and understanding of highly mechanically robust and electronically conducting hydrogels are extremely important for ever-increasing energy-based applications. Conventional mixing/blending of conductive additives with hydrophilic polymer network prevents both high mechanical strength and electronic conductivity to be presented in polymer hydrogels. Here, we proposed a double-network (DN) engineering strategy to fabricate PVA/PPy DN hydrogels, consisting of a conductive PPy-PA network via in-situ ultrafast gelation and a tough PVA network via a subsequent freezing/thawing process. The resultant PVA/PPy hydrogels exhibited superior mechanical and electrochemical properties, including electrical conductivity of ~6.8 S/m, mechanical strength of ~0.39 MPa, and elastic moduli of ~0.1 MPa. Upon further transformation of PVA/PPy hydrogels into supercapacitors, they demonstrated a high capacitance of ~280.7 F/g and a cycle life of 2000 galvanostatic charge/discharge cycles with over 94.3% capacity retention at the current density of 2 mA/cm2 and even subzero temperatures of −20 °C. Such enhanced mechanical performance and electronic conductivity of hydrogels are mainly stemmed from a synergistic combination of continuous electrically conductive PPy-PA network and the two interpenetrating DN structure. This in-situ gelation strategy is applicable to the integration of ionic-/electrical-conductive materials into DN hydrogels for smart-soft electronics, beyond the most commonly used PEDOT:PSS-based hydrogels.

  • REVIEW
    Xuan Gao, Kejiang Liu, Chang Su, Wei Zhang, Yuhang Dai, Ivan P. Parkin, Claire J. Carmalt, Guanjie He
    SmartMat, 2024, 5(1): e1197. https://doi.org/10.1002/smm2.1197
    PDF

    Three-dimensional (3D) printing has the potential to revolutionize the way energy storage devices are designed and manufactured. In this paper, we explore the use of 3D printing in the design and production of energy storage devices, especially zinc-ion batteries (ZIBs) and examine its potential advantages over traditional manufacturing methods. 3D printing could significantly improve the customization of ZIBs, making it a promising strategy for the future of energy storage. In particular, 3D printing allows for the creation of complex, customized geometries, and designs that can optimize the energy density, power density, and overall performance of batteries. Simultaneously, we discuss and compare the impact of 3D printing design strategies based on different configurations of film, interdigitation, and framework on energy storage devices with a focus on ZIBs. Additionally, 3D printing enables the rapid prototyping and production of batteries, reducing leading times and costs compared with traditional manufacturing methods. However, there are also challenges and limitations to consider, such as the need for further development of suitable 3D printing materials and processes for energy storage applications.

  • COMMENT
    Junjun Li, Yajing Sun, Zhicheng Zhang
    SmartMat, 2024, 5(3): e1209. https://doi.org/10.1002/smm2.1209
    PDF

    Copper (Cu) has been regarded as a highly efficient electrocatalyst for the conversion of CO2 into a multicarbon product. However, the catalytic mechanism and the active sites of Cu catalysts under operating conditions still remain elusive. Yang's team applied systematic operando characterization techniques to provide a quantitative analysis of the valence states and the chemical environment of Cu nanocatalysts under electrochemical reaction conditions, which clearly reveal the evolution of Cu nanocatalysts before and after the entire electrochemical CO2 reduction.

  • RESEARCH ARTICLE
    Yang Ding, Jingjie Chen, Qiong Wu, Bin Fang, Wenhui Ji, Xin Li, Changmin Yu, Xuchun Wang, Xiamin Cheng, Hai-Dong Yu, Zhangjun Hu, Kajsa Uvdal, Peng Li, Lin Li, Wei Huang
    SmartMat, 2024, 5(3): e1214. https://doi.org/10.1002/smm2.1214
    PDF

    As one of the major causes of antimicrobial resistance, β-lactamase develops rapidly among bacteria. Detection of β-lactamase in an efficient and low-cost point-of-care testing (POCT) way is urgently needed. However, due to the volatile environmental factors, the quantitative measurement of current POCT is often inaccurate. Herein, we demonstrate an artificial intelligence (AI)-assisted mobile health system that consists of a paper-based β-lactamase fluorogenic probe analytical device and a smartphone-based AI cloud. An ultrafast broad-spectrum fluorogenic probe (B1) that could respond to β-lactamase within 20 s was first synthesized, and the detection limit was determined to be 0.13 nmol/L. Meanwhile, a three-dimensional microfluidic paper-based analytical device was fabricated for integration of B1. Also, a smartphone-based AI cloud was developed to correct errors automatically and output results intelligently. This smart system could calibrate the temperature and pH in the β-lactamase level detection in complex samples and mice infected with various bacteria, which shows the problem-solving ability in interdisciplinary research, and demonstrates potential clinical benefits.

