Phenolic rigid organic filler/isotactic polypropylene composites. III. Impact resistance property

Abstract

A novel phenolic rigid organic filler (KT) was used to modify isotactic polypropylene (iPP). The influence of KT particles on the impact resistance property of PP/KT specimens (with similar interparticles distance, 1.8 μm) was studied by notched izod impact tests. It was found that the brittle-ductile transition (BDT) of the PP/KT microcomposites took place at the filler content of about 4%, and the impact strength attains the maximum at 5% (with filler particles size of 1.5 μm), which is about 2.5 times that of unfilled iPP specimens. The impact fracture morphology was investigated by scanning electron microscopy (SEM). For the PP/KT specimens and the high-density polyethylene/KT (HDPE/KT) specimens in ductile fracture mode, many microfibers could be found on the whole impact fracture surface. It was the filler particles that induced the plastic deformation of interparticles ligament and hence improved the capability of iPP matrix on absorbing impact energy dramatically. The determinants on the BDT were further discussed on the basis of stress concentration and debonding resistance. It can be concluded that aside from the interparticle distance, the filler particles size also plays an important role in semicrystalline polymer toughening.

Keywords

rigid organic filler / polypropylene / impact resistance

References

[1] Karger-Kocsis J, ed. Polypropylene: composites, London: Chapman & Hall, 1995. Chapter 1

[2] Baker R A, Koller L L, Kummer P E. Handbook of fillers for plastics, 2nd ed. New York: Van Nostrand Reinhold, 1987

[3] Thio Y S, Argon A S, Cohen R E, Weinberg M. Toughening of isotactic polypropylene with CaCO₃ particles. Polymer, 2002, 43(13): 3661-3674

[4] Zuiderduin W C J, Westzaan C, Huétink J, Gaymans R J. Toughening of polypropylene with calcium carbonate particles. Polymer, 2003, 44(1): 261-275

[5] Zhang Q X, Yu Z Z, Xie X L, Mai Y W. Crystallization and impact energy of polypropylene/CaCO₃ nanocomposites with nonionic modifier. Polymer, 2004, 45(17): 5985-5994

[6] Liang J Z, Li R K Y. Brittle-ductile transition in polypropylene filled with glass beads. Polymer, 1999, 40(11): 3191-3195

[7] Wu X, Zhu X, Qi Z. The 8th International conference on deformation, yield and fracture of polymers. London: The Plastics and Rubber Institute, 1991:78/1

[8] Muratoglu O K, Argon A S, Cohen R E, Weinberg M. Crystalline morphology of polyamide-6 near planar surfaces. Polymer, 1995, 36(11): 2143-2152

[9] Bartczak Z, Argon A S, Cohen R E, Kowalewski T. The morphology and orientation of polyethylene in films of sub-micron thickness crystallized in contact with calcite and rubber substrates. Polymer, 1999, 40(9): 2367-2380

[10] Muratoglu O K, Argon A S, Cohen R E, Weinberg M. Toughening mechanism of rubber-modified polyamides. Polymer, 1995, 36(5): 921-930

[11] Muratoglu O K, Argon A S, Cohen R E, Weinberg M. Microstructural processes of fracture of rubber-modified polyamides. Polymer, 1995, 36(25): 4771-4786

[12] Wang Y, Fu Q, Li Q, Zhang G, Shen K, Wang Y Z. Ductile-brittle-transition phenomenon in polypropylene/ethylene-propylene-diene rubber blends obtained by dynamic packing injection molding: A new understanding of the rubber-toughening mechanism. J Polym Sci: Polym Phys, 2002, 40(18): 2086-2097

[13] Qi D M, Yang L, Wu M H, Lin H M, Nitta K H. Phenolic rigid organic filler/isotactic polypropylene composites. I. preparation. Frontiers of Chemical Engineering in China, 2008, 2(3): 236-241

[14] Rong M Z, Zhang M Q, Zheng Y X, Zeng H M, Friedrich K. Improvement of tensile properties of nano-SiO₂/PP composites in relation to percolation mechanism. Polymer, 2001, 42(7): 3301-3304

[15] Jancar J, Dianselmo A. The yield strength of particulate reinforced thermoplastic composites. Polym Eng Sci, 1992, 32(18): 1394-1399

[16] Fu Q, Wanh G, Shen J. Polyethylene toughened by CaCO₃ particle: Brittle-ductile transition of CaCO₃-toughened HDPE. J Appl Polym Sci, 1993, 49(4): 673-677

[17] Chen S G, Hu J W, Zhang M Q, Rong M Z, Zheng Q. Time dependent percolation of carbon black filled polymer composites in response to solvent vapor. J Mater Sci, 2005, 40(8): 2065-2068

[18] Wang K, Wu J S, Zeng H M. Microstructure and fracture behavior of polypropylene/barium sulfate composites. J Appl Polym Sci, 2006, 99(3): 1207-1213

[19] Bikiaris D N, Papageorgiou G Z, Pavlidou E, Vouroutzis N, Palatzoglou P, Karayannidis G P. Preparation by melt mixing and characterization of isotactic polypropylene/SiO₂ nanocomposites containing untreated and surface-treated nanoparticles. J Appl Polym Sci, 2006, 100(4): 2684-2696

[20] Dubnikova I L, Berezina S M, Antonov A V. Effect of rigid particle size on the toughness of filled polypropylene. J Appl Polym Sci, 2004, 94(5): 1917-1926

[21] Hutchinson J W. Crack tip shielding by micro-cracking in brittle solids. Acta metallurgica, 1987, 35(7):1605-1619

[22] Bartczak Z, Argon A S, Cohen R E, Weinberg M. Toughness mechanism in semi-crystalline polymer blends: I. High-density polyethylene toughened with rubbers Polymer,1999, 40 (9): 2331-2346; II. High-density polyethylene toughened with calcium carbonate filler particles. Polymer, 1999, 40(9): 2347-2365

[23] Qi D M, Shao J Z, Wu M H, Nitta K H. Phenolic rigid organic filler/isotactic polypropylene composites. II. tensile properites. Frontiers of Chemical Engineering in China, 2008, 2(4): 396-401

[24] Mccrum N G, Buckley C B, Bucknall C B. Principles of Polymer Engineering. New York: Oxford University Press,, 1997

Acknowledgements

This work was supported by Japan Science and Technology Agency (JST), the National Natural Science Foundation of China (Grant No. 50803058), Program for Changjiang Scholars and Innovative Research Team in University (No. 0654).

RIGHTS & PERMISSIONS

2014 Higher Education Press and Springer-Verlag Berlin Heidelberg