Electrical Characteristics of Plasma Plume During Pulse Wave Laser Welding

Abstract

To detect the real-time plasma plume during pulse wave Nd:YAG laser welding, experimental studies were conducted based on asynchronous signal acquisition system. The electrical signals of the laser-induced plasma plume were obtained by a passive acquisition system. The plume was directly observed and recorded using synchronous high-speed camera. The results showed that the waveform of the signals was in accordance with the periodical laser power. The signals decreased after the laser was turned on and fluctuated relatively steadily on the stable stage and then increased to 0 V after the laser beam was turned off. The decreasing time of the electrical signals was roughly 1.0 ms, and it decreased with the increasing peak power. However, the average power had insignificant effect on the signal decreasing time.

Keywords

Pulse wave / Laser welding / Plasma plume / Electrical signal / Passive probe

References

[1] You DY, Gao XD, Katayama S. Review of laser welding monitoring. Sci Technol Weld Join, 2013, 19(3): 181-201.

[2] Chen G, Zhang M, Zhao Z, et al. Measurements of laser-induced plasma temperature field in deep penetration laser welding. Opt Laser Technol, 2013, 45: 551-557.

[3] Rizzi D, Sibillano T, Calabrese PP, et al. Spectroscopic, energetic and metallographic investigations of the laser lap welding of AISI 304 using the response surface methodology. Opt Lasers Eng, 2011, 49(7): 892-898.

[4] Lacroix D, Jeandel G, Boudot C. Spectroscopic characterization of laser-induced plasma created during welding with a pulsed Nd:YAG laser. J Appl Phys, 1997, 81(10): 6599-6606.

[5] Atabaki MM, Yazdian N, Ma J, et al. High power laser welding of thick steel plates in a horizontal butt joint configuration. Opt Laser Technol, 2016, 83: 1-12.

[6] Zhao Y, Zhu K, Ma Q, et al. Plasma behavior and control with small diameter assisting gas nozzle during CO₂ laser welding. J Mater Process Technol, 2016, 237: 208-215.

[7] Yan C, Xie WJ, Yue W, et al. Numerical and experimental study of the effect of groove on plasma plume during high power laser welding. J Laser Appl, 2013, 25(5): 052005

[8] Tenner F, Brock C, Klämpfl F, et al. Analysis of the correlation between plasma plume and keyhole behavior in laser metal welding for the modeling of the keyhole geometry. Opt Lasers Eng, 2015, 64: 32-41.

[9] Sibillano T, Ancona A, Berardi V, et al. Real-time monitoring of laser welding by correlation analysis: The case of AA5083. Opt Lasers Eng, 2007, 45(10): 1005-1009.

[10] Sibillano T, Ancona A, Berardi V, et al. A real-time spectroscopic sensor for monitoring laser welding processes. Sensors (Basel), 2009, 9(5): 3376-3385.

[11] Sibillano T, Rizzi D, Ancona A, et al. Spectroscopic monitoring of penetration depth in CO₂ Nd:YAG and fiber laser welding processes. J Mater Process Technol, 2012, 212(4): 910-916.

[12] Sibillano T, Rizzi D, Mezzapesa FP, et al. Closed loop control of penetration depth during CO₂ laser lap welding processes. Sensors (Basel), 2012, 12(8): 11077-11090.

[13] Kawahito Y, Matsumoto N, Mizutani M, et al. Characterisation of plasma induced during high power fibre laser welding of stainless steel. Sci Technol Weld Join, 2008, 13(8): 744-748.

[14] Li L, Brookfield DJ, Steen WM. Plasma charge sensor for in-process, non-contact monitoring of the laser welding process. Meas Sci Technol, 1996, 7(4): 615-626.

[15] Bi C, Yang L, Xu W, et al. An electrical detection of the fluctuating plasma of laser welding with a passive probe. J Phys D Appl Phys, 2012, 45(38): 385202

[16] Liu T, Yang L, Wang L, et al. A comparative analysis of the passive electric probe detection and spectrum diagnosis of laser-induced plasma. Spectrosc Spectr Anal, 2014, 34(2): 289-292.

[17] Zhao S, Yang L, Liu T, et al. Analysis of plasma oscillations by electrical detection in Nd:YAG laser welding. J Mater Process Technol, 2017, 249: 479-489.

[18] Fujinaga S, Takenaka H, Narikiyo T, et al. Direct observation of keyhole behaviour during pulse modulated high-power Nd:YAG laser irradiation. J Phys D Appl Phys, 2000, 33(5): 492-497.

[19] Blecher JJ, Galbraith CM, Vlack CV, et al. Real time monitoring of laser beam welding keyhole depth by laser interferometry. Sci Technol Weld Join, 2014, 19(7): 560-564.

[20] Pang S, Chen X, Li W, et al. Efficient multiple time scale method for modeling compressible vapor plume dynamics inside transient keyhole during fiber laser welding. Opt Laser Technol, 2016, 77: 203-214.

[21] Tan W, Bailey NS, Shin YC. Investigation of keyhole plume and molten pool based on a three-dimensional dynamic model with sharp interface formulation. J Phys D Appl Phys, 2013, 46(5): 055501

[22] Matsunawa A, Kim JD, Seto N, et al. Dynamics of keyhole and molten pool in laser welding. J Laser Appl, 1998, 10(6): 247-254.

[23] Pang S, Chen X, Shao X, et al. Dynamics of vapor plume in transient keyhole during laser welding of stainless steel: local evaporation, plume swing and gas entrapment into porosity. Opt Lasers Eng, 2016, 82: 28-40.