Recent research has clarified the sequence of ground deformation mechanisms that manifest themselves when excavations are made in soft ground. Furthermore, a new framework to describe the deformability of clays in the working stress range has been devised using a large database of previously published soil tests. This paper aims to capitalize on these advances, by analyzing an expanded database of ground movements associated with braced excavations in Shanghai. It is shown that conventional design charts fail to take account either of the characteristics of soil deformability or the relevant deformation mechanisms, and therefore introduce significant scatter. A new method of presentation is found which provides a set of design charts that clarify the influence of soil deformability, wall stiffness, and the geometry of the excavation in relation to the depth of soft ground.
Geotechnical uncertainties may play crucial role in response prediction of a structure with substantial soil-foundation-structure-interaction (SFSI) effects. Since the behavior of a soil-foundation system may significantly alter the response of the structure supported by it, and consequently several design decisions, it is extremely important to identify and characterize the relevant parameters. Moreover, the modeling approach and the parameters required for the modeling are also critically important for the response prediction. The present work intends to investigate the effect of soil and model parameter uncertainty on the response of shallow foundation-structure systems resting on dry dense sand. The SFSI is modeled using a beam-on-nonlinear-winkler-foundation (BNWF) concept, where soil beneath the foundation is assumed to be an assembly of discrete, nonlinear elements composed of springs, dashpots and gap elements. The sensitivity of both soil and model input parameters on shallow foundation responses are investigated using first-order second-moment (FOSM) analysis and Monte Carlo simulation through Latin hypercube sampling technique. It has been observed that the degree of accuracy in predicting the responses of the shallow foundation is highly sensitive soil parameters, such as friction angle, Poisson’s ratio and shear modulus, rather than model parameters, such as stiffness intensity ratio and spring spacing; indicating the importance of proper characterization of soil parameters for reliable soil-foundation response analysis.
While the soil nails and the corresponding compound technology are widely used as the support techniques for deep foundation pit and normal slopes, few related engineering cases are found for high loess slopes. By utilizing the finite element software of PLAXIS 8.5, the behavior of a high loess slope reinforced by the combination of soil nails and stabilization piles (hereinafter for CSNSP) is studied in this paper. It can be found that the potential slide surface of the slope moves to deeper locations during the process of the multi-staged excavations. The measure of reducing the weight of the top of the slope is a positive factor to the stability of the loess slope, while the rainfall is a negative factor. The slope can’t be stable if it’s reinforced only by stabilization piles or soil nails during the process of the multi-staged excavations. The soil nail contributes greater to the overall system stability when the excavation depth is relatively shallow, while the stabilization pile takes it over when the excavation depth reaches a large value. Compared to the results from the Sweden circular slip surface, the data derived from the method of phi/c reduction is relatively large when the slope is unreinforced or reinforced only by stabilization pile, and the data turns to be small when the slope is strengthened by soil nails or the combination system of soil nails and stabilization piles.
This research experimentally examined the strength, failure modes, and behaviors of dowel-bearing and fiber-bearing wood beam-column connections and explored the effects of cyclic loading on the strength, failure modes, and behaviors of those connections. Base on limited numbers of exploratory laboratory tests (6 preliminary tests in total), the authors observed that the typical bolted connection (dowel-bearing type wood beam-column connection with fiber-bearing surfaces) showed good behavior (large peak moment) under the monotonic loads, and the tenon joint connection (fiber-bearing wood beam-column connection) showed good behavior under cyclic loads. The cyclic property of loading reduced the strength of the dowel-bearing type wood beam-column connections, but increased the strength of fiber-bearing type wood beam-column connections. More importantly, the authors identified a possible location of safety concern in current national design specifications (NDS) standards for the typical bolted connection (dowel-bearing connection with fiber bearing surface) under cyclic loading because the tested value was smaller than the NDS calculated value. But, because of the small amount of tests conducted, no final conclusion can be drawn based on those preliminary observations yet. A large number of repetitive laboratory tests should be conducted.
