RESEARCH ARTICLE

Thermal and catalytic pyrolysis of a synthetic mixture representative of packaging plastics residue

  • Simona Colantonio 1 ,
  • Lorenzo Cafiero 1 ,
  • Doina De Angelis 1 ,
  • Nicolò M. Ippolito 2 ,
  • Riccardo Tuffi , 1 ,
  • Stefano Vecchio Ciprioti 3
Expand
  • 1. Department for Sustainability, ENEA—Casaccia Research Center, Rome 00123, Italy
  • 2. Department of Chemical, Materials and Environmental Engineering, Sapienza University of Rome, Rome 00184, Italy
  • 3. Department of SBAI, Sapienza University of Rome, Rome 00161, Italy

Received date: 10 Feb 2019

Accepted date: 02 Jun 2019

Published date: 15 Apr 2020

Copyright

2019 Higher Education Press and Springer-Verlag GmbH Germany, part of Springer Nature

Abstract

A synthetic mixture of real waste packaging plastics representative of the residue from a material recovery facility (plasmix) was submitted to thermal and catalytic pyrolysis. Preliminary thermogravimetry experiments coupled with Fourier transform infrared spectroscopy were performed to evaluate the effects of the catalysts on the polymers’ degradation temperatures and to determine the main compounds produced during pyrolysis. The thermal and catalytic experiments were conducted at 370°C, 450°C and 650°C using a bench scale reactor. The oil, gas, and char yields were analyzed and the compositions of the reaction products were compared. The primary aim of this study was to understand the effects of zeolitic hydrogen ultra stable zeolite Y (HUSY) and hydrogen zeolite socony mobil-5 (HZSM5) catalysts with high silica content on the pyrolysis process and the products’ quality. Thermogravimetry showed that HUSY significantly reduces the degradation temperature of all the polymers—particularly the polyolefines. HZSM5 had a significant effect on the degradation of polyethylene due to its smaller pore size. Mass balance showed that oil is always the main product of pyrolysis, regardless of the process conditions. However, all pyrolysis runs performed at 370°C were incomplete. The use of either zeolites resulted in a decrease in the heavy oil fraction and the prevention of wax formation. HUSY has the best performance in terms of the total monoaromatic yield (29 wt-% at 450°C), while HZSM5 promoted the production of gases (41 wt-% at 650°C). Plasmix is a potential input material for pyrolysis that is positively affected by the presence of the two tested zeolites. A more effective separation of polyethylene terephthalate during the selection process could lead to higher quality pyrolysis products.

Cite this article

Simona Colantonio , Lorenzo Cafiero , Doina De Angelis , Nicolò M. Ippolito , Riccardo Tuffi , Stefano Vecchio Ciprioti . Thermal and catalytic pyrolysis of a synthetic mixture representative of packaging plastics residue[J]. Frontiers of Chemical Science and Engineering, 2020 , 14(2) : 288 -303 . DOI: 10.1007/s11705-019-1875-3

Electronic Supplementary Material

Supplementary material is available in the online version of this article at https://doi.org/10.1007/s11705-019-1875-3 and is accessible for authorized users.
1
Association of Plastics Manufacturers. Plastics—the facts 2018. An analysis of European latest plastics production, demand and waste data. Plastic Europe, 2018

2
Wang C Q, Wang H, Fu J G, Liu Y N. Flotation separation of waste plastics for recycling—A Review. Waste Management (New York, N.Y.), 2015, 41: 28–38

DOI

3
The European Parliament and the Council of the European Union. Directive 2018/852/EU amending Directive 94/62/EC on packaging and packaging waste. 2018

4
Adrados A, de Marco I, Caballero B M, López A, Laresgoiti M F, Torres A. Pyrolysis of plastic packaging waste: A comparison of plastic residuals from material recovery facilities with simulated plastic waste. Waste Management (New York, N.Y.), 2012, 32(5): 826–832