  • RESEARCH ARTICLE
    Wei Lu, Ruijia Wang, Muqing Si, Yi Zhang, Shuangshuang Wu, Ning Zhu, Wenqin Wang, Tao Chen
    SmartMat, 2024, 5(2): e1190. https://doi.org/10.1002/smm2.1190
    PDF

    Biomimetic intelligent polymeric hydrogel actuators with cooperative fluorescence-color switchable behaviors are expected to find great potential applications in soft robotics, visual detection/display, and camouflage applications. However, it remains challenging to realize the spatial manipulation of synergistic shape/color-changing behaviors. Herein, we report an interfacial supramolecular assembly (ISA) approach that enables the construction of robust fluorescent polymeric hydrogel actuators with spatially anisotropic structures. On the basis of this ISA approach, diverse 2D/3D soft fluorescent hydrogel actuators, including chameleon- and octopi-shaped ones with spatially anisotropic structures, were facilely assembled from two different fluorescent hydrogel building blocks sharing the same physically cross-linked agar network. Spatially control over synergistic shape/color-changing behaviors was then realized in one single anisotropic hydrogel actuator. The proposed ISA approach is universal and expected to open promising avenues for developing powerful bioinspired intelligent soft actuators/robotics with selective spatial shape/color-changing behaviors.

  • REVIEW
    Qinghe Cao, Yong Gao, Jie Pu, Abdelnaby M. Elshahawy, Cao Guan
    SmartMat, 2024, 5(1): e1194. https://doi.org/10.1002/smm2.1194
    PDF

    Benefiting from the high capacity of Zn metal anodes and intrinsic safety of aqueous electrolytes, rechargeable Zn ion batteries (ZIBs) show promising application in the post-lithium-ion period, exhibiting good safety, low cost, and high energy density. However, its commercialization still faces problems with low Coulombic efficiency and unsatisfied cycling performance due to the poor Zn/Zn2+ reversibility that occurred on the Zn anode. To improve the stability of the Zn anode, optimizing the Zn deposition behavior is an efficient way, which can enhance the subsequent striping efficiency and limit the dendrite growth. The Zn deposition is a controlled kinetics-diffusion joint process that is affected by various factors, such as the interaction between Zn2+ ions and Zn anodes, ion concentration gradient, and current distribution. In this review, from an electrochemical perspective, we first overview the factors affecting the Zn deposition behavior and summarize the modification principles. Subsequently, strategies proposed for interfacial modification and 3D structural design as well as the corresponding mechanisms are summarized. Finally, the existing challenges, perspectives on further development direction, and outlook for practical applications of ZIBs are proposed.

  • RESEARCH ARTICLE
    Bojing Lu, Dunan Hu, Ruqi Yang, Jigang Du, Lingxiang Hu, Siqin Li, Fengzhi Wang, Jingyun Huang, Pingwei Liu, Fei Zhuge, Yu-Jia Zeng, Zhizhen Ye, Jianguo Lu
    SmartMat, 2024, 5(3): e1240. https://doi.org/10.1002/smm2.1240
    PDF

    Conductive-bridge random access memory (CBRAM) emerges as a promising candidate for next-generation memory and storage device. However, CBRAMs are prone to degenerate and fail during electrochemical metallization processes. To address this issue, herein we propose a self-repairability strategy for CBRAMs. Amorphous NbSe2 was designed as the resistive switching layer, with Cu and Au as the top and bottom electrodes, respectively. The NbSe2 CBRAMs demonstrate exceptional cycle-to-cycle and device-to-device uniformity, with forming-free and compliance current-free resistive switching characteristics, low-operation voltage, and competitive endurance and retention performance. Most importantly, the self-repairable behavior is discovered for the first time in CBRAM. The device after failure can recover its performance to the initially normal state by operating with a slightly large reset voltage. The existence of Cu conductive filament and excellent controllability of Cu migration in the NbSe2 switching layer has been revealed by a designed broken-down point approach, which is responsible for the self-repairable behavior of NbSe2 CBRAMs. Our self-repairable and high-uniform amorphous NbSe2 CBRAM may open the door to the development of memory and storage devices in the future.

