Detection of solder bump defects on a flip chip using vibration analysis

Abstract

Flip chips are widely used in microelectronics packaging owing to the high demand of integration in IC fabrication. Solder bump defects on flip chips are difficult to detect, because the solder bumps are obscured by the chip and substrate. In this paper a nondestructive detection method combining ultrasonic excitation with vibration analysis is presented for detecting missing solder bumps, which is a typical defect in flip chip packaging. The flip chip analytical model is revised by considering the influence of spring mass on mechanical energy of the system. This revised model is then applied to estimate the flip chip resonance frequencies. We use an integrated signal generator and power amplifier together with an air-coupled ultrasonic transducer to excite the flip chips. The vibrations are measured by a laser scanning vibrometer to detect the resonance frequencies. A sensitivity coefficient is proposed to select the sensitive resonance frequency order for defect detection. Finite element simulation is also implemented for further investigation. The results of analytical computation, experiment, and simulation prove the efficacy of the revised flip chip analytical model and verify the effectiveness of this detection method. Therefore, it may provide a guide for the improvement and innovation of the flip chip on-line inspection systems.

Keywords

flip chip / defect detection / ultrasonic excitation / vibration analysis

References

[1] Mallik D, Radhakrisham K, He J. Advanced package technologies for high-performance systems. Intel Technology Journal, 2005, 9(4): 259–271

[2] Marks M R. Novel deprocessing technique for failure analysis of flip-chip integrated circuit packages. Practical Failure Analysis, 2001, 1(6): 45–52

[3] Verma K, Han B. Real-time observation of thermally induced warpage of flip-chip package using far-infrared Fizeau interferometry. Experimental Mechanics, 2004, 44(6): 628–633

[4] O’Conchuir D, McCurdy J, Casey V. Survey of non-destructive inspection methods for solder joint integrity. In: Proceedings of the IEEE 1991 National Aerospace and Electronics Conference, Dayton, 1991, 1268–1275

[5] Wang Z F, Choudhry M. A study of flip-chip open solder bump failure mechanism. In: Proceedings of the 32nd International Symposium for Testing and Failure Analysis. Austin, 2006, 239–242

[6] Capson D W, Eng S K. A tiered-color illumination approach for machine inspection of solder joints. IEEE Transactions on Pattern Analysis and Machine Intelligence, 1988, 10(3): 387–393

[7] Pacheco M, Wang Z Y, Skoglund L. Advanced fault isolation and failure analysis techniques for future package technologies. Intel Technology Journal, 2005, 9(4): 337–352

[8] Brand S, Czurratis P, Hoffrogge P, Petzold M. Automated inspection and classification of flip-chip-contacts using scanning acoustic microscopy. Microelectronics and Reliability, 2010, 50(9–11): 1469–1473

[9] Chiu S H, Chen C. Investigation of void nucleation and propagation during electromigration of flip-chip solder joints using X-ray microscopy. Applied Physics Letters, 2006, 89(26): 1–3

[10] Gür C H. Investigation of the influence of specimen geometry on quench behaviour of steels by X-ray determination of surface residual stresses. International Journal of Mechanical Sciences, 2002, 44(7): 1335–1347

[11] Pacheco M, Goyal D. X-ray computed tomography for non-destructive failure analysis in microelectronics. 2010 IEEE International Reliability Physics Symposium. Garden Grove, CA, Canada, 2010: 252–258.

[12] El-Gomati M, Zaggout F, Jayacody H, Tear S, Wilson K. Why is it possible to detect doped regions of semiconductors in low voltage SEM: a review and update. Surface and Interface Analysis, 2005, 37(11): 901–911

[13] Yoshino M, Aoki T, Shirakashi T, Komanduri R. Some experiments on the scratching of silicon: In situ scratching inside an SEM and scratching under high external hydrostatic pressures. International Journal of Mechanical Sciences, 2001, 43(2): 335–347

[14] Chai T C, Wong B S, Bai W M, Trigg A, Lam Y K. A novel defect detection technique using active transient thermography for high density package and interconnections. In: Proceedings of the 53rd Electronic Components and Technology Conference, New Orleans, 2003, 920–925.

[15] Yang J, Ume I C. Quality inspection of flip chip solder bumps using integrated analytical, numerical, and experimental modal analyses. Journal of Electronic Packaging, 2008, 130(3): 1–10

[16] Yang J, Ume I C, Zhang L Z. Defect detection of flip chip solder bumps with wavelet analysis of laser ultrasound signals. IEEE Transactions on Advanced Packaging, 2010, 33(1): 19–29

[17] Oresjo S. New study reveals component defect levels. Circuits Assembly 2002, 39–43

[18] Lee C R, Kam T Y. System identification of partially restrained composite plates using measured natural frequencies. Journal of Engineering Mechanics, 2006, 132(8): 841–850

[19] Mathews J H, Fink K K. Numerical Methods Using MATLAB. 4th ed. Pearson Education Inc., 2004.

[20] Huber T M, Hagemeyer S D, Ofstad E T, Fatemi M, Kinnick R R, Greenleaf J F. Noncontact modal excitation of small structures using ultrasound radiation force. In: Proceedings of the SEM Annual Conference and Exposition on Experimental and Applied Mechanics, Springfield, 2007, 604–610.

[21] Konofagou E E, Hynynen K. Localized harmonic motion imaging: theory, simulations and experiments. Ultrasound in Medicine & Biology, 2003, 29(10): 1405–1413

[22] Hamdan M N, Al-Qaisia A A, Al-Bedoor B O. Comparison of analytical techniques for nonlinear vibrations of a parametrically excited cantilever. International Journal of Mechanical Sciences, 2001, 43(6): 1521–1542

[23] Liu S, Ume I C. Vibration analysis based modeling and defect recognition for flip-chip solder-joint inspection. Journal of Electronic Packaging, 2002, 124(3): 221–226

Acknowledgements

The authors thank the financial support of the National basic Research Program of China (No. 2009CB724204) and the National Natural Science Foundation of China (Grant No. 50975106).

RIGHTS & PERMISSIONS

2014 Higher Education Press and Springer-Verlag Berlin Heidelberg