DOI

5
Tuffi R, D’Abramo S, Cafiero L M, Trinca E, Vecchio Ciprioti S. Thermal behavior and pyrolytic degradation kinetics of polymeric mixtures from waste packaging plastics. Express Polymer Letters, 2018, 12(1): 82–99

DOI

6
Panda A K, Singh R K, Mishra D K. Thermolysis of waste plastics to liquid fuel A suitable method for plastic waste management and manufacture of value-added products—A world prospective. Renewable & Sustainable Energy Reviews, 2010, 14(1): 233–248

DOI

7
Kiran N, Ekinci E, Snape C E. Recycling of plastics wastes via pyrolysis. Resources, Conservation and Recycling, 2000, 29(4): 273–283

DOI

8
Jamradloedluk J, Lertsatitthanakorn C. Characterization and utilization of char derived from fast pyrolysis of plastic wastes. Procedia Engineering, 2014, 69: 1437–1442

DOI

9
Wampler T P. Applied Pyrolyis Handbook. 2nd ed. New York: Marcel Dekker Inc., 1995, 77–96

10
Grassie N, Scott G. Polymer Degradation and Stabilization. 1st ed. London: Cambridge University Press, 1985, 23–34

11
Achilias D S, Kanellopoulou I, Megalokonomos P, Antonakou E, Lappas A. Chemical recycling of polystyrene by pyrolysis: Potential use of the liquid product for the reproduction of polymer. Macromolecular Materials and Engineering, 2007, 292(8): 923–934

DOI

12
Lovink H J, Pine L A. Hydrocarbon Chemistry of FCC Naphtha Formation. Paris: Technip Editions, 1990, 165–172

13
Miandad R, Barakat M A, Aburiazaiza A S, Rehan M, Nizami A S. Catalytic pyrolysis of plastic waste: A review. Process Safety and Environmental Protection, 2016, 102: 822–838 doi:10.1016/j.psep.2016.06.022

14
Zhao W, Hasegawa S, Fujita J, Yoshii F, Sasaki T, Makuuchi K, Sun J, Nishimoto S. Effects of zeolites on the pyrolysis of polypropylene. Polymer Degradation & Stability, 1996, 53(1): 129–135

DOI

15
Serrano D P, Aguado J, Escola J M. Developing advanced catalysts for the conversion of polyolefinic waste plastics into fuels and chemicals. ACS Catalysis, 2012, 2(9): 1924–1941

DOI

16
Buekens A G, Huang H. Catalytic plastics cracking for recovery of gasoline-range hydrocarbons from municipal plastic wastes. Resources, Conservation and Recycling, 1998, 23(3): 163–181

DOI

17
de Marco I, Caballero B M, Lopez A, Laresgoiti M F, Torres A, Chomon M J. Pyrolysis of the rejects of a waste packaging separation and classification plant. Journal of Analytical and Applied Pyrolysis, 2009, 85(1-2): 384–391

DOI

18
Muhammad C, Onwudili J A, Williams P T. Catalytic prolysis of waste plastic from electrical and electronc equipment. Journal of Analytical and Applied Pyrolysis, 2015, 113: 332–339

DOI

19
Santella C, Cafiero L M, De Angelis D, La Marca F, Tuffi R, Vecchio Ciprioti S. Thermal and catalytic pyrolysis of a mixture of plastics from small waste electrical and electronic equipment (WEEE). Waste Management (New York, N.Y.), 2016, 54: 143–152

DOI

20
Al-Salem S M, Antelava A, Constantinou A, Manos G, Dutta A. A review on thermal and catalytic pyrolysis pf plastic solid waste (PSW). Journal of Environmental Management, 2017, 197: 177–198 doi:10.1016/j.jenvman.2017.03.084

21
Lee K H. Feedstock Recycling and Pyrolysis of Waste Plastics. 1st ed. Chichester: John Wiley & Sons, 2006, 129–157

22
Faravelli T, Pinciroli M, Pisano F, Bozzano G, Dente M, Ranzi E. Thermal degradation of polystyrene. Journal of Analytical and Applied Pyrolysis, 2001, 60(1): 103–121

