1. Hangzhou International Innovation Institute, Beihang University, Hangzhou 311115, China
2. School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China
3. Center for Medical Metrology, National Institute of Metrology, Beijing 100029, China
4. National Key Laboratory of Science and Technology on Power Beam Processes, AVIC Aeronautical Manufacturing Technology Research Institute, Beijing 100024, China
5. Ningbo Institute of Technology, Beihang University, Ningbo 315832, China
wangliang@buaa.edu.cn (Wang L.),
yuansm@buaa.edu.cn (Yuan S.).
Show less
History+
Received
Accepted
Published Online
2026-07-27
2026-10-12
2026-11-18
PDF
(34373KB)
i
This article has been updated.A Correction to this article was published on .
Silicon carbide ceramic matrix composites (SiC-CMCs) serve as pivotal structural materials for aerospace, energy and transportation industries due to their outstanding high-temperature mechanical performance, low density and high damage resistance. Nevertheless, their extreme hardness, pronounced anisotropy and heterogeneity lead to severe limitations in conventional machining, such as excessive tool wear, low efficiency, and inevitable defects including delamination and fiber breakage. Benefiting from non-contact processing, ultrahigh energy density and force-free material removal, laser processing offers a promising alternative to overcome the above difficulties. This paper systematically reviews the state-of-the-art advances in laser ablation of SiC-CMCs. This review elaborates the evolution of the ablation mechanisms, anisotropic heat transfer, oxidation and phase transformation behaviors, as well as numerical simulation progress. Key ablation characteristics are analyzed in terms of material removal rate, ablation threshold, morphological defect evolution, physicochemical reactions and microstructural damage. Classified by laser pulse width, various laser machining strategies and innovative hybrid processes are reviewed regarding their applications, optimization and limitations. This review organizes the available evidence on laser ablation of SiC-CMCs, identifies research boundaries and technical bottlenecks, and outlines future research directions to support fundamental investigation and engineering-oriented process development.
High-performance machining is essential for translating the structural potential of ceramic matrix composites (CMCs) into reliable engineering components. Silicon carbide ceramic matrix composites (SiC-CMCs) are particularly relevant to lightweight components operating under demanding thermal and mechanical conditions. Research across ceramic and composite systems underscores the relationship between material architecture, fabrication, and machining-induced surface integrity [1–5]. These broader developments provide context, but SiC-CMCs require a material-specific understanding of processing and damage. Reviews of laser machining and electrical discharge machining of ceramics provide relevant process-level background [6–8]. The present review addresses the additional complexity introduced by constituent interactions during SiC-CMC laser ablation.
The central difficulty is that material removal is governed by local properties and damage mechanisms rather than by nominal composition alone [9–12]. Studies of CMC machining and laser ablation across different ceramic systems further demonstrate the importance of distinguishing material-specific responses [13–15]. Within this broader family, SiC-CMCs bring together questions of machinability, anisotropic damage, and suitability for demanding thermal applications [16–18]. This review focuses on carbon fiber-reinforced SiC (C/SiC) and SiC fiber-reinforced SiC (SiC/SiC) composites. Mechanical damage studies highlight why architecture and loading conditions must be considered when interpreting their behavior [19,20]. Research on C/SiC fabrication and machining links processing choices with defect formation and machinability [21–23]. Complementary modeling and characterization of CMC damage, including SiC/SiC systems, emphasize the need to assess both surface and subsurface integrity [24–27]. These considerations motivate a material-resolved treatment of laser ablation.
Fabrication is relevant to laser-machining analysis because it determines the initial material state encountered by the laser [28,29]. Representative densification routes include polymer infiltration and pyrolysis (PIP) [30–32], chemical vapor infiltration (CVI) [33–35], and melt infiltration (MI), including liquid silicon infiltration (LSI) [36–38]. Hybrid routes, such as CVI+PIP [39–41], CVI+MI [37,42], and PIP+LSI [43], have also been developed to balance densification efficiency and material performance. For the present review, the importance of these routes lies not in their processing details but in the resulting matrix structure, porosity, interphase condition, and residual phases. These material characteristics govern local optical absorption, heat transport, interfacial stress development, and constituent-specific removal. Identifying the fabrication-dependent material state is therefore essential for distinguishing inherent material effects from changes caused by laser parameters.
