Durability of plasma-sprayed Cr₃C₂-NiCr coatings under rolling contact conditions

Abstract

The aim of this paper was to address the rolling contact fatigue (RCF) failure mechanisms of plasma-sprayed Cr3C2-NiCr coatings under different tribological conditions of contact stress. Weibull distribution plots of fatigue lives of the coated specimens at different contact stresses were obtained. The failure modes of coatings were identified on the basis of wore surface observations of the failed coatings. Results showed that the RCF failure modes can be classified into four main categories, i.e., surface abrasion, spalling, cohesive delamination, and interfacial delamination. The probabilities of the surface abrasion and spalling type failures were relatively high at low contact stress. When the coatings were subjected to abrasion and spalling type failures, the failure of the coating was depended on the microstrcture of the coating. The stress concentration near the micro-defects in the coating may be the may reason for the formation of spall. The coatings were prone to fail in delamination under higher contact stresses. However, the delamination of coating may be related to distribution of shear stress amplitude within coating. The location of maximum shear stress amplitude can be used as a key parameter to predict the initiation of subsurface cracks within coating in rolling contact.

Keywords

rolling contact fatigue / coating / Weibull distribution / failure mode / mechanism

References

[1] Nieminen R, Vuoristo P, Niemi K, Mäntylä T, Barbezat G. Rolling contact fatigue failure mechanisms in plasma and HVOF sprayed WC-Co coatings. Wear, 1997, 212(1): 66–77

[2] Miller G R, Keer L M, Cheng H S. On the mechanics of fatigue crack growth due to contact loading. P Roy Soc Lond: Mat, 1813, 1985(397): 197–209

[3] Rosado L, Jain V K, Trived H K. The effect of diamond-like carbon coatings on the rolling fatigue and wear of M50 steel. Wear, 1997, 212(1): 1–6

[4] Ahmed R, Hadfield M. Rolling contact fatigue behaviour of thermally sprayed rolling elements. Surface and Coatings Technology, 1996, 82(1–2): 176–186

[5] Stewart S, Ahmed R. Contact fatigue failure modes in hot isostatically pressed WC-12%Co coatings. Surface and Coatings Technology, 2003, 172(2–3): 204–216

[6] Makela A, Vuroisto P, Lahdensuo M, Niemi K, Mantyla T. Rolling contact fatigue testing of thermally sprayed coatings. International Journal of Fatigue, 1995, 17: 305

[7] Ahmed R. Contact fatigue failure modes of HVOF coatings. Wear, 2003, 253(3–4): 473–487

[8] Nakajima A, Mawatari T, Yoshida M, Tani K, Nakahira A. Effects of coating thickness and slip ratio on durability of thermally sprayed WC cermet coating in rolling/sliding contact. Wear, 2000, 241(2): 166–173

[9] Ahmed R, Hadfield M. Experimental measurement of the residual stress field within thermally sprayed rolling elements. Wear, 1997, 209(1–2): 84–95

[10] Ahmed R, Hadfield M. Wear of high-velocity oxy-fuel (HVOF)-coated cones in rolling contact. Wear, 1997, 203–204: 98–106

[11] Nuruzzaman D M, Nakajima A, Mawatari T. Effects of substrate surface finish and substrate material on durability of thermally sprayed WC cermet coating in rolling with sliding contact. Tribology International, 2006, 39(7): 678–685

[12] Ahmed R, Hadfield M. Failure modes of plasma sprayed WC-15%Co coated rolling elements. Wear, 1999, 230(1): 39–55

[13] Shen X Y, Yu S Y. Performance in resistance to surface fatigue for Cr₃C₂-25%NiCr coatings by plasma spray and CDS spray. Tribology Letters, 2004, 16(3): 173–180

[14] Ahmed R, Hadfield M. Rolling contact fatigue performance of plasma sprayed coatings. Wear, 1998, 220(1): 80–91

[15] Sarma B Y, Mayuram M M. Some studies on life prediction of thermal sprayed coatings under rolling contact conditions. ASME J Tribol, 2000, 122(3): 503–510

[16] Ahmed R, Hadfield M. Rolling contact fatigue performance of detonation gun coated elements. Tribology International, 1997, 30(2): 129–137

[17] Tobe S, Kodama S, Misawa H. Rolling contact behaviour of plasma sprayed coating on aluminium alloy. In: Proc Nat Thermal Spray Conf. Tokyo, Japan, ASM international, Anaheim, CA, 1990: 171–178

[18] Berger L M, Vuoristo P, Mantyla T, Gruner W. Study of oxidation behavior of WC-Co, Cr₃C₂-NiCr and Tic-Ni-based materials in thermal spray processes. In: Coddet C, eds. Proceedings of the 15th International Thermal Spray Conference. Nice, France, 1998: 75–82

[19] Hertz H. Überdie Berührung fester elastischer Körper. J Reine Angew Math, 1881, 92: 156–171

[20] Johnson K L. Contact Mechanics. Cambridge: Cambridge University Press, 1992

[21] Shimizu S. P-S-N/P-F-L curve approach using three-parameter Weibull distribution for life and fatigue analysis of structural and rolling contact components. Tribol Trans, 2005, 48(4): 576–582

[22] Robert B A, Breneman J E, Medlin C H, Reinman G L. Weibull analysis handbook, US Air Force AFWAL-TR-83–2079, prepared for the Aero Propulsion and Power Laboratory, Wright-Patterson AFB, Ohio, 1983

[23] Kuroda S, Clyne T W. Quenching stress in thermally sprayed coatings. Thin Solid Films, 1991, 200(1): 49–66

[24] Kato K, Hokkirigawa K. Abrasive wear diagram. In: Proceedings of the Eurotrib’85. Amsterdam: Elsevier, 1985: 9–12

[25] Holmberg K, Matthews A, Ronkainen H. Coatings tribology-contact mechanisms and surface design. Tribology International, 1998, 31(1–3): 107–120

[26] Tallian T. Failure Atlas for Hertz Contact Machine Elements. New York: ASME Press, 1992

[27] Stewart S, Ahmed R, Itsukaichi T. Rolling contact fatigue of post-treated WC- NiCrBSi thermal spray coatings. Surface and Coatings Technology, 2005, 190(2–3): 171–189

[28] Liang G Y, Su J Y. The microstructure and tribological characteristics of laser-clad Ni-Cr-Al coatings on aluminium alloy. Materials Science and Engineering, 2000, A290: 207–212

[29] Miyashita Y, Yoshimura Y, Xu J Q, Horikoshi M, Mutoh Y. Subsurface crack propagation in rolling contact fatigue of sintered alloy. JSME International Journal, 2003, 46(3): 341–347

[30] Lundberg G, Palmgren A. Dynamic capacity of rolling bearings. Acta Polytechnica-Mech. Eng Series, 1947, 1: 4–51

[31] Fellows L, Nowell D, Hills D. On the initiation of fretting fatigue cracks. Wear, 1997, 205(1–2): 120–129

Acknowledgements

The authors are grateful for the support by the National Natural Science Foundations of China (Grant Nos. 50835003 and 50805047) and Shanghai Leading academic discipline project (B503). The author X C Zhang is also grateful for the support by the Shanghai Chenguang Planning Project (2008CG36), Shanghai Rising-Star Program (08QA14023) and Doctoral Fund of Ministry of Education of China (20090074120006).

RIGHTS & PERMISSIONS

2014 Higher Education Press and Springer-Verlag Berlin Heidelberg