  • RESEARCH ARTICLE
    Yingnan Han, Chang Yu, Hongling Huang, Qianbing Wei, Junting Dong, Lin Chen, Jieshan Qiu
    SmartMat, 2024, 5(1): e1206. https://doi.org/10.1002/smm2.1206
    PDF

    Electrocatalytic water splitting that is coupled with electrocatalytic chemical oxidation is considered as one of the promising methods for efficiently obtaining hydrogen energy and fine chemicals. Herein, we focus on an electrochemical redox activation strategy to rationally manipulate the microstructure and surface valence states of copper foam (CF) and boost the corresponding performance towards electrocatalytic benzyl alcohol oxidation (EBA), accompanied by the efficient hydrogen production. Correspondingly, the Cu(II)-dominated species are gradually formed on the CF surface with the dissolution and redeposition of copper in the suitable potential range. The new species containing Cu2O, CuO, and Cu(OH)2 during surface reconstruction process of the CF were confirmed by multiple characterization techniques. After 220-cycled activation (CF-220), the activated CF achieves an increase of current density for EBA in anode from 9.5 for the original CF to 29.3 mmol/cm2, while the pure hydrogen yield increases threefold than that of the original CF at 1.5 VRHE. The produced new species can endow the CF-220 with abundant acidity sites, which can enhance the adsorption toward Lewis-basicity benzyl alcohol, confirmed by NH3-temperature-programmed desorption. In situ Raman result further reveals that the as-produced CuO, Cu(OH)2, and Cu(OH)42− are the main active species toward the EBA process.

  • REVIEW
    Yafei Yang, Dong He, Xiaobo Feng, Xiangheng Xiao
    SmartMat, 2024, 5(3): e1223. https://doi.org/10.1002/smm2.1223
    PDF

    Covalent organic framework (COF) materials have aroused tremendous interest in photocatalytic applications due to their tunable pore structure and photoelectric properties. The regular nanopore of COF itself presents a strongly confinement effect, which provides a unique regulatory effect for photons, electrons, protons, and other quantum-scale reaction groups. However, due to the weak surface electron coupling and transfer ability between the reactive groups and basic elements of its structural units, the activity of pure COFs photocatalyst is still not satisfactory. Therefore, the confinement modification strategy of confining low-dimension entities within COFs has been proposed, thus realizing new active sites construction and band structure regulation has been intensively studied, but yet to be summarized systematically. In this paper, the semi-conductivity of COFs is discussed dialectically based on photocatalytic thermodynamics, and the influence of internal linkage motifs and stacking behaviors on the band structure is collected. Then, the basic understanding of confinement characteristics and their influence on photocatalytic performance in dynamics is further explained according to the spatial dimension classification of low-dimension entities. And the application and mechanism of these COF-based confined catalysts in energy conversion reactions are discussed in detail. Lastly, the current challenges and development prospects of COF-based confined hetero-photocatalysts are discussed.

  • RESEARCH ARTICLE
    Song Yang, Yanfei Ma, Chenxi Qin, Zhizhi Zhang, Jianqing Yu, Xiaowei Pei, Bo Yu, Wenbo Sheng, Feng Zhou, Weimin Liu
    SmartMat, 2024, 5(2): e1235. https://doi.org/10.1002/smm2.1235
    PDF

    Despite extensive efforts in designing and preparing switchable underwater adhesives, it is not easy to regulate the underwater adhesion strength locally and remotely. Here, we design and synthesize photoreversible copolymer of poly[dopamine methacrylamide-co-methoxyethyl-acrylate-co-7-(2-methacryloyloxyethoxy)-4-methylcoumarin]. Due to the dynamic formation and breaking of chemical crosslinking networks within the smart adhesives, the material shows widely tunable adhesion strength from ∼150 to ∼450 kPa and long-range reversible maneuverability under orthogonal 254 and 365 nm ultraviolet light stimulation via the coumarin dimerization and cycloreversion. Moreover, the adhesive exhibits good circulation performance and stability in an acid–base environment. It also demonstrated that the bolt can be coated with the smart adhesive material for on-demand bonding. This design principle opens the door to the development of remotely controllable high-performance smart underwater adhesives.

