Stabilization of weak soil using geogrid-reinforced alkali-activated blast furnace slag filling made from construction and demolition waste

Talha SARICI , Tacettin GECKIL , Bahadir OK , Huseyin Suha AKSOY

ENG. Struct. Civ. Eng ››

PDF (18699KB)
ENG. Struct. Civ. Eng ›› DOI: 10.1007/s11709-026-1377-6
RESEARCH ARTICLE
Stabilization of weak soil using geogrid-reinforced alkali-activated blast furnace slag filling made from construction and demolition waste
Author information +
History +
PDF (18699KB)

Abstract

The usage of construction and demolition waste (CDW) is limited due to problems such as their low strength and high compressibility. Therefore, the focus of this study is to evaluate the behavior of CDW as a filling material on weak soil by reinforcing it with alkali-activated (AA) blast furnace slag (BFS) and geogrid, experimentally. This study presents a systematic experimental evaluation of compaction behavior under varying water/AA and BFS ratios, quantifies unconfined compressive strength (UCS) across a range of BFS contents, and investigates the bearing capacity of fillings over weak soils, using modified Proctor, UCS, and laboratory plate load experiment (LPLE) techniques, respectively. In the LPLE program, the fill configurations included CDW, geogrid-reinforced CDW, BFS-AA-stabilized CDW, and geogrid-reinforced BFS-AA-stabilized CDW. The results revealed that the maximum UCS was attained at 20% BFS content. Moreover, the ultimate bearing capacities of geogrid-reinforced CDW, BFS-AA-stabilized CDW, and their combined system were enhanced by up to 3.3, 1.1, and 4.5 times, respectively, compared to natural aggregate fills. These findings demonstrate that the engineering performance of CDW can be markedly enhanced through hybrid chemical-mechanical stabilization, highlighting its strong potential as a sustainable alternative where both recycled material utilization and substantial bearing capacity improvement are sought.

Graphical abstract

Keywords

CDW / geogrid / AA slag / granular filling / plate loading experiment

Cite this article

Download citation ▾
Talha SARICI, Tacettin GECKIL, Bahadir OK, Huseyin Suha AKSOY. Stabilization of weak soil using geogrid-reinforced alkali-activated blast furnace slag filling made from construction and demolition waste. ENG. Struct. Civ. Eng DOI:10.1007/s11709-026-1377-6

登录浏览全文

4963

注册一个新账户 忘记密码

References

[1]

Sarici T , Ozcan R T . Interpretation of geotechnical risk maps for Malatya province in terms of earthquake sequence on February 6, 2023. Environmental Earth Sciences, 2025, 84(3): 91

[2]

Sarici T , Ozcan R T . Evaluation of geotechnical properties of Doğanşehir district with geographical information systems after the February 6, 2023 earthquakes. Journal of Seismology, 2024, 28(6): 1421–1444

[3]

Ok B , Sarici T , Talaslioglu T , Yildiz A . Geotechnical properties of recycled construction and demolition materials for filling applications. Transportation Geotechnics, 2020, 24: 100380

[4]

Ozcelikci E , Ozdogru E , Tugluca M S , Ilcan H , Sahmaran M . Comprehensive investigation of performance of construction and demolition waste based wood fiber reinforced geopolymer composites. Journal of Building Engineering, 2024, 84: 108682

[5]

Mir B A . Smart materials and their applications in civil engineering: An overview. International Journal of Civil Engineering and Construction Science, 2017, 4(2): 11–20

[6]

Alhawamdeh M , Ferriz-Papi J A , Lee A . Examining the drivers to support improved construction and demolition waste management for a circular economy: A comprehensive review using a systematic approach. Sustainability, 2024, 16: 6014

[7]

Mahpour A . Prioritizing barriers to adopt circular economy in construction and demolition waste management. Resources, Conservation and Recycling, 2018, 134: 216–227

[8]

Sarici T , Geckil T , Ok B , Aksoy H S . An investigation of the usability of alkali-activated blast furnace slag-additive construction demolition waste as filling material. Materials, 2025, 18(2): 398

[9]

OECD. Global Material Resources Outlook to 2060. Paris: OECD. 2019, doi: 10.1787/9789264307452-en

[10]

United Nations Environment Programme. 2021 Global Status Report for Buildings and Construction. 2021