Although these fabrication routes enable near-net-shape production, the subsequent manufacture of precision features, such as cooling holes, grooves, sealing surfaces, and assembly interfaces, still requires controlled material removal. The high hardness, brittleness, anisotropy, and multiscale heterogeneity of SiC-CMCs make such operations particularly challenging [13,16,44,45]. Conventional milling [46,47], grinding [48,49], and drilling [50,51] can be implemented using established manufacturing platforms and are suitable for accessible surfaces and relatively simple features. However, the large and spatially varying cutting loads generated during tool–material contact can cause matrix cracking, fiber fracture, pull-out, interfacial debonding, and edge chipping. Interfacial fracture behavior is especially important because separation may occur preferentially between the fiber, interphase, and matrix [52]. Moreover, fiber orientation and local structural variation lead to fluctuations in cutting force and removal mode, thereby reducing the consistency of the machined geometry and surface integrity [53–55]. Tool wear and the associated deterioration in dimensional accuracy further constrain machining efficiency. Consequently, dimensional accuracy alone is insufficient for evaluating machining quality; surface and subsurface damage must also be considered in relation to the functional requirements of the component.
These limitations have stimulated the development of multiple complementary machining routes, and no single method can be regarded as universally superior for all SiC-CMC components [45,46]. Abrasive waterjet machining can process relatively thick sections without producing a conventional heat-affected zone (HAZ), but jet divergence, kerf taper, abrasive erosion, and limited control of local fiber damage can restrict its use for high-precision features [56,57]. Electrical discharge machining (EDM) avoids macroscopic cutting forces and can generate complex or deep geometries; nevertheless, its applicability depends on sufficient electrical conductivity, while electrode wear, relatively low removal efficiency, and thermally altered or recast surfaces may require additional treatment [58,59]. Ultrasonic vibration-assisted machining can reduce cutting forces and improve chip or debris removal, but it remains a contact-based process and does not completely eliminate tool wear or mechanically induced subsurface damage [60–64]. By contrast, laser machining enables non-contact and spatially localized energy delivery, provides high geometrical flexibility, and avoids direct tool wear, making it promising for microholes, grooves, and other complex features [65–67]. Its equipment and energy costs may be comparatively high, but these disadvantages can be partly offset by reduced tool consumption, high automation potential, and limited mechanical post-processing. Nevertheless, a general quantitative ranking of machining efficiency, surface quality, or cost-effectiveness remains difficult because published studies differ substantially in material architecture, feature geometry, workpiece thickness, productivity definition, production scale, consumable use, and post-processing requirements.
Against this process landscape, laser ablation warrants focused examination because its principal advantages are accompanied by damage mechanisms that differ fundamentally from those of contact machining. Water- and fluid-assisted laser processes can modify heat transfer, debris evacuation, plasma shielding, and chemical reactions within the interaction zone [68–71], whereas laser–mechanical hybrid approaches seek to combine localized laser-induced material modification with efficient mechanical removal [72–75]. However, eliminating direct mechanical contact does not guarantee damage-free machining. Depending on the wavelength, pulse duration, energy input, scanning strategy, material architecture, and surrounding medium, localized laser energy deposition can generate oxidation, recast layers, microcracks, residual stress, and HAZ. Short-pulse lasers and auxiliary media may mitigate some of these effects, but their benefits remain dependent on the specific operating conditions and evaluation criteria. Differences in the ablation responses of fibers, matrices, and interphases can also produce nonuniform removal and complicate geometrical control. Moreover, an apparently clean surface does not necessarily demonstrate the absence of subsurface or interfacial damage. The broader machining literature therefore highlights a persistent trade-off between removal capability and surface integrity [10,45], while reviews of CMC processing and high-temperature applications emphasize that process selection must account for both the initial material state and the intended service requirements [75,76]. Accordingly, rather than attempting to establish a universal ranking among fundamentally different machining technologies, the present review focuses on how material structure, laser irradiation, and processing environment jointly govern the efficiency–damage balance in laser ablation of SiC-CMCs.
Previous reviews provide valuable foundations for addressing these questions in SiC-CMC machining. They cover fabrication and machining across ceramic composite systems [77,78], compare conventional and nonconventional machining approaches [44,45,79], and examine machining-induced damage and surface integrity [13,16]. A dedicated review also discusses laser and SiC-CMCs interactions, laser and hybrid processes, and their effects on material properties [80]. Building on these contributions, a focused synthesis is needed to connect ablation mechanisms, observable material responses, and process selection for SiC-CMCs. A central difficulty is distinguishing broadly supported relationships from findings restricted to particular materials or operating conditions. Mechanistic explanations therefore need to be linked to measured removal and damage, with attention to the evidence supporting each interpretation. Comparisons must distinguish changes caused by laser parameters from differences in fiber architecture, interphase, and initial material state. Without these distinctions, improvements demonstrated in one configuration may be overgeneralized to other material systems or processing regimes.
