RESEARCH ARTICLE

Characterization of aerodynamic performance of wind-lens turbine using high-fidelity CFD simulations

  • Islam HASHEM 1 ,
  • Aida A. HAFIZ 2 ,
  • Mohamed H. MOHAMED , 3
Expand
  • 1. Mechanical Power Engineering Department, Faculty of Engineering-Mataria, Helwan University, Cairo 11718, Egypt; State Key Laboratory of Hydroscience and Engineering, Department of Energy and Power Engineering, Tsinghua University, Beijing 100084, China
  • 2. Mechanical Power Engineering Department, Faculty of Engineering-Mataria, Helwan University, Cairo 11718, Egypt
  • 3. Mechanical Power Engineering Department, Faculty of Engineering-Mataria, Helwan University, Cairo 11718, Egypt; Mechanical Engineering Department, College of Engineering and Islamic Architecture, Umm Al-Qura University, Makkah5555, Saudi Arabia

Received date: 14 Mar 2019

Accepted date: 13 Jul 2020

Published date: 15 Aug 2022

Copyright

2020 Higher Education Press

Abstract

Wind-lens turbines (WLTs) exhibit the prospect of a higher output power and more suitability for urban areas in comparison to bare wind turbines. The wind-lens typically comprises a diffuser shroud coupled with a flange appended to the exit periphery of the shroud. Wind-lenses can boost the velocity of the incoming wind through the turbine rotor owing to the creation of a low-pressure zone downstream the flanged diffuser. In this paper, the aerodynamic performance of the wind-lens is computationally assessed using high-fidelity transient CFD simulations for shrouds with different profiles, aiming to assess the effect of change of some design parameters such as length, area ratio and flange height of the diffuser shroud on the power augmentation. The power coefficient (Cp) is calculated by solving the URANS equations with the aid of the SST k–ω model. Furthermore, comparisons with experimental data for validation are accomplished to prove that the proposed methodology could be able to precisely predict the aerodynamic behavior of the wind-lens turbine. The results affirm that wind-lens with cycloidal profile yield an augmentation of about 58% increase in power coefficient compared to bare wind turbine of the same rotor swept-area. It is also emphasized that diffusers (cycloid type) of small length could achieve a twice increase in power coefficient while maintaining large flange heights.

Cite this article

Islam HASHEM , Aida A. HAFIZ , Mohamed H. MOHAMED . Characterization of aerodynamic performance of wind-lens turbine using high-fidelity CFD simulations[J]. Frontiers in Energy, 2022 , 16(4) : 661 -682 . DOI: 10.1007/s11708-020-0713-0

1
Inoue M, Sakurai A, Ohya Y. A simple theory of wind turbine with brimmed diffuser. Turbomachinery, 2002, 30(8): 497–502 (in Japanese)

2
Ohya Y, Karasudani T. A shrouded wind turbine generating high output power with wind-lens technology. Energies, 2010, 3(4): 634–649

DOI

3
Abe K, Nishida M, Sakurai A, Experimental and numerical investigations of flow fields behind a small wind turbine with a flanged diffuser. Journal of Wind Engineering and Industrial Aerodynamics, 2005, 93(12): 951–970

DOI

4
Ohya Y, Karasudani T, Sakurai A, Development of a high-performance wind turbine equipped with a brimmed diffuser shroud. Transactions of the Japan Society for Aeronautical and Space Sciences, 2006, 49(163): 18–24

DOI

5
Abe K, Kihara H, Sakurai A, An experimental study of tip-vortex structures behind a small wind turbine with a flanged diffuser. Wind and Structures, 2006, 9(5): 413–417

DOI

6
Ohya Y, Karasudani T, Sakurai A, Development of a shrouded wind turbine with a flanged diffuser. Journal of Wind Engineering and Industrial Aerodynamics, 2008, 96(5): 524–539

DOI

7
Toshimitsu K, Nishikawa K, Haruki W, PIV measurements of flows around the wind turbines with a flanged-diffuser shroud. Journal of Thermal Science, 2008, 17(4): 375–380

DOI

8
Abe K, Ohya Y. An investigation of flow fields around flanged diffusers using CFD. Journal of Wind Engineering and Industrial Aerodynamics, 2004, 92(3–4): 315–330

DOI

9
Takahashi S, Hata Y, Ohya Y, Behavior of the blade tip vortices of a wind turbine equipped with a brimmed-diffuser shroud. Energies, 2012, 5(12): 5229–5242

DOI

10
Ohya Y, Uchida T, Karasudani T, Numerical studies of flows around a wind turbine equipped with flanged-diffuser shroud by using an actuator-disc model. Wind Engineering, 2012, 36(4): 455–472