[11]

Yaghoubi E , Ghorbani B , Saberian M , van Staden R , Guerrieri M , Fragomeni S . Strength and resilient modulus characteristics of emulsion-stabilised demolition wastes in pavement structures. Journal of Building Engineering, 2024, 82: 108257

[12]

Sarici T. Evaluation of Usability of Pozzolan Reinforced Construction and Demolition Wastes as A Granular Fill. Dissertation for the Doctoral Degree. Malatya: Inonu University, 2019

[13]

Bordoloi S , Afolayan O D , Ng C W W . Feasibility of construction demolition waste for unexplored geotechnical and geo-environmental applications—A review. Construction and Building Materials, 2022, 356: 129230

[14]

Gao Y , Wang J Y , Xu X X . Machine learning in construction and demolition waste management: Progress, challenges, and future directions. Automation in Construction, 2024, 162: 105380

[15]

Doan T , Arulrajah A , Lin Y L , Horpibulsuk S , Chu J , Darmawan S . Chemical stabilization of demolition wastes in pavement bases using one-part fly ash and slag based geopolymers. Transportation Geotechnics, 2024, 45: 101192

[16]

Prashad D , Shubham K , Metya S , Singh R P . Performance of combined construction and demolition waste with marginal soil as backfill in MSE walls. Transportation Infrastructure Geotechnology, 2025, 12(7): 262

[17]

Sharma A , Shrivastava N . Settlement behavior of recycled construction and demolition waste aggregates with sandy soil by performing laboratory model plate load test. Transportation Infrastructure Geotechnology, 2024, 11(1): 303–326

[18]

Shiva Bhushan J Y V , Parhi P S , Umashankar B . Geotechnical characterization of construction and demolished (C&D) waste. Stalin V, Muttharam M, eds. Geotechnical Characterisation and Geoenvironmental Engineering, 2019, 27–34

[19]

Corrales L A G , Pierozan R C , Araújo G L S , Palmeira E M . Evaluation of construction and demolition waste and other alternative fills for strip-reinforced soil walls. Sustainability, 2023, 15(12): 9705

[20]

Bassani M , Tefa L , Russo A , Palmero P . Alkali-activation of recycled construction and demolition waste aggregate with no added binder. Construction and Building Materials, 2019, 205: 398–413

[21]

Geckil T , Sarici T , Aksoy H S . The usability of construction and demolition wastes stabilized using alkali activated fly ash as filler material. Revista de la Construcción, 2025, 24(2): 428–448

[22]

Arulrajah A , Mohammadinia A , Phummiphan I , Horpibulsuk S , Samingthong W . Stabilization of recycled demolition aggregates by geopolymers comprising calcium carbide residue, fly ash and slag precursors. Construction and Building Materials, 2016, 114: 864–873

[23]

Arulrajah A , Mohammadinia A , Horpibulsuk S , Samingthong W . Influence of class F fly ash and curing temperature on strength development of fly ash-recycled concrete aggregate blends. Construction and Building Materials, 2016, 127: 743–750

[24]

Udomchai A , Hoy M , Suddeepong A , Phuangsombat A , Horpibulsuk S , Arulrajah A , Thanh N C . Generalized interface shear strength equation for recycled materials reinforced with geogrids. Sustainability, 2021, 13(16): 9446

[25]

Silvestre G R , Fleury M P , da Silva J L , Santos E C G . Use of recycled construction and demolition waste (RCDW) in geosynthetic-reinforced roadways: Influence of saturation condition on geogrid mechanical properties. Sustainability, 2023, 15(12): 9663

[26]

Rahman M A , Arulrajah A , Piratheepan J , Bo M W , Imteaz M A . Resilient modulus and permanent deformation responses of geogrid-reinforced construction and demolition materials. Journal of Materials in Civil Engineering, 2014, 26(3): 512–519

[27]

Arulrajah A , Rahman M A , Piratheepan J , Bo M W , Imteaz M A . Evaluation of interface shear strength properties of geogrid-reinforced construction and demolition materials using a modified large-scale direct shear testing apparatus. Journal of Materials in Civil Engineering, 2014, 26(5): 974–982

[28]

Sarıcı T , Ok B , Mert A , Comez S . The resilient modulus of hybrid construction and demolition wastes reinforced by a geogrid. Acta Geotechnica Slovenica, 2022, 19(2): 1–13