  • RESEARCH ARTICLE
    Guangli Li, Ying Liu, Yuwei Chen, Yonghui Xia, Xiaoman Qi, Xuan Wan, Yuan Jin, Jun Liu, Quanguo He, Kanghua Li, Jianxin Tang
    SmartMat, 2024, 5(2): e1173. https://doi.org/10.1002/smm2.1173
    PDF

    Herein, we fabricated a flexible semidry electrode with excellent mechanical performance, satisfactory self-adhesiveness, and low-contact impedance using physical/chemical crosslinked polyvinyl alcohol/polyacrylamide dual-network hydrogels (PVA/PAM DNHs) as an efficient saline reservoir. The resultant PVA/PAM DNHs showed admirable adhesive and compliance to the hairy scalp, facilitating the establishment of a robust electrode/skin interface for biopotential signal transmission. Moreover, the PVA/PAM DNHs steadily released trace saline onto the scalp to achieve the minimized potential drift (1.47 ± 0.39 mV/min) and low electrode–scalp impedance (18.2 ± 8.9 kΩ @ 10 Hz). More importantly, the application feasibility of real-world brain−computer interfaces (BCIs) was preliminarily validated by 10 participants using two classic BCI paradigms. The mean temporal cross-correlation coefficients between the semidry and wet electrodes in the eyes open/closed and the N200 speller paradigms are 0.919 ± 0.054 and 0.912 ± 0.050, respectively. Both electrodes demonstrate anticipated neuroelectrophysiological responses with similar patterns. This semidry electrode could also effectively capture robust P-QRS-T peaks during electrocardiogram recording. Considering their outstanding advantages of fast setup, user-friendliness, and robust signals, the proposed PVA/PAM DNH-based electrode is a promising alternative to wet electrodes in biopotential signal acquisition.

  • RESEARCH ARTICLE
    Ziqing Hu, Hanwei Zhang, Hui Liu, Jinsa Li, Xiaofan Ji, Ben Zhong Tang
    SmartMat, 2024, 5(2): e1184. https://doi.org/10.1002/smm2.1184
    PDF

    Traditional multicolor fluorescent hydrogels are generated through the assembly of discrete fluorescent hydrogels, which is not a complete integration much distinct from living organisms. On the basis of aggregation-induced emission (AIE), a special solvent polar-responsive AIE molecule possessing a twisted intramolecular charge transfer (TICT) effect was noticed. By incorporating it into the gel network, an AIE gel that displays continuous gradient fluorescence was fabricated. First, hydrogel A containing the solvent polar-responsive AIE-gen was prepared to show orange fluorescence. After soaking in the organic solvents, the fluorescence color transition of hydrogel A ranging from orange to green occurred when being immersed in high-polarity organic solvents ascribed to the embedded AIE-gen owning TICT effect. Then, hydrogel A was successively lifted up from organic solvents. Due to the different immersion time of each section for the hydrogel, the polarity difference occurred. Then, the produced gel B showed continuous gradient fluorescence ranging from orange to green under the irradiation of UV light.

  • RESEARCH ARTICLE
    Yushan Yang, Kaicong Chen, Yipeng Chen, Chao Wang, Baokang Dang, Yingying Li, Ming Liu, Qingfeng Sun
    SmartMat, 2024, 5(1): e1207. https://doi.org/10.1002/smm2.1207
    PDF

    Combination of flexible multifunctional stealth technology properties such as electromagnetic (EM) and infrared (IR) stealth is crucial to the development of aerospace, military, and electronic fields, but the synthesis technology still has a significant challenge. Herein, we have successfully designed and synthesized highly flexible MXene@cellulose lamellae/borate ion (MXCB) sheets with strong high-temperature EM-IR bi-stealth through sequential bridging of hydrogen and covalent bonds. The resultant MXCB sheets display high conductivity and good mechanical features such as flexibility, stretchability, fatigue resistance, and ultrasonic damage. MXCB sheets have a high tensile strength of 795 MPa. Furthermore, MXCB sheets with different thicknesses indicate exceptional high-temperature thermal-camouflage characteristics. This reduces the radiation temperature of the target object (>300 °C) to 100 °C. The conductivity of MXCB sheet with 3 μm thickness is 6108 S/cm and the EM interference (EMI) shielding value is 39.74 dB. The normalized surface-specific EMI SE absolute shielding effectiveness (SSE/t) is as high as 39312.78 dB·cm2/g, which remained 99.39% even after 10,000 times repeated folding. These multifunctional ultrathin MXCB sheets can be arranged by vacuum-assisted induction to develop EM-IR bi-stealth sheet.