DOI

11
Lilley G M, Rainbird W J. A preliminary report on the design and performance of a ducted windmill. Cranfield: The College of Aeronautics, 1956

12
Gilbert B L, Oman R A, Foreman K M. Fluid dynamics of diffuser-augmented wind turbines. Journal of Energy, 1978, 2(6): 368–374

DOI

13
Gilbert B L, Foreman K M. Experiments with a diffuser-augmented model wind turbine. Journal of Energy Resources Technology, 1983, 105(1): 46–53

DOI

14
Igra O. Research and development for shrouded wind turbines. Energy Conversion and Management, 1981, 21(1): 13–48

DOI

15
Phillips D G, Richards P J, Flay R G J. Diffuser development for a diffuser augmented wind turbines using computational fluid dynamics. Technical Report, University of Auckland, 2005

16
Phillips D G, Flay R G J, Nash T A. Aerodynamic analysis and monitoring of the Vortec 7 diffuser-augmented wind turbine. Transactions of the Institution of Professional Engineers of New Zealand: Electrical/Mechanical/Chemical Engineering Section, 1999, 26(1): 13–19

17
Bet F, Grassmann H. Upgrading conventional wind turbines. Renewable Energy, 2003, 28(1): 71–78

DOI

18
Fletcher C A J. Computational analysis of diffuser-augmented wind turbines. Energy Conversion and Management, 1981, 21(3): 175–183

DOI

19
Loeffler A L Jr, Vanderbilt D. Inviscid flow through wide-angle diffuser with actuator disk. AIAA Journal, 1978, 16(10): 1111–1112

DOI

20
Loeffler A L Jr. Flow field analysis and performance of wind turbines employing slotted diffusers. Journal of Solar Energy Engineering, 1981, 103(1): 17–22

DOI

21
Georgalas C G, Koras A D. Calculations of wind-flow through thin annular augmentors of very high aspect ratio. Wind Engineering, 1987, 11(4): 225–233

22
Hansen M, Sørensen N, Flay R G J. Effect of placing a diffuser around a wind turbine. Wind Energy (Chichester, England), 2000, 3(4): 207–213

DOI

23
Phillips D. An Investigation on diffuser augmented wind turbine design. Dissertation for the Doctoral Degree. Auckland: University of Auckland, 2003

24
Watson S J, Infield D G, Barton S J, Modelling of the performance of a building-mounted ducted wind turbine. Journal of Physics: Conference Series, 2007, 75: 012001

DOI

25
Nasution A, Purwanto D W. Optimized curvature interior profile for diffuser augmented wind turbine (DAWT) to increase its energy-conversion performance. In: Proceedings of 2011 IEEE Conference on Clean Energy and Technology (CET), Kuala Lumpur, IEEE. 2011, 315–320

26
Gomis L L. Effect of diffuser augmented micro wind turbines features on device performance. Dissertation for the Master Degree. Wollongong: University of Wollongong, 2011

27
Hjort S, Larsen H. A multi-element diffuser augmented wind turbine. Energies, 2014, 7(5): 3256–3281

DOI

28
Oka N, Furukawa M, Yamada K, Aerodynamic design optimization of wind-lens turbine. In: ASME 2013 Fluids Engineering Division Summer Meeting, 2013

DOI

29
Hu J F, Wang W X. Upgrading a shrouded wind turbine with a self-adaptive flanged diffuser. Energies, 2015, 8(6): 5319–5337

DOI

30
Liu J, Song M, Chen K, An optimization methodology for wind lens profile using computational fluid dynamics simulation. Energy, 2016, 109: 602–611

DOI

31
Khamlaj T A, Rumpfkeil M P. Analysis and optimization of ducted wind turbines. Energy, 2018, 162: 1234–1252

DOI

32
Thé J, Yu H. A critical review on the simulations of wind turbine aerodynamics focusing on hybrid RANS-LES methods. Energy, 2017, 138: 257–289

DOI

33
Menter F R. Two-equation eddy-viscosity turbulence models for engineering applications. AIAA Journal, 1994, 32(8): 1598–1605

DOI

34
Yu H, Thé J. Validation and optimization of SST k--w turbulence model for pollutant dispersion within a building array. Atmospheric Environment, 2016, 145: 225–238

DOI

35
Yu H, Thé J. Simulation of gaseous pollutant dispersion around an isolated building using the k–w SST (shear stress transport) turbulence model. Journal of the Air & Waste Management Association, 2017, 67(5): 517–536

DOI

36
Daróczy L, Janiga G, Petrasch K, Comparative analysis of turbulence models for the aerodynamic simulation of H-Darrieus rotors. Energy, 2015, 90(Part 1): 680–690