[29]

Santos E C G , Palmeira E M , Bathurst R J . Behaviour of a geogrid reinforced wall built with recycled construction and demolition waste backfill on a collapsible foundation. Geotextiles and Geomembranes, 2013, 39: 9–19

[30]

Santos E C G , Palmeira E M , Bathurst R J . Performance of two geosynthetic reinforced walls with recycled construction waste backfill and constructed on collapsible ground. Geosynthetics International, 2014, 21(4): 256–269

[31]

Packrisamy K , Jayakumar K . Fly ash and ceramic tile industrials waste: Landfills to construction materials. Clean Technologies and Environmental Policy, 2023, 25(10): 3247–3261

[32]

Fořt J , Mildner M , Keppert M , Pommer V , Černý R . Experimental and environmental analysis of high-strength geopolymer based on waste bricks and blast furnace slag. Polymers, 2023, 15(14): 3092

[33]

Xue Y X , Arulrajah A , Horpibulsuk S , Chu J . Strength and stiffness performance of geopolymer stabilized washed recycled sands derived from demolition wastes in pavement subgrades. Construction and Building Materials, 2023, 369: 130618

[34]

Jewell R A . Material properties for the design of geotextile reinforced slopes. Geotextiles and Geomembranes, 1985, 2(2): 83–109

[35]

Jewell R A, Paine N, Woods R I. Design methods for steep reinforced embankments. In: Polymer Grid Reinforcement. London: Thomas Telford Limited, 1984, 70–81

[36]

Webster S L. Geogrid Reinforced Base Courses for Flexible Pavements for Light Aircraft: Test Section Construction, Behavior Under Traffic, Laboratory Tests, and Design Criteria. DOT/FAA/RD-92/25. 1992

[37]

Mir B A , Gulzar S M , Wani K M N S . Geotechnical performance of geogrid-reinforced subgrades for flexible pavement systems in the Himalayan region. Transportation Infrastructure Geotechnology, 2025, 12(4): 130

[38]

Akbar A , Bhat J A , Mir B A . Experimental investigation of a reduced-scale square footing model on the geocomposite reinforced layered soil. Indian Geotechnical Journal, 2023, 53(4): 887–903

[39]

Akbar A , Bhat J A , Mir B A . Laboratory study on pressure settlement behavior of shallow foundation on bitumen coated geogrid reinforced soil bed with varying percentage of prestress. International Journal of Pavement Research and Technology, 2023, 16(3): 544–562

[40]

Akbar A , Bhat J A , Mir B A . Plate load tests for investigation of the load–settlement behaviour of shallow foundation on bitumen-coated geogrid reinforced soil bed. Innovative Infrastructure Solutions, 2021, 6(2): 80

[41]

Han J , Thakur J K . Sustainable roadway construction using recycled aggregates with geosynthetics. Sustainable Cities and Society, 2015, 14: 342–350

[42]

Ok B , Sarici T , Demir A , Talaslioglu T , Yildiz A . Investigation of construction and demolition materials reinforced by geosynthetics. Proceedings of the Institution of Civil Engineers-Engineering Sustainability, 2023, 176(5): 285–298

[43]

Jallu M , Arulrajah A , Saride S , Evans R . Flexural fatigue behavior of fly ash geopolymer stabilized-geogrid reinforced RAP bases. Construction and Building Materials, 2020, 254: 119263

[44]

Vieira C S , Pereira P M . Short-term tensile behaviour of three geosynthetics after exposure to recycled construction and demolition materials. Construction and Building Materials, 2021, 273: 122031

[45]

Kommanamanchi V , Mahopatra P K , Duddu S R , Mutha A , Chennarapu H . Large-scale direct shear testing for assessing interfacial parameters of natural and recycled sand with geosynthetic reinforcements. Construction and Building Materials, 2024, 442: 137598

[46]

BS EN 933-11:2009. Tests for Geometrical Properties of Aggregates—Part 11: Classification Test for the Constituents of Coarse Recycled Aggregate. London: British Standards Institution, 2009

[47]

ASTM C136-06. Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates. West Conshohocken, PA: ASTM, 2006

[48]

ASTM C127-12. Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate. West Conshohocken, PA: ASTM, 2012

