Reconstruction and prediction of capillary pressure curve based on Particle Swarm Optimization-Back Propagation Neural Network method

Abstract

Capillary pressure curve plays a critical role in the reservoir evaluation. It is essential to reconstruct and predict capillary pressure curve properly. Many traditional capillary pressure correlations have been suggested in the literature. However, their major limitation is mainly applicable to homogenous reservoir, and the larger error will be caused when heterogeneous reservoir is dealt by using these mathematical correlations. This study aims at providing an important method based on Particle Swarm Optimization-Back Propagation Neural Network (PSO-BP neural network) to represent and predict capillary pressure curve for homogenous and heterogeneous reservoir. The combination of PSO algorithm and BP neural network converges quickly, which improves the accuracy and efficiency of simulation. In this paper, core samples from three blocks of the same marine-sand reservoir, whose porosity is between 0.6% and 20.0% and permeability is between 0.1mD and 6117mD, are investigated by PSO-BP neural network method and J-Function method respectively. The reconstruction and prediction results are compared with the results obtained by mercury intrusion method in laboratory. The results show that capillary pressure curves reconstructed and predicted by PSO-BP neural network method are in better agreement with mercury intrusion curves than J-Function method, with 0.1%-5% and 5%-8% relative error respectively, which can totally meet the in-situ requirements. It is also demonstrated that PSO-BP neural network method is more suitable for homogenous and heterogeneous reservoir.

Keywords

Capillary pressure curve / Homogenous reservoir / Heterogeneous reservoir / PSO-BP neural network / Mercury intrusion

Acknowledgments

The Authors gratefully acknowledge the financial support from the Open Fund (PLN201614) of State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation (Southwest Petroleum University), and Young Scholars Development Fund of Southwest Petroleum University (Grant No.201599010086).

References

[1] W.A. Bruce, H.J. Welge, The restored-state method for determination of oil in place and connate water, in:Drilling and Production Practice, New York, 1 January, API, 1947, pp. 47e166.

[2] J.M. Dumore, R.S. Schols, Drainage capillary-pressure functions and the influence of connate water, SPE J. 14 (5) (1974) 437-444. SPE-4096-PA, https://doi.org/10.2118/4096-PA.

[3] M. Fleury, D. Longeron, Combined resistivity and capillary pressure measurements using micropore membrane technique, J. Pet. Sci. Eng 19 (1-2) (1998) 73-79. https://doi.org/10.1016/S0920-4105(97)00037-5.

[4] W.R. Purcell, Capillary pressures-their measurement using mercury and the caculation of permeability therefrom, J. Pet. Technol. 1 (02) (1949) 39-48. SPE-949039-G, https://doi.org/10.2118/949039-G.

[5] C.D. Tsakirogloua, A.C. Payatakesa, Mercury intrusion and retraction in model porous media, Adv. Colloid Interface Sci. 75 (75) (1998) 215-253. https://doi.org/10.1016/S0001-8686(98)00057-058.

[6] R.L. Slobod, A. Chambers,W.L. Prehn Jr., Use of centrifuge for determining connate water, residual oil, and capillary pressure curves of small core samples, J. Pet. Technol 3 (04) (1951) 127-134. SPE-951127-G, https://doi.org/10.2118/951127-G.

[7] K.G. Ayappa, H.T. Davis, E.A. Davis, Gordon J. Capillary pressure: centrifuge method revisited, AIChE J. 35 (3) (1989) 365-372, https://doi.org/10.1002/aic.690350304.

[8] Z.A. Chen, D.W. Ruth, Centrifuge capillary pressure data reduction with a modified Forbes method, J. Pet. Sci. Eng 9 (4) (1993) 303-312. https://doi.org/10.1016/0920-4105(93)90061-I.

[9] A.O. Ajufo, D.H. Daneshjou, J.D. Warne,Capillary pressure characteristics at overburden pressure using the centrifuge method, in:Presented at the SPE Gas Technology Symposium, Calgary, Alberta, Canada, 28-30 June, 1993. SPE-26148-MS, https://doi.org/10.2118/26148-MS.

[10] S. Karimi, H. Kazemi,Capillary pressure measurement using reservoir fluids in a middle Bakken core, in:Presented at the SPE Western Regional Meeting, Garden Grove, California, USA, 27-30 April, 2015. SPE-174065-MS, https://doi.org/10.2118/174065-MS.

[11] D. Longeron, W.L. Hammervold, S.M. Skjaeveland,Water-oil capillary pressure and wettability measurements using micropore membrane technique, in:Presented at the International Meeting on Petroleum Engineering, Beijing, China, 14-17 November, 1995. SPE-30006-MS, https://doi.org/10.2118/30006-MS.

[12] S. Wang, T.K. Tokunaga, Capillary pressure-saturation relations for supercritical CO₂ and brine in limestone/dolomite sands: implications for geologic carbon sequestration in carbonate reservoirs, Environ. Sci. Technol. 49 (12) (2015) 7208-7217, https://doi.org/10.1021/acs.est.5b00826.