DOI

23
Demirbas A. Pyrolysis of municipal plastic wastes for recovery of gasoline-range hydrocarbons. Journal of Analytical and Applied Pyrolysis, 2004, 72(1): 97–102

DOI

24
Angyal A, Miskolczi N, Bartha L. Petrochemical feedstock by thermal cracking of plastic waste. Journal of Analytical and Applied Pyrolysis, 2007, 79(1-2): 409–414

DOI

25
Cafiero L M, Fabbri D, Trinca E, Tuffi R, Vecchio Ciprioti S. Thermal and spectroscopic (TG/DCS-FTIR) characterization of mixed plastics for materials and energy recovery under pyrolytic conditions. Journal of Thermal Analysis and Calorimetry, 2015, 121(3): 1111–1119

DOI

26
Seo Y, Lee K, Shin D. Investigation of catalytic degradation of high density polyethylene by hydrocarbon group type analysis. Journal of Analytical and Applied Pyrolysis, 2003, 70(2): 383–398

DOI

27
Onwudili J A, Insura N, Williams P T. Composition of products from the pyrolysis of polyethylene and polystyrene in a closed batch reactor: Effects of temperature and residence time. Journal of Analytical and Applied Pyrolysis, 2009, 86(2): 293–303

DOI

28
López A, de Marco I, Caballero B M, Adrados A, Laresgoiti M F. Deactivation and regeneration of ZSM-5 zeolite in catalytic pyrolysis of plastic wastes. Waste Management (New York, N.Y.), 2011, 31(8): 1852–1858

DOI

29
Benedetti M, Cafiero L, De Angelis D, Dell’Era A, Pasquali M, Stendardo S, Tuffi R, Ciprioti S V. Pyrolysis of WEEE plastics using catalysts produced from fly ash of coal gasification. Frontiers of Environmental Science & Engineering, 2017, 11(5): 11–21

DOI

30
Kidany A J, Parrish W R. Fundamentals of Natural Gas Processing. 1st ed. New York: Taylor & Francis, 2006, 354–360

31
Marcilla A, Gomez-Siurana A, Berenguer D. Study of the influence of the characteristics of different acid solid in the catalytic pyrolysis of different polymers. Applied Catalysis, 2006, 301(2): 222–231

DOI

32
Marcilla A, Gomez-Siurana A, Valdes F. Catalytic pyrolysis of LDPE over H-beta and HZSM5 zeolites in dynamic conditions study of the evolution of the process. Journal of Analytical and Applied Pyrolysis, 2007, 79(1-2): 433–442

DOI

33
Agullo J, Kumar N, Berenguer D, Kubicka D, Marcilla A, Gomez A, Salmi T, Murzin D Y. Catalytic pyrolysis of low-density polyethylene over H-b, H-Y, H-Mordenite and H-Ferrierite zeolite catalysts: Influence of acidity and structures. Kinetics and Catalysis, 2007, 48(4): 535–540

DOI

34
Manos G, Garforth A, Dwyer J. Catalytic degradation of high-density polyethylene over different zeolitic structures. Industrial & Engineering Chemistry Research, 2000, 39(5): 1198–1202

DOI

35
Csicsery S M. Catalysis by shape selective zeolites-science and technology. Pure and Applied Chemistry, 1986, 6(6): 841–856

DOI

36
Williams P T, Slaney E. Analysis of products from the pyrolysis and liquefaction of single plastics and waste plastic mixtures. Resources, Conservation and Recycling, 2007, 51(4): 754–769

DOI

37
Kaminsky W, Zorriqueta I J N. Catalytical and thermal pyrolysis of polyolefins. Journal of Analytical and Applied Pyrolysis, 2007, 79(1-2): 368–374