Table 1 compares representative existing reviews with the present work. Previous reviews have established substantial coverage of CMC machining, surface integrity, laser interactions, and hybrid processes [13,45,77,79,80]. The contribution of this review is therefore a complementary critical synthesis, rather than the first discussion of these topics. Specifically, it connects constituent-dependent energy deposition and ablation mechanisms with measured removal, chemical modification, and microstructural damage; distinguishes numerical verification, calibration, and independent validation; and consolidates laser-processing conditions and outcomes using explicit removal-rate definitions and comparability limits. The service-oriented discussion further separates demonstrated damage–strength associations from unresolved durability relationships. Together, these elements provide a mechanism–behavior–process framework for interpreting efficient, low-damage machining without treating C/SiC and SiC/SiC, or unmatched processing conditions, as interchangeable.
The present review is therefore organized around three related questions. First, how do constituent properties, fiber orientation, and processing conditions influence energy absorption, heat transfer, and material removal? Second, how are these interactions reflected in ablation thresholds, removal rates, morphology, chemical changes, and microstructural damage? Third, what do these relationships imply for selecting pulse-duration regimes and auxiliary processing strategies? Addressing these questions requires separating experimentally observed behavior from mechanistic interpretation and identifying where numerical models provide supporting evidence. It also requires recognizing when differences in specimens, laser settings, or reported metrics prevent direct cross-study comparisons. The aim is to clarify both useful processing trends and the boundaries of their applicability.
The review follows a mechanism, behavior and process sequence (Fig. 1). Section 2 examines laser-material interaction mechanisms, anisotropic heat transfer, and numerical modeling approaches. Section 3 discusses removal rates and ablation thresholds, morphological evolution, physicochemical reactions, and microstructural damage. Section 4 evaluates laser processing from continuous-wave (CW) to femtosecond regimes, together with hybrid approaches and their limitations. Section 5 brings together supported findings, unresolved questions, and future research directions. This organization links physical understanding with process-level decisions while retaining the distinctions needed for a critical review. Its intended contribution is an evidence-based account of efficient, low-damage laser ablation of SiC-CMCs.
Literature search, selection, and scope. The literature was searched in the Web of Science Core Collection, Scopus, Engineering Village, and CNKI from database inception through June 18, 2026. Material terms (“ceramic matrix composite*”, “SiC/SiC”, “SiCf/SiC”, “C/SiC”, “Cf/SiC”, and “carbon-fiber-reinforced silicon carbide”) were combined with process terms (“laser ablation”, “laser machin*”, “laser drill*”, “laser groov*”, “laser polish*”, “waterjet-guided laser”, “water-assisted laser”, “nanosecond laser”, “picosecond laser”, and “femtosecond laser”). Reference lists and forward citations of key studies were also screened. Studies were included if they investigated SiC-based CMCs and addressed laser-material interactions, material removal, damage, oxidation, modeling, monitoring, or process optimization. Duplicate records, abstract-only reports lacking sufficient technical information, nontechnical publications, and irrelevant studies were excluded. Foundational studies and investigations of adjacent materials or processes were retained only for mechanistic or methodological context and treated as indirect evidence. The review focuses primarily on C/SiC (Cf/SiC) and SiC/SiC (SiCf/SiC), collectively termed SiC-CMCs because of their common SiC-based laser-interaction framework. This grouping does not imply interchangeable material responses. Accordingly, case-specific findings identify the material system and, where reported, its architecture, interphase, porosity or density, and fabrication route; broader conclusions are drawn only when supported across systems. Modified, coated, or neighboring ceramic systems are explicitly qualified. The bibliography spans 1973–2026, with direct evidence on laser processing of SiC-CMCs concentrated mainly in 2013–2026.
2 Laser Ablation Mechanism of SiC-CMCs
The interaction between a laser and SiC-CMCs is an extremely complex, transient process characterized by extreme nonequilibrium conditions and coupled multi-physics phenomena, occurring within ultrashort temporal scales (from femtoseconds to milliseconds) and minute spatial scales (from nanometers to millimeters). Its fundamental nature lies in the transfer of photon energy to the electronic and lattice energy of the material, subsequently triggering a cascade of phase transformations, chemical reactions, mechanical responses, and structural evolution. A profound understanding of the laser-material interaction mechanism forms the theoretical cornerstone for predicting machining outcomes, optimizing process parameters, and controlling machining-induced damage. The dominant mechanism is governed by the interplay between laser parameters, primarily pulse duration, wavelength, and energy density, and the material’s intrinsic optical properties, thermophysical characteristics, chemical reactivity, and microstructure.