[13] J.M. Lombard, P. Egermann, R. Lenormand, Measurement of capillary pressure curves at reservoir conditions, in: Presented at the International Symposium of the SCA, Monterey, USA, 2002. SCA2002-S2009.

[14] O.A. Alomair, New experimental approach for measuring drainage and spontaneous imbibition capillary pressure, Energy Fuels 23 (1) (2009) 260-271, https://doi.org/10.1021/ef800394v.

[15] M. Leverett, Capillary behavior in porous solids, Trans. AIME 142 (01) (1941) 152-169, https://doi.org/10.2118/941152-G.

[16] R.H. Brooks, A.T. Corey, Properties of porous media affecting fluid flow, J. Irrig. Drain. Div 92 (2) (1966) 61-88.

[17] R.D. Evans, A water-gas relative permeability relationship for tight gas sand reservoirs, J. Energy Resour. Technol. 112 (4) (1990) 239-245, https://doi.org/10.1115/1.2905766.

[18] Z.I. Khatib, G.J. Hirasaki, A.H. Falls, Effects of capillary pressure on coalescence and phase mobilities in foams flowing through porous media, SPE Reserv. Eng 3 (3) (1985) 919-926, https://doi.org/10.2118/15442-PA.

[19] R.F. Sigal, Mercury capillary pressure measurements on Barnett core, SPE Reservoir Eval. Eng. 16 (4) (2013) 432-442. SPE-167607-PA, https://doi.org/10.2118/167607-PA.

[20] D.C. Standnes, Estimation of imbibition capillary pressure curves from spontaneous imbibition data, Energy Fuels 24 (2) (2009) 1081-1087, https://doi.org/10.1021/ef900938h.

[21] T. Gang, M.G. Kelkar,A more general capillary pressure curve and its estimation from production data, in:Presented at the Rocky Mountain Oil & Gas Technology Symposium, Denver, Colorado, U.S.A., 16-18 April, 2007. SPE-108180-MS, https://doi.org/10.2118/108180-MS.

[22] R.F. Angulo, V. Alvarado, H. Gonzalez,Fractal dimensions from mercury intrusion capillary tests, in:Presented at the SPE Latin America Petroleum Engineering Conference, March, Caracas, Venezuela, 8-11 March, 1992. SPE-23695-MS, https://doi.org/10.2118/23695-MS.

[23] K. Li,Generalized capillary pressure and relative permeability model inferred from fractal characterization of porous media, in:Presented at the SPE Annual Technical Conference and Exhibition, Houston, Texas, 26-29 September, 2004. SPE-89874-MS, https://doi.org/10.2118/89874-MS.

[24] J. Lai, G. Wang, Fractal analysis of tight gas sandstones using high-pressure mercury intrusion techniques, J. Nat. Gas Sci. Eng. 24 (2015) 185-196, https://doi.org/10.1016/j.jngse.2015.03.027.

[25] R. Farajzadeh, M. Lotfollahi, A.A. Eftekhari, W.R. Rossen, G.J. Hirasaki, Effect of permeability on implicit-texture foam model parameters and the limiting capillary pressure, Energy Fuels 29 (5) (2015) 3011-3018, https://doi.org/10.1021/acs.energyfuels.5b00248.

[26] E.C. Kumbur, K.V. Sharp, M.M. Mench, A design tool for predicting the capillary transport characteristics of fuel cell diffusion media using an artificial neural network, J. Power Sources 176 (1) (2008) 191-199. https://doi.org/10.1016/j.jpowsour.2007.10.059.

[27] N. Golsanami, A. Kadkhodaie-Ilkhchi, A. Erfani, Synthesis of capillary pressure curves from post-stack seismic data with the use of intelligent estimators: a case study from the iranian part of the south pars gas field, Persian gulf basin, J. Appl. Geophys. 112 (2015) 215-225. https://doi.org/10.1016/j.jappgeo.2014.11.013.

[28] J. Hofman, W. Slijkermail, W. Looyestijn, Y. Volokitin, Constructing capillary pressure curves from NMR log data in the presence of hydrocarbons, in: Presented at the SPWLA 40th Annual Logging Symposium, Oslo, Norway, 30 May-3 June, 1999. SPWLA-1999-KKK.

[29] M. Altunbay, R. Martain, M. Robinson,Capillary pressure data from NMR logs and its implications on field economics, in:Presented at the SPE Annual Technical Conference and Exhibition, New Orleans, Louisiana, 30 September-3 October, 2001. SPE-71703-MS, https://doi.org/10.2118/71703-MS.

[30] C. Zhang, L. Xiao, Z.Q. Mao, Z.C. Sun, X.P. Luo, A novel method to construct capillary pressure curves by using NMR log data and its application in reservoir evaluation, in: Presented at the Kuwait International Petroleum Conference and Exhibition, Kuwait City, Kuwait, 3e5 December, 2009. IPTC-11863-MS, https://doi.org/10.2523/IPTC-11863-MS.

[31] Y. Yao, D. Liu, Comparison of low-field NMR and mercury intrusion porosimetry in characterizing pore size distributions of coals, Fuel 95 (1) (2012) 152-158. https://doi.org/10.1016/j.fuel.2011.12.039.