  • RESEARCH ARTICLE
    Tiantian Yang, Chuanqi Cheng, Liyang Xiao, Min Wang, Feifei Zhang, Jiaqi Wang, Pengfei Yin, Gurong Shen, Jing Yang, Cunku Dong, Hui Liu, Xiwen Du
    SmartMat, 2024, 5(3): e1204. https://doi.org/10.1002/smm2.1204
    PDF

    Alloying is regarded as one of the most promising strategies for boosting performance of catalysts for hydrogen evolution reaction (HER) due to the adjustable electronic structure and intermediate adsorption. However, there is no theory (including d-band center theory) can accurately guide the preparation and design of alloy catalysts, and thus resulting all the reported alloy catalysts are obtained by time-consuming and laborious experimental exploration. Herein, we proposed a mean d-band center (εas) as a new accurate descriptor for alloy activity prediction. Theoretical simulation and experiment results revealed that this descriptor exhibits a strong scaling relation with H adsorption energy. Besides, the obtained Cu–Ag alloy displays an optimal overpotential of 223 mV at 10 mA/cm2 in 0.5 mol/L H2SO4, which is more than 300 mV lower than those of pristine Cu (530 mV) and Ag (569 mV) powder. Our work provides a new idea toward designing highly efficient HER catalysts and broadens the applicability of d-band theory to activity prediction of alloys.

  • REVIEW
    Khai J. Wong, Joel J. Foo, Tan J. Siang, Wee-Jun Ong
    SmartMat, 2024, 5(3): e1238. https://doi.org/10.1002/smm2.1238
    PDF

    Transition metal carbides, including both MXene and non-MXene metal carbides, have enjoyed a soaring reputation in recent years. Benefitting from their intriguing physical and chemical characteristics, they shine in multifarious research fields and currently, they have emerged as promising nanomaterials for photocatalysis in energy and environmental science. Herein, based on the recent theoretical research and experimental studies, a systematic and comprehensive review of the expeditious advances of metal carbides and their nano-architectures in the flourishing arena of photocatalysis is presented. The fundamental mechanism involved in photocatalysis with metal carbides serving as semiconductors or cocatalysts is thoroughly discussed. Besides, we highlight the main synthetic strategies of MXene and non-MXene metal carbides and unravel the structural properties of the as-obtained metal carbides via different fabrication routes to establish and elucidate their intriguing role in ameliorating photocatalytic activity. Moreover, the state-of-the-art advancements of metal carbides in diverse photocatalytic applications, including hydrogen evolution reaction, oxygen evolution reaction, overall water splitting, and carbon dioxide reduction reaction, are summarized. In particular, insights into the structure–activity relationship of metal carbide in photocatalysis are elucidated. Finally, this review concludes with the ongoing challenges and perspectives on the future directions of metal carbides in the realm of photocatalysis.

  • RESEARCH ARTICLE
    Gulzada Beket, Anton Zubayer, Qilun Zhang, Jochen Stahn, Fredrik Eriksson, Mats Fahlman, Thomas Österberg, Jonas Bergqvist, Feng Gao
    SmartMat, 2024, 5(3): e1237. https://doi.org/10.1002/smm2.1237
    PDF

    Harvesting indoor light to power electronic devices for the Internet of Things has become an application scenario for emerging photovoltaics, especially utilizing organic photovoltaics (OPVs). Combined liquid- and solid-state processing, such as printing and lamination used in industry for developing indoor OPVs, also provides a new opportunity to investigate the device structure, which is otherwise hardly possible based on the conventional approach due to solvent orthogonality. This study investigates the impact of fullerene-based acceptor interlayer on the performance of conjugated polymer–fullerene-based laminated OPVs for indoor applications. We observe open-circuit voltage (VOC) loss across the interface despite this arrangement being presumed to be ideal for optimal device performance. Incorporating insulating organic components such as polyethyleneimine (PEI) or polystyrene (PS) into fullerene interlayers decreases the work function of the cathode, leading to better energy level alignment with the active layer (AL) and reducing the VOC loss across the interface. Neutron reflectivity studies further uncover two different mechanisms behind the VOC increase upon the incorporation of these insulating organic components. The self-organized PEI layer could hinder the transfer of holes from the AL to the acceptor interlayer, while the gradient distribution of the PS-incorporated fullerene interlayer eliminates the thermalization losses. This work highlights the importance of structural dynamics near the extraction interfaces in OPVs and provides experimental demonstrations of interface investigation between solution-processed cathodic fullerene layer and bulk heterojunction AL.

