Analysis of the effect of steam injection conditions on the integrity of casing-cement sheath-formation assemblies in heavy oil thermal recovery

Abstract

Accurately forecasting the sealing failure behavior of the casing-cement sheath-formation assembly under various steam injection operational parameters and cyclic steam stimulation conditions remains challenging. Such unpredictability heightens the risk of seal integrity compromise in the wellbores of thermal heavy oil production. This paper develops a numerical simulation and analytical approach based on heat-fluid-solid interactions within the casing-cement sheath-formation system. It assesses the impact of potential cement sheath and interfacial failures in response to differing steam injection pressures, temperatures, injection rates, and cyclic steam volumes. This assessment leverages the established relationships between the temperature-dependent elastic modulus and Poisson’s ratio of cementitious materials, as well as the dynamics of wellbore pressure, temperature, and steam quality during steam injection. Experimental findings suggest that maintaining steam injection temperatures between 340 ℃ and 380 ℃ can effectively mitigate the risk of shear-induced damage and enhance the safety of the cementing interface. The injection rate appears to have a minimal impact on interface integrity. The extent of plastic strain in the cement sheath is proportionate to the size of the micro-annular gap at the interface. When the initial formation has an elastic modulus of 15 GPa, variations in the cement sheath’s elastic modulus do not influence the micro-annular gap size. However, in formations with an initial elastic modulus of 5 GPa, a lower elastic modulus of the cement sheath corresponds to a smaller micro-annular gap. The study concludes that a higher initial geostress and temperature, coupled with a high elastic modulus of the surrounding strata, are conducive to maintaining the integrity of the cement sheath interface.

Keywords

Heavy oil thermal recovery / steam injection conditions / Casing-cement sheath-formation assemblies / Heat-fluid-solid coupling model / Cement sheath failure analysis

CRediT authorship contribution statement

Fuquan Ding: Writing – review & editing, Writing – original draft, Software, Resources, Data curation. Huajie Liu: Writing – review & editing, Resources, Data curation. Zhongguang Liu: Writing – original draft, Supervision, Methodology. Yuhuan Bu: Writing – review & editing, Resources, Project administration, Funding acquisition. Hongxu Zhang: Project administration, Formal analysis. Hui Yin: Project administration, Formal analysis.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

References

[1] Huanquan Sun , Huiqing Liu , Haitao Wang , et al. , Development technology and direction of China’s thick oil thermal recovery, J. Petrol. 43 (11) (2022) 1664-1674.

[2] S. Ghabezloo, Micromechanics analysis of thermal expansion and thermal pressurisation of a hardened cement paste, Cement Concr. Res. 41 (5) (2011).

[3] Standard D-010 Well Integrity in Drilling and Well Operations. Norway: NORSOK, 2013.

[4] Zhi Zhang , Yanjun Zhou , Jianhong Fu , et al. , Wellbore integrity design methodology for sulphur-containing gas wells, Nat. Gas. Ind. 30 (3) (2010) 67-69.

[5] R.E. Zinkham , R.J. Goodwin , Burst resistance of pipe cemented into the earth, J. Petrol. Technol. 14 (9) (1962) 1033-1040.

[6] Pinglin Liu , Mechanical damage of cemented rings in oil wells, J. Jianghan Petrol. Inst. 15 (2) (1993) 55-59.

[7] M. Thiercelin, C. Baumgarte, D. Guillot, A Soil Mechanics Approach to Predict Cement Sheath Behaviour, 1998. SPE47375.

[8] M. Bosma, K. Ravi, D.W. Van , et al. , Design approach to sealant selection for the life of the well. Design approach to sealant selection for the life of the well, in: Proceedings of the Society of Petroleum, 1999, pp. 15-24. USA: PSP.

[9] A.J. Philippacopoulos , M.L. Berndt , Mechanical Response and Characterisation of Well Cements, 2002. SPE77755.

[10] J. Saint-Marc, A. Garnier, A.P. Bois, Initial State of Stress: the Key to Achieving long-term cement-sheath Integrity, 2008. SPE116651.

[11] K.E. Gray , E. Podnos , E. Becker , Finite-Element Studies of near-wellbore Region During Cementing Operations: Part I, 2009. SPE106998.

[12] L.I. Jing , Chengyan Lin , Shaochun Yang , et al. , Theoretical solution of thermal stress in casing-cement ring-stratum coupling system, J. China Univ. Petrol. 36 (2) (2009) 63-68.

[13] Xinyang Guo , Yuhuan Bu , L.I. Juan , et al. , Failure mode of cementing ring and its preventive measures under complex downhole conditions, Nat. Gas. Ind. 33 (11) (2013) 86-91.