[49]

ASTM C128-12. Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate. West Conshohocken, PA: ASTM, 2012

[50]

ASTM D1557-12. Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3)). West Conshohocken, PA: ASTM, 2012

[51]

ASTM D1883-14. Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils. West Conshohocken, PA: ASTM, 2016

[52]

BS EN 933-3:2012. Tests for Geometrical Properties of Aggregates-Determination of Particle Shape. Flakiness Index. London: British Standards Institution, 2012

[53]

ASTM C131-06. Standard Test Method for Resistance to Degradation of Small-size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine. West Conshohocken, PA: ASTM, 2006

[54]

ASTM D2487-11. Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System). West Conshohocken, PA: ASTM, 2011

[55]

ASTM D854-10. Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer. West Conshohocken, PA: ASTM, 2010

[56]

ASTM D4318-17. Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils. West Conshohocken, PA: ASTM, 2017

[57]

ASTM D698-12. Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kN-m/m3)). West Conshohocken, PA: ASTM, 2012

[58]

ASTM D2166-06. Standard Test Method for Unconfined Compressive Strength of Cohesive Soil. West Conshohocken, PA: ASTM, 2006

[59]

Phoo-ngernkham T , Maegawa A , Mishima N , Hatanaka S , Chindaprasirt P . Effects of sodium hydroxide and sodium silicate solutions on compressive and shear bond strengths of FA–GBFS geopolymer. Construction and Building Materials, 2015, 91: 1–8

[60]

Memon A H , Radin S S , Zain M F M , Trottier J F . Effects of mineral and chemical admixtures on high-strength concrete in seawater. Cement and Concrete Research, 2002, 32(3): 373–377

[61]

ASTM D1633-17. Standard Test Methods for Compressive Strength of Molded Soil–cement Cylinders. West Conshohocken, PA: ASTM, 2017

[62]

ASTM D5102-09. Standard Test Method for Unconfined Compressive Strength of Compacted Soil-lime Mixtures. West Conshohocken, PA: ASTM, 2009

[63]

Binquet J , Lee K L . Bearing capacity analysis of reinforced earth slabs. Journal of the Geotechnical Engineering Division, 1975, 101(12): 1257–1276

[64]

TxDOT. Test Procedure for Soil-Cement Testing. Tex-120-E. 2013

[65]

VicRoads. Cementitious Treated Crushed Rock for Pavement Subbase. VicRoads Section 815. 2013

[66]

Ok B. Investigation of the Behaviour Under Static and Cyclic Loading of Construction and Demolition Waste Embankment Reinforced with Geosynthetics. Dissertation for the Doctoral Degree. Adana, Turkey: Çukurova University, 2018

[67]

Örnek M. Geogrid Reinforcement of Soft Clay Deposits. Dissertation for the Doctoral Degree. Adana, Turkey: Çukurova University, 2009

[68]

Briaud J L, Jeanjean P. Load settlement curve method for spread footings of sand. In: Vertical and Horizontal Deformations of Foundations and Embankments. College Station, TX: ASCE, 1994, 1774–1804

[69]

Allison P. When Can You Safely Ignore Multicollinearity? Available online (accessed on 2012)

[70]

Provis J L. . Geopolymers and other alkali activated materials: Why, how, and what?. Materials and Structures, 2014, 47(1–2): 11–25

[71]

Kandalai S , Patel A . Alkali activation of red mud and GGBS blends for expansive soil stabilization: Strength, durability and leachate studies. Indian Geotechnical Journal, 2026, 56(2): 598–623

[72]

John N J , Wanjari S , Patel A . Effects of particle shape and size on strength and durability of recycled concrete aggregates: An experimental and statistical approach. Construction and Building Materials, 2025, 483: 141718

[73]

John N J , Khan I , Patel A . Evaluation of the crushing characteristics of industrial waste aggregates as construction materials. Construction and Building Materials, 2023, 403: 133111

[74]

John N J , Wanjari S , Patel A . Enhancing durability of recycled concrete and brick aggregates with silica fume treatment. Road Materials and Pavement Design, 2026, 27(6): 1728–1764

Rights & permissions

Higher Education Press

PDF (18699KB)

0

Accesses

0

Citation

Detail

Sections
Recommended

/

〈 〉