Experimental study on surface integrity of Ti-6Al-4V in high speed side milling

Abstract

Aiming at the surface integrity of titanium alloy Ti-6Al-4V in high speed side milling, a series of side milling tests were carried out with uncoated carbide milling cutter at various milling speeds. Surface roughness, residual stress, subsurface microstructure and microhardness variations were investigated. The surface roughness measurement results present that the milling speed from 80 to 120 m/min fails to produce better and more stable roughness values compared with the result obtained from 320 to 380 m/min. The residual stresses in the feed direction and axial depth of cut direction are in similar trends for the two milling speed levels mentioned above. Moreover, the residual stress produced at 320 to 380 m/min is lower and more stable than that at 80 to 120 m/min. The microstructure analysis shows that the volume of β phase in the near surface becomes smaller and the deformation of β phase in the near surface becomes obvious with the increase of the milling speed. Subsurface microhardness variation was observed down to 200 μm below the machined surface at 80 to 120 m/min and down to 160 μm at 320 to 380 m/min. It is concluded that better surface integrity and higher material removal rate can be obtained at 320 to 380 m/min than at 80 to 120 m/min.

Keywords

surface roughness / residual stress / microhardness / microstructure

References

[1] Ezugwu E. O. Key improvements in the machining of difficult-to-cut aerospace superalloys[J]. International Journal of Machine Tools & Manufacture, 2005, 45(12–13): 1353-1367.

[2] Wang Kathy. The use of titanium for medical applications in the USA[J]. Materials Science and Engineering: A, 1996, 13(1/2): 134-137.

[3] Zoya Z. A., Krishnamurthy R. Performance of CBN tools in the machining of titanium alloys[J]. Journal of Materials Processing Technology, 2000, 100(1): 80-86.

[4] Che-Haron C. H., Jawaid A. The effect of machining on surface integrity of titanium alloy Ti-6%Al-4%V[J]. Journal of Materials Processing Technology, 2005, 166(2): 188-192.

[5] Sun J., Guo Y. B. A comprehensive experimental study on surface integrity by end milling Ti-6Al-4V[J]. Journal of Materials Processing Technology, 2009, 209(8): 4036 4042

[6] Durul U., Tugrul Ozel. Machining induced surface integrity in titanium and nickel alloys: A review[J]. International Journal of Machine Tools & Manufacture, 2011, 51(3): 250-280.

[7] Ginting A., Nouari M. Surface integrity of dry machined titanium alloys[J]. International Journal of Machine Tools & Manufacture, 2009, 49(3/4): 325-332.

[8] Che-Haron C. H. Tool life and surface integrity in turning titanium alloy[J]. Journal of Materials Processing Technology, 2001, 118(1–3): 231-237.

[9] Mantle A. L., Aspinwall D. K. Surface integrity of a high speed milled gamma titanium aluminide[J]. Journal of Materials Processing Technology, 2001, 118(1–3): 143-150.

[10] Sridhar B. R., Devananda G., Ramachandra K., et al. Effect of machining parameters and heat treatment on the residual stress distribution in titanium alloy IMI-834[J]. Journal of Materials Processing Technology, 2003, 139(1–3): 628-634.

[11] Chen L., EI-Wardany T. I., Harris W. C. Modeling the effects of flank wear land and chip formation on residual stress[J]. CIRP Annals-Manufacturing Technology, 2004, 53(1): 95-98.

[12] Velasquez J. D. P., Tidu A., Bolle B. Subsurface and surface analysis of high speed machined Ti-6Al-4V alloy[J]. Materials and Engineering:A, 2010, 527(10/11): 2572-2578.

[13] Rao B., Dandekar Chinmaya R., Shin Yung C. An experimental and numerical study on the face milling of Ti-6Al-4V alloy: Tool performance and surface integrity[J]. Journal of Materials Processing Technology, 2011, 211(2): 294-304.

[14] Yang Z. C., Zhang D. H., Yao C. F. Study on the high speed milling parameters on surface integrity of titanium alloy TC4[J]. Journal of Northwestern Polytechnical University, 2009, 27(4): 538-543.

[15] Seguy S., Dessein G., Arnaud L. Surface roughness variation of thin wall milling related to modal interactions[J]. International Journal of Machine Tools & Manufacture, 2008, 48(3–4): 261-274.

[16] Zhang G., Yu C., Shi R., et al. Experimental study on the milling of thin parts of titanium alloy (TC4) [J]. Journal of Materials Processing Technology, 2003, 138(1–3): 489-493.

[17] Ginting A., Nouari M. Experimental and numerical studies on the performance of alloyed carbide tool in dry milling of aerospace material[J]. International Journal of Machine Tools and Manufacture, 2006, 46(7–8): 758-768.

[18] Nouari M., Ginting A. Wear characteristics and performance of multi-layer CVD-coated carbide tool in dry milling of titanium alloy[J]. Surface and Coatings Technology, 2006, 200(18–19): 5663-5676.

[19] Lapin J., Pelachová T. Microstructure stability of a cast Ti-45.2Al-2V-0.6Si-0.7B alloy at temperatures 973 — 1,073,K[J]. Intermetallics, 2006, 14(10/11): 1175-1180.