  • RESEARCH ARTICLE
    Yifan Zhang, Shengqi Dai, Zeyu Yin, Weiqing Yan, Qian Li, Heng Yuan, Xu Zhang, Lin Chen, Jun Luo, Xiao Ouyang, Bin Liao, Wei Hao, Jia Zhu
    SmartMat, 2024, 5(3): e1225. https://doi.org/10.1002/smm2.1225
    PDF

    Polyimides externally deployed in spacecraft or satellites extensively have various aerospace hazards, including atomic oxygen (AO) erosion, irradiation degradation, and electrostatic charge/discharge (ESC/ESD). To cope with these challenges, we fabricate a ZnO/CuNi-polyimide composite film with augmented permanence. Using spectroscopy and microscopy techniques, we have shown that the combination of chelation and cross-linking in the interfacial architecture leads to enhanced interfacial compatibility and mechanical robustness. Besides, due to the positive AO diffusion barrier ability of the wurtzite ZnO, our composite film shows remarkable AO resistance and a very small Ey value of 6.88 × 10−26 cm3/atom, which is merely 2.29% of that of pristine polyimide. Moreover, the well-defined nanocrystalline state with minimal lattice swelling (0.3%–0.7%) of the Fe+-irradiated ZnO/CuNi-polyimide at a damaging dose of 353.4 dpa demonstrates its excellent irradiation resistance. Finally, the ZnO/CuNi-polyimide also shows sufficient electrostatic dissipation capacity to cope with the ESC/ESD events. Our fabrication approach for composite films based on multi-technology integration shows potential for aerospace applications and deployment.

  • RESEARCH ARTICLE
    Yajun Ding, Yuanchao Huang, Yuejiao Li, Tao Zhang, Zhong-Shuai Wu
    SmartMat, 2024, 5(1): e1150. https://doi.org/10.1002/smm2.1150
    PDF

    The realization of high-efficiency, reversible, stable, and safe Li-O2 batteries is severely hindered by the large overpotential and side reactions, especially at high rate conditions. Therefore, rational design of cathode catalysts with high activity and stability is crucial to overcome the terrible issues at high current density. Herein, we report a surface engineering strategy to adjust the surface electron structure of boron (B)-doped PtNi nanoalloy on carbon nanotubes (PtNiB@CNTs) as an efficient bifunctional cathodic catalyst for high-rate and long-life Li-O2 batteries. Notably, the Li-O2 batteries assembled with as-prepared PtNiB@CNT catalyst exhibit ultrahigh discharge capacity of 20510 mA·h/g and extremely low overpotential of 0.48 V at a high current density of 1000 mA/g, both of which outperform the most reported Pt-based catalysts recently. Meanwhile, our Li-O2 batteries offer excellent rate capability and ultra-long cycling life of up to 210 cycles at 1000 mA/g under a fixed capacity of 1000 mA·h/g, which is two times longer than those of Pt@CNTs and PtNi@CNTs. Furthermore, it is revealed that surface engineering of PtNi nanoalloy via B doping can efficiently tailor the electron structure of nanoalloy and optimize the adsorption of oxygen species, consequently delivering excellent Li-O2 battery performance. Therefore, this strategy of regulating the nanoalloy by doping nonmetallic elements will pave an avenue for the design of high-performance catalysts for metal-oxygen batteries.

  • RESEARCH ARTICLE
    Li Zhao, Jiawen Xu, Yao Tong, Pengyu Gong, Fucheng Gao, Hui Li, Yanyan Jiang
    SmartMat, 2024, 5(2): e1148. https://doi.org/10.1002/smm2.1148
    PDF

