Effectiveness of external prestressing in enhancing the non-ductile hanger failure mechanism in reinforced concrete inverted T-beams

Abstract

Recently, inverted T-beams have been used in reinforced concrete (RC) bridges to support transverse precast stringers. Inverted T-beams, contrary to practice with conventional beams, are loaded on the flanges upper surface. This loading configuration causes hanger failure due to the generation of vertical tensile stresses near the bottom of the web. The key purpose of this study is to investigate the efficiency of vertical external prestressing stainless-steel bars in mitigating non-ductile hanger failure in reinforced concrete inverted T-beams. An experimental study on six inverted-T beams, including two un-strengthened specimens, was carried out. The study showed that the value of the prestressing level had a considerable impact on the performance of hanger mechanism in relation to crack pattern, ultimate loads, cracking behavior, load–deflection, strains, and ductility. The experimental results indicated that the suggested method for strengthening inverted T-beams had efficacy in reducing the seriousness of the non-ductile hanger failure and resulted in a strength increase of up to 53% when compared to that of the un-strengthened specimen. Additionally, two analytical models for estimating the hanger capacity and the average crack width of the strengthened RC inverted T-beams were proposed. The models that were proposed exhibited a high degree of agreement with the experimental results.

Graphical abstract

Keywords

RC bridges / inverted T-beams / strengthening / hanger failure / external prestressing

References

[1] Galal K, Sekar M. Rehabilitation of RC inverted-T girders using anchored CFRP sheets. Composites Part B: Engineering, 2008, 39(4): 604–617

[2] Cheng H T, Mohammed B S, Mustapha K N. Ultimate load analysis of pretensioned inverted T-beams with circular web openings. Frontiers of Architecture and Civil Engineering in China, 2009, 3(3): 262–271

[3] Cheng H T, Mohammed B S, Mustapha K N. Finite element analysis and structural design of pretensioned inverted T-beams with web openings. Frontiers of Architecture and Civil Engineering in China, 2009, 3(2): 148–157

[4] Park S H, Cui J, Terzioglu T, Mander J B, Birely A C, Hurlebaus S. Improving existing inverted-T bent caps for serviceability and strength by retrofitting with supplemental steel. Journal of Structural Engineering, 2022, 148(7): 04022084

[5] Kim Y J, Alqurashi A. Torsion of carbon fiber-reinforced polymer-strengthened inverted T-beams under combined loading. ACI Structural Journal, 2022, 119(1): 27–40

[6] Park S H, Cui J, Mander J B, Terzioglu T, Birely A C, Hurlebaus S. Load balancing external post-tensioning for strengthening existing inverted-T bent caps. Engineering Structures, 2022, 253: 113777

[7] Mirza S A, Furlong R W. Strength criteria for concrete inverted T-girders. Journal of Structural Engineering, 1983, 109(8): 1836–1853

[8] Raths C H. Spandrel beam behavior and design. PCI Journal, 1984, 29(2): 62–131

[9] PrestressedConcrete Institute. PCI Design Handbook: Precast and Prestressed Concrete. 8th Ed. Chicago, 2017

[10] Klein G J. Design of spandrel beams. PCI Journal, 1986, 31(5): 76–124

[11] GarberDVarney N LGomezE FBayrakO. Performance of ledges in inverted-T beams. ACI Structural Journal, 2017, 114(2)

[12] RizkallaSNafadi MLucierGZiaPKleinG. Behavior and Design of Directly Loaded L-shaped Beam Ledges. Technical report RD-16-03. 2016

[13] TransportationOfficials. Standard Specifications for Highway Bridges. Washington, D.C.: AASHTO, 2002

[14] ACI318-02 & ACI 318R-02. Building code requirements for structural concrete (ACI 318-02) and commentary (ACI 318R-02). Farmington Hills, MI: American Concrete Institute, 2002

[15] Ghallab A, Beeby A W. Factors affecting the external prestressing stress in externally strengthened prestressed concrete beams. Cement and Concrete Composites, 2005, 27(9–10): 945–957

[16] Shamsai M, Sezen H, Khaloo A. Behavior of reinforced concrete beams post-tensioned in the critical shear region. Engineering Structures, 2007, 29(7): 1465–1474

[17] Naser A F, Wang Z. Experimental monitoring of the strengthening construction of a segmental box girder bridge and field testing of external prestressing tendons anchorage. Frontiers of Structural and Civil Engineering, 2012, 6: 308–320

[18] El-Shafiey T, Atta A. Retrofitting of reinforced concrete beams in shear using external prestressing technique. Magazine of Concrete Research, 2012, 64(3): 201–211

[19] Labib E L, Dhonde H B, Hsu T T, Mo Y L. Shear design of high strength concrete prestressed girders. Frontiers of Structural and Civil Engineering, 2014, 8(4): 373–387