[32] M. Eslami, A. Kadkhodaie-Ilkhchi, Y. Sharghi, N. Golsanami, Construction of synthetic capillary pressure curves from the joint use of NMR log data and conventional well logs, J. Pet. Sci. Eng 111 (2013) 50-58. https://doi.org/10.1016/j.petrol.2013.10.010.

[33] L. Xiao, C.C. Zou, Z.Q. Mao, Y. Jin, J.C. Zhu, A new technique for synthetizing capillary pressure (Pc) curves using NMR logs in tight gas sandstone reservoirs, J. Pet. Sci. Eng. 145 (2016) 493-501. https://doi.org/10.1016/j.petrol.2016.06.002.

[34] H.W. Brown, Capillary pressure investigations, J. Pet. Technol 3 (03) (1951) 67-74, https://doi.org/10.2118/9510 67-G.

[35] J.L. McClelland, D.E. Rumelhart, A distributed model of human learning and memory, in: Parallel Distributed Processing, Mit Press, 1986, pp. 170e215.

[36] D.E. Rumelhart, P. Smolensky, J.L. McClelland, G. Hinton, 2 Mit Press, Sequential Thought Processes in PDP Models vol. 1986, pp. 3e57.

[37] R.C. Eberhart, J. Kennedy,A new optimizer using particle swarm theory, in:Presented at the Proceedings of the Sixth International Symposium on Micro Machine and Human Science, IEEE, vol. 1, 1995, pp. 39-43, https://doi.org/10.1109/MHS.1995.494215.

[38] J.L. Baldwin, D.N. Otte, C.L. Whealtley,Computer emulation of human mental processes: application of neural network simulators to problems in well log interpretation,in:Presented at the SPE Annual Technical Conference and Exhibition, San Antonio, Texas, 8-11 October, 1989. SPE-19619-MS, https://doi.org/10.2118/19619-MS.

[39] S.D. Mohaghegh, C. Goddard, A. Popa, S. Ameri, M. Bhuiyan,Reservoir characterization through synthetic logs, in:Presented at the SPE Eastern Regional Meeting, Morgantown, West Virginia, 17-19 October, 2000. SPE-65675-MS, https://doi.org/10.2118/65675-MS.

[40] H.B. Helle, A. Bhatt, B. Ursin, Porosity and permeability prediction from wireline logs using artificial neural networks: a North Sea case study, Geophys. Procpect. 49 (4) (2001) 431-444, https://doi.org/10.1046/j.1365-2478.2001.00271.x.

[41] F.N. Desai, A.H. Demond, K.F. Hayes, Influence of surfactant sorption on capillary pressure-saturation relationships, Ground Water 78 (21) (1991) 133-148, https://doi.org/10.1021/bk-1992-0491.ch011.

[42] S.A. Bradford, F.J. Leij, Wettability effects on scaling two-and three-fluid capillary pressure-saturation relations, Environ. Sci. Technol. 29 (6) (1995) 1446-1455. https://doi.org/10.1016/0169-7722(95)00027-S.

[43] P.C. Reeves, M.A. Celia, A functional relationship between capillary pressure, saturation, and interfacial area as revealed by a pore-scale network model, Water Resour. Res. 32 (8) (1996) 2345-2358. https://doi.org/10.1016/S0301-9322(97)80174-7.

[44] R.J. Held, M.A. Celia, Modeling support of functional relationships between capillary pressure, saturation, interfacial area and common lines, Adv. Water Resour. 24 (3-4) (2001) 325-343. https://doi.org/10.1016/S0309-1708(00)00060-9.

[45] G.E. Archie, Introduction to petrophysics of reservoir rocks, AAPG Bull. 34 (34) (1950) 943-961, https://doi.org/10.1306/3D933F62-16B1-11D7-8645000102C1865D.

[46] J.H.M. Thomeer, Introduction of a pore geometrical factor defined by the capillary pressure curve, J. Pet. Technol 12 (3) (1960) 73-77, https://doi.org/10.2118/1324-G.

[47] J.B. Jennings, Capillary pressure techniques: application to exploration and development geology, AAPG Bull. 71 (10) (1987) 1196-1209, https://doi.org/10.1306/703C8047-1707-11D7-8645000102C1865D.

[48] R. Poli, J. Kennedy, T. Blackwell, Particle swarm optimization, Swarm Intell 1 (1) (2007) 33-57, https://doi.org/10.1007/s11721-007-0002-0. Source: DBLP.

[49] J. Kennedy, Particle swarm optimization, in: Encyclopedia of Mahine Learning, 2011, pp. 760e766.

[50] D.C. Beard, P.K. Weyl, Influence of texture on porosity and permeability of unconsolidated sand, AAPG Bull. 57 (2) (1973) 349-369.

[51] K.J. Hsu, Studies of ventura field, California: i, facies geometry and genesis of lower pliocene turbidites, AAPG Bull. (1) (1977) 137-168.

[52] K.J. Hsu, Studies of ventura field, California: ii, lithology, compaction, and permeability of sands, AAPG Bull. (2) (1977) 169-191.