DOI

37
Hansen M, Sørensen J, Michelsen J, A global Navier-Stokes rotor prediction model. In: Proceedings of 35th Aerospace Sciences Meeting and Exhibit, Reno, NV, USA. 1997, 0970

38
Sørensen N, Hansen M. Rotor performance predictions using a Navier-Stokes method. In: Proceedings of 1998 ASME Wind Energy Symposium, Reno, NV, USA. 1998, 0025

39
Bak C, Fuglsang P, Sørensen N N, Airfoil Characteristics for Wind Turbines. Risø. Nation Laboratory, Roskilde, 1999

40
Mansour K, Meskinkhoda P. Computational analysis of flow fields around flanged diffusers. Journal of Wind Engineering and Industrial Aerodynamics, 2014, 124: 109–120

DOI

41
Aranake A C, Lakshminarayan V K, Duraisamy K. Computational analysis of shrouded wind turbine configurations using a 3-dimensional RANS solver. Renewable Energy, 2015, 75: 818–832

DOI

42
Harvey N W, Ramsden K. A computational study of a novel turbine rotor partial shroud. Journal of Turbomachinery, 2001, 123(3): 534–543

DOI

43
El-Zahaby A M, Kabeel A E, Elsayed S S, CFD analysis of flow fields for shrouded wind turbine’s diffuser model with different flange angles. Alexandria Engineering Journal, 2017, 56(1): 171–179

DOI

44
Hashem I, Mohamed M H. Aerodynamic performance enhancements of H-rotor Darrieus wind turbine. Energy, 2018, 142: 531–545

DOI

45
Kim B, Kim J, Kikuyama K, 3-D numerical predictions of horizontal axis wind turbine power characteristics of the scaled Delft University T40/500 Model. In: Proceedings of the 5th JSME-KSME Fluids Engineering Conference, Nagoya, Japan. 2002, 17–21

46
Hansen M O L, Johansen J. Tip studies using CFD and comparison with tip loss models. Wind Energy (Chichester, England), 2004, 7(4): 343–356

DOI

47
Ferrer E, Munduate X. Wind turbine blade tip comparison using CFD. Journal of Physics: Conference Series, 2007, 75: 012005

DOI

48
Laursen P, Enevoldsen P, Hjort S. 3D CFD quantification of the performance of a multi-megawatt wind. Journal of Physics: Conference Series, 2007, 75: 012007

DOI

49
Amano R S, Malloy R J. CFD analysis on aerodynamic design optimization of wind turbine rotor blades. World Academy of Science, Engineering and Technology, 2009, 60: 71–75

50
Hashem I, Mohamed M H, Hafiz A A. Aero-acoustics noise assessment for wind-lens turbine. Energy, 2017, 118: 345–368

DOI

51
Hashem I, Mohamed M H, Hafiz A A. Numerical prediction of aero-acoustics emitted from shrouded wind turbines. In: Proceedings of ICFD12: 12th International Conference of Fluid Dynamics, Le Méridien Pyramids Hotel, Egypt. 2016, 5008

52
Hashem I, Mohamed M H, Hafiz A A. Numerical investigation of small-scale shrouded wind turbine with a brimmed diffuser. In: Proceedings of ICFD12: 12th International Conference of Fluid Dynamics, Le Méridien Pyramids Hotel, Egypt. 2016, 5003

53
Dessoky A, Bangga G, Lutz T, Aerodynamic and aeroacoustic performance assessment of H-rotor Darrieus VAWT equipped with wind-lens technology. Energy, 2019, 175: 76–97

DOI

54
Matsumiya H, Kogaki T, Takahashi N, Development and experimental verification of the new MEL airfoil series for wind turbines. In: Proceedings of Japan Wind Energy Symposium, 2000, 22: 92–95 (in Japanese)

55
Khamlaj T A, Rumpfkeil M. Optimization study of shrouded horizontal axis wind turbine. In: Proceedings of the 2018 Wind Energy Symposium, Kissimmee, Florida. 2018, 0996

56
Hashem I, Abdel Hameed H S, Mohamed M H. An axial turbine in an innovative oscillating water column (OWC) device for sea-wave energy conversion. Ocean Engineering, 2018, 164: 536–562

DOI

57
Song Y, Perot J B. CFD simulation of the NREL phase VI rotor. Wind Engineering, 2015, 39(3): 299–309

DOI

58
Kody S, Alpman E, Yilmaz B. Computational studies of horizontal axis wind turbines using advanced turbulence models. Fen Bilimleri Dergisi, 2014, 26(2): 36–46

DOI

59
El-Baz A R, Youssef K, Mohamed M H. Innovative improvement of a drag wind turbine performance. Renewable Energy, 2016, 86: 89–98

DOI

Outlines

/