Many researches have been carried out to study the fresh and hardened properties of concrete containing crumb rubber as replacement to fine aggregate by volume, yet there is no specific guideline has been developed on the mix design of the rubbercrete. The experimental program, which has been developed and reported in this paper, is designed and executed to provide such mix design guidelines. A total of 45 concrete mixes with three different water to cement ratio (0.41, 0.57 and 0.68) were cast and tested for fresh and mechanical properties of rubbercrete such as slump, air content, unit weight, compressive strength, flexural strength, splitting tensile strength and modulus of elasticity. Influence of mix design parameters such as percentage of crumb rubber replacement, cement content, water content, fine aggregate content, and coarse aggregate content were investigated. Three levels of slump value (for conventional concrete mixes) has been selected; low, medium and high slump. In each slump level, water content was kept constant. Equations for the reduction factors (RFs) for compressive strength, flexural strength, splitting tensile strength and modulus of elasticity have been developed. These RFs can be used to design rubbercrete mixes based on the conventional mix (0% crumb rubber content)
This paper experimentally investigates the energy absorption potential of two types of concrete floors, namely, normal density concrete and structural low-density concrete, containing secondary (shrinkage and temperature) reinforcements. The test program considered the following secondary reinforcements: 1) traditional welded-wire steel mesh, 2) steel fiber and 3) poly composite fiber. To estimate the extent to which crushing of floor slab materials would help absorb energy, a series of concrete penetration tests employing patch loading was undertaken on scaled down model slabs. Each concrete-secondary reinforcement combination considered slabs of 50 mm in depth with square plan dimensions ranging from 50 to 500 mm, resulting in a total of 30 test specimens. The first part of the paper discusses the test specimens, the test setup, and the test procedure. The second part of the paper presents the experimental results and establishes the energy absorption of different concrete- secondary reinforcement combinations. Sieve analysis results of the crushed specimens were used to derive a “work index” value that relates the pulverized particle size distributions to energy inputs. The work index values of concrete-secondary reinforcement systems can be used to assess the energy dissipation potential associated with such floor slabs in buildings undergoing progressive collapse. The results indicate that floors with secondary reinforcements could play an important role in helping arrest global progressive collapse.
Recent researchers have discovered microtremor applications for evaluating the liquefaction potential. Microtremor measurement is a fast, applicable and cost-effective method with extensive applications. In the present research the liquefaction potential has been reviewed by utilization of microtremor measurement results in Babol city. For this purpose microtremor measurements were performed at 60 measurement stations and the data were analyzed by suing Nakmaura’s method. By using the fundamental frequency and amplification factor, the value of vulnerability index (
The objective of this study is to choose indices for the characterization of aggregate form and angularity for large scale application. For this purpose, several parameters for aggregate form and angularity featured in previous research are presented. Then, based on these established parameters, 200 coarse quartzite aggregates are analyzed herein by using image processing technology. This paper also analyzes the statistical distributions of parameters for aggregate form and angularity as well as the correlation between form and angularity parameters. It was determined that the parameters for form or angularity of coarse aggregates could be fitted by either normal distribution or log-normal distribution at a 95% confidence level. Some of the form parameters were influenced by changes in angularity characteristics, while aspect ratio and angularity using outline slope, area ratio and radius angularity index, and aspect ratio and angularity index were independent of each other, respectively; and consequently, the independent parameters could be used to quantify the aggregate form and angularity for the purpose to study the influence of aggregate shape on the mechanical behavior of concrete. Furthermore, results from this study’s in-depth investigations showed that the aspect ratio and the angularity index can further understanding of the effects of coarse aggregates form and angularity on concrete mechanical properties, respectively. Finally, coarse aggregates with the same content, type and surfaces texture, but different aspect ratios and angularity indices were used to study the influence of coarse aggregate form and angularity on the behavior of concrete. It was revealed that the splitting tensile strength of concrete increased with increases in the aspect ratio or angularity index of coarse aggregates.