[14] Jun Yuan , Jin Feng , Huawei Liu , et al. , Analytical solution and finite element analysis of mechanical model of casing-cement ring-strata integrity system, J. Changjiang Univ. Nat. Sci. Edit.: Sci. Eng. (Early) 12 (1) (2015) 52-56.

[15] Z.Q. Wu, Y. Wu, J.P. Yue, et al., Study on the effect of heat stabilizers on the integrity of cement sheath under ultra-high temperature conditions, J. Chongqing Univ. Sci. Technol. (Nat. Sci. Edit.) 23 (5) (2021) 48-52+58, https://doi.org/10.19406/j.cnki.cqkjxyxbzkb.2021.05.010.

[16] Y. Bu, S. Shen, Z. Liu, et al., Establishment and application of T-H-M coupling model of casing-cement ring-formation in thermal recovery Wells, Arabian J. Sci. Eng. (2022) 1-13, https://doi.org/10.1007/s13369-022-07069-w.

[17] S. Zhao, Analysis on integrity of cement sheath for ultra-deep well cementing based on ABAQUS, Petrol. Chem. Equip. 28 (6) (2025) 142-145.

[18] Y. Yan, X.B. Liu, J.L. Li, et al., Numerical simulation on sealing integrity of perforated cement sheath during staged fracturing, Sci. Technol. Eng. 23 (23) (2023) 9903-9910.

[19] X. Yan, Y. Yao, X.L. Guo, J. Li, Y.D. Tian, G.H. Liu, Failure evaluation mechanism of cement sheath sealing integrity under casing eccentricity during multistage fracturing, Pet. Sci. 21 (5) (2024) 3428-3445.

[20] K.H. Deng , N.T. Zhou , Y.H. Lin , et al. , Failure mechanism and control method of cement sheath sealing integrity under alternating thermal-stress coupling in geothermal wells, Renew. Energy 226 (2024) 120448.

[21] Y.P. Cao , H. Du , G. Chen , et al. , Analysis on the influence of cement sheath loss on casing strength under thermal-solid coupling, Mech. Electr. Eng. Technol. 54 (2) (2025) 93-99.

[22] K. Mogi, Experimental Rock Mechanics, CRC Press, London, 2007.

[23] P.B. Jackson , C.E. Mmphey , Effect of Casing Pressure on Gas Flow Through a Sheath of Set Cement, 1993. SPE25698.

[24] K.J. Goodwin , R.J. Crook , Cement Sheath Stress Failure, 1992. SPE20453.

[25] B.H. Dale , P.B. James , A study of two-phase flow in inclined pipes, J. Petrol. Technol. 25 (5) (1973) 607-617.

[26] B.A. Eaton , E.A. Donald , R.K. Charles , The prediction of flow patterns, liquid holdup and pressure losses occurring during continuous tow-phase flow in horizontal pipelines, J. Petrol. Technol. 67 (1) (1967) 815-828.

[27] G.L. Kalousek , The Reactions of Cement Hydration at Elevated Temperatures, 1952.

[28] Luo Yang , Dajun Chen , Shui Yin , Research on high temperature steam throughput resistant cementing mud system, Drill. Complet. Fluid. 26 (5) (2009) 50-54.

[29] Ying Zhang , Dajun Chen , Yang Luo , Indoor test on the effect of silica sand on the strength of cementite in heavy oil thermal recovery wells, Oil Drill. Proc. 32 (5) (2010) 44-47.

[30] G. Benge, Cement designs for high-rate acid gas injection wells, Int. Petrol. Technol. Conf. Doha: IPTC (2005) 21-23.

[31] M.A. Cong , Bu Yuhuan , Zhao Shaobiao , et al. , Experimental study on the modification of aluminates cement for cementing, J. Constr. Mater. 18 (1) (2015) 100-106.

[32] T. Sugama, L.E. Brothers, T.R. Van de Puttee, Air-foamed calcium aluminate phosphate cement for geothermal wells, Cement Concr. Compos. 27 (7) (2005) 758-768.

[33] Hao Zhang , Houming Li , Junfang Fu , et al. , Research status and development trend of cement slurry technology for heavy oil thermal recovery, Inner Mongolia Petrochem. Industr. 40 (22) (2014) 107-109.

[34] Zhao Xiaofeng , Zhichuan Guan , Hualin Liao , et al. , Mechanism and calculation method of micro-annular gap generation at cementing interface, J. China Univ. Petrol. (Nat. Sci. Edit.) 41 (5) (2017) 94-101.