DOI

38
Ates F, Miskolczi N, Borsodi N. Comparison of real waste (MSW and MPW) pyrolysis in batch reactor over different catalysts. Part I: product yields, gas and pyrolysis oil properties. Bioresource Technology, 2013, 133: 443–454

DOI

39
Green D W, Perry R H. Perry’s Chemical Engineers’ Handbook. 8th ed. New York: McGraw-Hill, 2007, 24–34

40
Serrano D P, Aguado J, Escola J M. Catalytic cracking of a polyolefin mixture over different acid solid catalysts. Industrial & Engineering Chemistry Research, 2000, 39(5): 1177–1184 doi:10.1021/ie9906363

41
Serrano D P, Aguado J, Escola J M, Rodriguez J M, San Miguel G. An investigation into the catalytic cracking of LDPE using Py-GC/MS. Journal of Analytical and Applied Pyrolysis, 2005, 74(1-2): 370–378

DOI

42
Olson D H, Kokotailo G T, Lawton S L, Meler W M. Crystal structure and structure-related properties of ZSM-5. Journal of Physical Chemistry, 1981, 85(15): 2238–2243

DOI

43
Serrano D P, Aguado J, Escola J M. Catalytic conversion of polystyrene over HMCM-41, HZSM-5 and amorphous SiO2-Al2O3: Comparison with thermal cracking. Applied Catalysis B: Environmental, 2000, 25(2-3): 181–189

DOI

44
Aguado J, Sotelo J L, Serrano D P, Calles J A, Escola J M. Catalytic conversion of polyolefins into liquid fuels over MCM-41: Comparison with ZSM-5 and amorphous SiO2-Al2O3. Energy & Fuels, 1997, 11(6): 1225–1231

DOI

45
Audisio G, Silvani A, Beltrame P L, Carniti P. Catalytic thermal degradation of polymers: Degradation of polypropylene. Journal of Analytical and Applied Pyrolysis, 1984, 7(1-2): 83–90

DOI

46
Tae J, Jang B, Kim J, Kim I, Park D. Catalytic degradation of polystyrene using acid-treated halloysite clays. Solid State Ionics, 2004, 172(1-4): 129–133

DOI

47
Marcilla A, Beltran M I, Navarro R. Thermal and catalytic pyrolysis of polyethylene over HZSM5 and HUSY zeolites in a batch reactor under dynamic conditions. Applied Catalysis B: Environmental, 2009, 86(1-2): 78–86

DOI

48
Zhang Z, Hirose T, Nishio S, Morioka Y, Azuma N, Ueno A, Ohkita H, Okada M. Chemical recycling of waste polystyrene into styrene over solid acids and bases. Industrial & Engineering Chemistry Research, 1995, 34(12): 4514–4519

DOI

49
Whyte H E, Loubar K, Awad S, Tazerout M. Pyrolytic oil production by catalytic pyrolysis of refuse-derived fuels: Investigation of low cost catalysts. Fuel Processing Technology, 2015, 140: 32–38 doi:10.1016/j.fuproc.2015.08.022

50
Murzin D. Chemical Engineering for Renewable Conversion. 1st ed. Oxford: Academic Press, 2013, 76–132

51
Imam T, Capareda S. Characterization of bio-oil, syn-gas and bio-char from switchgrass pyrolysis at various temperatures. Journal of Analytical and Applied Pyrolysis, 2012, 93: 170–177

DOI

52
Corma A, Orchilles A V. Current views on the mechanism of catalytic cracking. Microporous and Mesoporous Materials, 2000, 35-36: 21–30

DOI

53
Vogt E T C, Weckhuysen B M. Fluid catalytic cracking: Recent developments on the grand old lady of zeolite catalysis. Chemical Society Reviews, 2015, 44(20): 7342–7370

DOI

54
Audisio G, Bertini F, Beltrame P, Carniti P. Catalytic degradation of polymers: Part III. Degradation of polystyrene. Polymer Degradation & Stability, 1990, 29(2): 191–200

DOI

Outlines

/