Stability performance of buckling-restrained brace with brace joints

Abstract

The stability and ductility of four buckling-restrained braces (BRBs) with brace joints were studied. The load-carrying element of BRB was fabricated with steel (Chinese Q235), and a layer of colloidal silica sheet (0.5 mm in thickness) or four layers of plastic film (0.2 mm in thickness) were used as unbonding materials to provide space to prevent the buckling of inner core in higher modes and facilitate its lateral expansion in case of compression. Based on the equation of BRBs with brace joints of different restrained stiffnesses, the buckling load is calculated considering the initial geometric imperfections and residual stress, and the theoretical values agree well with the experiment results. It is concluded that the buckling load and ductility of BRBs are influenced greatly by the restrained stiffness of brace joints. If the restrained stiffness is deficient, the unstrained segment of BRBs with less stiffness will buckle firstly. As a result, the ultimate load of BRBs decreases, and the maximum compression load is reduced to about 65% of the maximum tension load; the stiffness also degenerates, and there is a long decreasing stage on the back-bone curve in compression phase; the ductility decreases, i.e., the ultimate tension ductility and ultimate compression ductility are approximately 15 and 1.3 respectively, and the cumulative plastic ductility is only approximately 200. If the restrained stiffness of joint is large enough, the stability will be improved as follows: the yielding strength and ultimate strength of BRBs are nearly the same, and there is an obvious strain intensification in both tension and compression phases; the ductility of brace also increases obviously, i.e., the ultimate tension ductility and ultimate compression ductility are both approximately 14, and the cumulative plastic ductility reaches 782.

Keywords

buckling-restrained braces / joint ends restrained stiffness / buckling load / stability performance / ductility

References

[1] Jia M., Zhang Sumei. Analysis of hysteretic behavior of buckling-restrained brace[J]. Journal of Tianjin University, 2008, 41(6): 736 744

[2] Xie Qiang. State of the art of buckling-restrained braces in Asia[J]. Journal of Constructional Steel Research, 2005, 61(6): 727-748.

[3] Sabelli R., Mahin S., Chang C. Seismic demands on steel braced frame buildings with buckling-restrained braces[J]. Engineering Structures, 2003, 25(5): 655-666.

[4] Black C., Makris N., Aiken Ian. Component testing, seismic evaluation and characterization of buckling-restrained braces[J]. Journal of Structural Engineering, ASCE, 2004, 130(6): 880-894.

[5] Cameron B., Nicos M., Aiken Ian. Component Testing, Stability Analysis and Characterization of Buckling-Restrained Unbonded Braces [R]. 2002, Berkeley: Pacific Earthquake Engineering Research Center, College of Engineering University of California.

[6] Tetsu Usami, Hirofumi Kaneko. Strength of H-shape braces constrained flexural buckling having unconstrained area at both ends(both ends simply supported) [J]. Journal of Constructional Engineering, AIJ, 2001 (542): 171–177 (in Japanese).

[7] Tetsu Usami, Hirofumi Kaneko, Tetsuro Ono. Strength of H-shape braces constrained flexural buckling having unconstrained area at both ends (both ends fixed) [J]. Journal of Constructional Engineering, AIJ, 2002 (558): 211–218 (in Japanese).

[8] Tembata Hideaki, Koetaka Yuji, Inoue Kazuo. Out-ofplane buckling load of buckling-restrained braces including brace joints [J]. Journal of Constructional Engineering, AIJ, 2004 (581): 127–134 (in Japanese).

[9] Chen C., Chen S., Liaw Jiunnjye. Application of low yield strength steel on controlled plastification ductile concentrically braced frames[J]. Canadian Journal of Civil Engineering, 2001, 28(5): 823-836.

[10] National Standard of the People’s Republic of China. GB 50017-2003 (Code for Design of Steel Structures) [S]. 2003, Beijing: China Planning Press.

[11] Merritt S., Uang C.-M. Giamnario Benzoni. Sub-assemblage Testing of Corebace Buckling-Restrained Braces [R]. 2003, San Diego: Department of Structural Engineering, University of California.