    The combination of the first-line standard chemotherapeutic drug doxorubicin hydrochloride (DOX) and the molecular-targeted drug Herceptin (HCT) has emerged as a promising strategy for human epidermal growth receptor 2 (HER-2) overexpressing breast cancer treatment. However, insufficient drug accumulation and severe cardiotoxicity are two major challenges that limit its clinical application. Herein, an in situ forming gold nanorods (AuNRs)-sodium alginate (ALG) hybrid hydrogel encapsulating DOX and HCT was engineered for tumor synergistic therapy involving injectable, dual-stimuli-responsive drug release, photothermal ablation, and drug-antibody synergistic therapy. The photothermal agent AuNRs, anticancer drug DOX, and anticancer antibody HCT were mixed in ALG solution, and after injection, the soluble ALG was quickly transformed into a hydrogel in the presence of Ca2+ in the body. Significantly, the hybrid hydrogel exhibits an extremely high photothermal conversion efficiency of 70% under 808 nm laser irradiation. The thermal effect can also provide photothermal stimulation to trigger the drug release from the gel matrix. In addition, the drug release rate and the releasing degree are also sensitive to the pH. In vitro studies demonstrated that the PEI-AuNR/DOX/HCT/ALG hydrogel has facilitated the therapeutic efficiency of each payload and demonstrated a strong synergistic killing effect on SK-BR-3 cells. In vivo imaging results showed that the local drug delivery system can effectively reduce the nonspecific distribution in normal tissues and increase drug concentration at tumor sites. The proposed hydrogel system shows significant clinical implications by easily introducing a sustainable photothermal therapy and a potential universal carrier for the local delivery of multiple drugs to overcome the challenges faced in HER-2 overexpressing cancer therapy.

  • RESEARCH ARTICLE
    Zongxiao Wu, Junlei Qi, Wenbin Wang, Peng Yang, Chen Ma, Haoxin Huang, Kai Bao, Jingkun Wu, Chengxuan Ke, Ye Chen, Chaoliang Tan, D. V. Maheswar Repaka, Qiyuan He
    SmartMat, 2024, 5(3): e1234. https://doi.org/10.1002/smm2.1234
    PDF

    The remarkable successes of graphene have sparked increasing interest in elemental two-dimensional (2D) materials, also referred to as Xenes. Due to their chemical simplicity and appealing physiochemical properties, Xenes have shown particular potential for numerous (opto) electronic, iontronic, and energy applications. Among them, layered α-phase tellurene has demonstrated the most promise, thanks to the recent successes in the chemical synthesis of highly crystalline 2D tellurene. However, the general electronic and electrochemical properties of tellurene in electrolyte systems remain ambiguous, hindering their further development. In this work, we studied the electrostatic gating, electrocatalysis, and electrochemical stability of tellurene in electrolyte systems. Our results show that tellurene obtained from both hydrothermal and chemical vapor deposition methods, two mainstream synthetic approaches for Xenes, demonstrates thickness-dependent ambipolar transport with high hole mobility and stability in both aqueous electrolytes and ionic liquids. More importantly, the electrochemical properties of tellurene are investigated via the emerging on-chip electrochemistry. Pristine tellurene demonstrates hydrogen evolution reaction with low Tafel slopes and remarkable electrochemical stability in acidic electrolytes over a large potential window. Our study provides a comprehensive understanding of the iontronic and electrochemical properties of tellurene, paving the way for the broad adoption of Xenes in sensors, synaptic devices, and electrocatalysis.

  • REVIEW
    Yue Guo, Hanmei Jiang, Binbin Liu, Xingyang Wang, Yifu Zhang, Jianguo Sun, John Wang
    SmartMat, 2024, 5(1): e1231. https://doi.org/10.1002/smm2.1231
    PDF

    Aqueous zinc-ion batteries (ZIBs) are regarded as among the most promising candidates for large-scale grid energy storage, owing to their high safety, low costs, and environmental friendliness. Over the past decade, vanadium oxides, which are exemplified by V2O5, have been widely developed as a class of cathode materials for ZIBs, where the relatively high theoretical capacity and structural stability are among the main considerations. However, there are considerable challenges in the construction of vanadium-based ZIBs with high capacity, long lifespan, and excellent rate performance. Simple widenings of the interlayer spacing in the layered vanadium oxides by pre-intercalations appear to have reached their limitations in improving the energy density and other key performance parameters of ZIBs, although various metal ions (Na+, Ca2+, and Al3+) and even organic cations/groups have been explored. Herein, we discuss the advances made more recently, and also the challenges faced by the high-performance vanadium oxides (V2O5-based) cathodes, where there are several strategies to improve their electrochemical performance ranging from the new structural designs down to sub-nano-scopic/molecular/atomic levels, including cation pre-intercalation, structural water optimization, and defect engineering, to macroscopic structural modifications. The key principles for an optimal structural design of the V2O5-based cathode materials for high energy density and fast-charging aqueous ZIBs are examined, aiming at paving the way for developing energy storage designed for those large scales, high safety, and low-cost systems.