[20] Atta A, Khalil A. Strengthening of RC beams with opening in shear zone using external prestressing technique. Magazine of Concrete Research, 2015, 67(3): 133–144

[21] Atta A, Taman M. Innovative method for strengthening dapped-end beams using an external prestressing technique. Materials and Structures, 2015, 49(8): 3005–3019

[22] Obaydullah M, Jumaat M Z, Alengaram U J, Darain K M, Huda M N, Hosen M A. Prestressing of NSM steel strands to enhance the structural performance of prestressed concrete beams. Construction & Building Materials, 2016, 129: 289–301

[23] Xue X, Wang X, Hua X, Wu M, Wu L, Ma Z, Zhou J. Experimental investigation of the shear behavior of a concrete beam without web reinforcements using external vertical prestressing rebars. Advances in Civil Engineering, 2019, 23: 1–13

[24] Jia L, Fang Z, Guadagnini M, Pilakoutas K, Huang Z. Shear behavior of ultra-high-performance concrete beams prestressed with external carbon fiber-reinforced polymer tendons. Frontiers of Structural and Civil Engineering, 2021, 15(6): 1426–1440

[25] Tena C A, Hernández M O, Archundia A H. Strengthening of reinforced concrete prismatic and haunched beams using light jacketing. Journal of Building Engineering, 2020, 32: 101757

[26] Ojaimi M. Experimental study on shear strengthening of reinforced concrete beams using different techniques of concrete jacketing. Basrah Journal of Engineering Science, 2021, 21(2): 53–61

[27] Blikharskyy Z. RC beams strengthened by RC jacketing under load. Acta Scientiarum Polonorum Architectura, 2021, 20(1): 25–30

[28] Altin S, AnilÖ, Kara M E. Improving shear capacity of existing RC beams using external bonding of steel plates. Engineering Structures, 2005, 27(5): 781–791

[29] Mhalhal J, Al-Gasham T, Jabir H. New technique to enhance the shear performance of RC deep beams using mild steel plates. IACSIT International Journal of Engineering and Technology, 2018, 7: 86

[30] Suman P, Sarath B, Ramesh K. Strengthening of RC beams with M-sand using external bonding of steel plates. IOP Conference Series. Materials Science and Engineering, 2020, 912(6): 062035

[31] Bu L, Shi C, Song L. Consumption of carbon fiber plates in the reinforced concrete beams strengthened with CFPs. Frontiers of Architecture and Civil Engineering in China, 2007, 1(4): 393–398

[32] Gand A K, Chan T M, Mottram J T. Civil and structural engineering applications, recent trends, research and developments on pultruded fiber reinforced polymer closed sections: A review. Frontiers of Structural and Civil Engineering, 2013, 7(3): 227–244

[33] Hosen M A, Jumaat M Z, Islam A. Inclusion of CFRP-epoxy composite for end anchorage in NSM-epoxy strengthened beams. Advances in Materials Science and Engineering, 2015, 2015: 1–10

[34] Hosen M A, Jumaat M Z, Islam A. Side near surface mounted (SNSM) technique for flexural enhancement of RC beams. Materials & Design, 2015, 83: 587–597

[35] Darain K M, Jumaat M Z, Shukri A A, Obaydullah M, Huda M N, Hosen M A, Hoque N. Strengthening of RC beams using externally bonded reinforcement combined with near-surface mounted technique. Polymers, 2016, 8(7): 261

[36] Shukri A A, Hosen M A, Muhamad R, Jumaat M Z. Behaviour of precracked RC beams strengthened using the side-NSM technique. Construction & Building Materials, 2016, 123: 617–626

[37] Hosen M A, Jumaat M Z, Islam A, Salam M A, Mo K H. Side-NSM composite technique for flexural strengthening of RC beams. Computers and Concrete, 2017, 20: 439–448

[38] Hosen M A, Alengaram U J, Jumaat M Z, Sulong N R, Darain K M. Glass Fiber Reinforced Polymer (GFRP) bars for enhancing the flexural performance of RC beams using side-NSM technique. Polymers, 2017, 9(5): 180

[39] Hosen M A, Jumaat M Z, Alengaram U J, Sulong N R. CFRP strips for enhancing flexural performance of RC beams by SNSM strengthening technique. Construction & Building Materials, 2018, 165: 28–44

[40] Hosen M A, Jumaat M Z, Alengaram U J, Sulong N R, Islam A. Structural performance of lightweight concrete beams strengthened with side-externally bonded reinforcement (S-EBR) technique using CFRP fabrics. Composites. Part B, Engineering, 2019, 176: 107323

[41] Mhanna H H, Hawileh R A, Abdalla J A. Shear strengthening of reinforced concrete beams using CFRP wraps. Procedia Structural Integrity, 2019, 17: 214–221

[42] Shomali A, Mostofinejad D, Esfahani M R. Effective strain of CFRP in RC beams strengthened in shear with NSM reinforcements. Structures, 2020, 23: 635–645

[43] Kim Y J, Bumadian I. Strengthening of reinforced concrete beams using embedded carbon fiber-reinforced polymer with polyester-silica. ACI Structural Journal, 2021, 118(4): 31–43

[44] Bui L V, Nguyen P T. Shear strength model of the reinforced concrete beams with embedded through-section strengthening bars. Frontiers of Structural and Civil Engineering, 2022, 16(7): 843–857

[45] Sengun K, Arslan G. Investigation of the parameters affecting the behavior of RC beams strengthened with FRP. Frontiers of Structural and Civil Engineering, 2022, 16(6): 729–743

[46] Hosen M A, Jumaat M Z, Islam A, Al Kaaf K A, Shammas M I, Hakeem I Y, Islam M M. Potential side-NSM strengthening approach to enhance the flexural performance of RC beams: Experimental, numerical and analytical investigations. Structural Engineering and Mechanics, 2023, 85(2): 179

[47] Ghallab A H, Khafaga M A, Farouk M F, Essawy A. Shear behavior of concrete beams externally prestressed with parafil ropes. Ain Shams Engineering Journal, 2013, 4(1): 1–16

[48] Herbrand M, Classen M. Shear tests on continuous prestressed concrete beams with external prestressing. Structural Concrete, 2015, 16(3): 428–437

[49] QiJ NWang J QMaZ JTongT. Shear behavior of externally prestressed concrete beams with draped tendons. ACI Structural Journal, 2016, 113(4): 677–688

[50] Li Y, Wu M, Wang W, Xue X. Shear behavior of RC beams strengthened by external vertical prestressing rebar. Advances in Civil Engineering, 2021, 2021: 1–12

[51] Junlong Z, Dongsheng L. Shear-flexural cracking strength of RC beams with external vertical prestressing rebars: Theoretical investigation and numerical simulation. Advances in Structural Engineering, 2022, 25(3): 593–610

[52] Liu Z, Cui Y, Wang W, Cao W, Wang X, Xue X. Strengthening shear resistance of beams without web reinforcements using vertical prestressed steel bars. Advances in Materials Science and Engineering, 2022, 2022: 1–10

[53] ACI318-19 & ACI 318R-19. Building Code Requirements for Structural Concrete (ACI 318-19) and Commentary (ACI 318R-19). Farmington Hills, MI: American Concrete Institute, 2019

[54] ASTMC39/C39M-21. Standard test method for Compressive Strength of Cylindrical Concrete Specimens. West Conshohocken, PA: ASTM International, 2021

[55] ASTMC469/C469M-14. Standard Test Method for Static Modulus of Elasticity and Poisson’s Ratio of Concrete in Compression. West Conshohocken, PA: ASTM International, 2014

[56] ASTMA615/A615M-16. Standard Specification for Deformed and Plain Carbon Steel Bars for Concrete Reinforcement. West Conshohocken, PA: ASTM International, 2016

[57] Mirza S A, Furlong R W. Design of reinforced and prestressed concrete inverted T beams for bridge structures. PCI Journal, 1985, 30(4): 112–136

[58] Khalil A, Etman E, Atta A, Baraghith A, Behiry R N. The effective width in shear design of wide-shallow beams: A comparative study. KSCE Journal of Civil Engineering, 2019, 23(4): 1670–1681

[59] Afefy H M, Kassem N M, Mahmoud M H, Taher S F. Efficient strengthening of opened-joint for reinforced concrete broken slabs. Composite Structures, 2016, 136: 602–615

[60] Baraghith A, Mansour W, Behiry R N, Fayed S. Effectiveness of SHCC strips reinforced with glass fiber textile mesh layers for shear strengthening of RC beams: Experimental and numerical assessments. Construction & Building Materials, 2022, 327: 127036

[61] CEB-FIP. Model Code for Concrete Structures. Paris: European Committee for Concrete, 2010

[62] ECP203-2020. Egyptian Code for Design and Construction of Reinforced Concrete Structures. Cairo: Housing and Building National Research Center, 2020

[63] EN-1992. Code for Design of Concrete Structures. Brussels: European Committee for Standardization, 2004

[64] Witchukreangkrai E, Meutsuyoshi H, Takagi M, De Silva S. Evaluation of shear crack width in partially prestressed concrete members. Japan Concrete Institute, 2006, 28(2): 823–828

[65] de Silva S, Mutsuyoshi H, Witchukreangkrai E. Evaluation of shear crack width in I-shaped prestressed reinforced concrete beams. Journal of Advanced Concrete Technology, 2008, 6(3): 443–458

[66] Afefy H M, Baraghith A T, Hassan A, Abuzaid M K. Strengthening of shear-deficient RC beams using near surface embedded precast cement-based composite plates (PCBCPs). Engineering Structures, 2021, 244: 112765

RIGHTS & PERMISSIONS

The Author(s). This article is published with open access at link.springer.com and journal.hep.com.cn