2.1 Photothermal and photochemical effects
The initial stage of laser-matter interaction involves the absorption of photon energy by electrons within the material. The subsequent material removal mechanism is fundamentally determined by the energy relaxation pathway: whether the absorbed energy is primarily converted into lattice thermal energy via electron−phonon collisions, or directly leads to chemical bond breaking through photoionization or Coulomb explosion. The selection of this pathway is fundamentally governed by the relative magnitudes of the laser pulse duration and the material’s characteristic electron−phonon coupling relaxation time, thereby defining the two dominant mechanistic regimes: the photothermal effect and the photochemical effect. Accordingly, the photothermal/photochemical division used below should be understood as a description of the dominant energy-transfer pathway rather than a strict binary classification. In addition to pulse duration relative to the electron–phonon coupling time, wavelength, fluence, repetition rate, pulse overlap, and the constituent-specific optical and thermophysical properties collectively govern the relative contributions of thermal diffusion, nonlinear absorption, plasma formation, and mechanically driven material ejection.
When the laser pulse duration is significantly longer than the material’s electron−phonon coupling time (typically on the order of picoseconds), as in the interaction of CW, millisecond, and nanosecond lasers with SiC-CMCs, the energy deposition and dissipation processes strictly adhere to classical thermodynamic laws. The photon energy absorbed by the material is first deposited within the electron system. Subsequently, through frequent electron−phonon scattering, this energy is rapidly converted into lattice thermal energy on a picosecond timescale. This process dictates that the evolution of the internal temperature field follows Fourier’s law of heat conduction. Heat transfers from the surface inwards via thermal diffusion, subjecting the material to rapid heating, melting, vaporization, and even sublimation. Concurrently, the high-temperature environment activates thermally-driven chemical reactions within the material, such as thermal decomposition. These thermally-activated chemical processes are tightly coupled with the physical phase transitions, collectively governing the material removal behavior (Fig. 2A). Since the entire ablation process is driven by the accumulation and transfer of thermal energy, material removal exhibits distinct thermal erosion characteristics [71,85–87]. From a macro-processing quality perspective, laser ablation dominated by the photothermal effect inevitably introduces a series of thermal damage issues. Due to the long interaction time and severe heat accumulation, the processed region is often accompanied by a pronounced HAZ and the formation of a recast layer. Consequently, this type of processing is commonly referred to as thermal processing [88–90].
In the photothermal effect-dominated ablation process, material removal is a dynamic outcome resulting from the competition of multiple physicochemical mechanisms. When the laser power density is low and the surface temperature does not reach the sublimation threshold, thermally activated oxidation reactions dominate the process [91]. However, as the laser energy density increases, the surface temperature rises sharply and exceeds the sublimation threshold. Under these conditions, both the SiC matrix and carbon fibers undergo intense decomposition and direct sublimation, leading to a significant acceleration of the MRR (Fig. 2B). Furthermore, under sustained irradiation with high-energy lasers, a molten liquid layer (e.g., elemental silicon or silicate melt) may even form locally. Driven by surface tension or scoured by gas flow shear forces, this liquid material migrates, splashes, and re-solidifies, forming typical recast layers or reticulated micro-morphologies on the bottom or sidewalls of the ablation crater [71,92]. Macroscopically, this manifests as a rapid increase in ablation depth and the emergence of a temperature leap phenomenon (Fig. 2C) [93,94].
When the laser pulse duration becomes comparable to or shorter than the characteristic electron–phonon energy-relaxation time of the constituent materials, as in picosecond and femtosecond irradiation, nonequilibrium electronic excitation becomes increasingly important [95]. However, this change should not be regarded as a sharp transition from purely photothermal ablation to purely photochemical or non-thermal ablation. At sufficiently high peak intensities, nonlinear absorption processes, including multiphoton absorption and tunneling ionization, may become important, although their contributions depend on the wavelength, fluence, and constituent-specific optical properties. The resulting rapid electronic excitation and ionization can generate a dense plasma [96] (Fig. 2D). For femtosecond pulses, energy deposition can largely precede electron–phonon equilibration, whereas for picosecond pulses, appreciable energy transfer to the lattice may already occur during the pulse. The two regimes therefore exhibit different degrees of electron–lattice nonequilibrium [97]. Rapid ionization and electron emission may leave a positively charged surface region, allowing electrostatic repulsion to drive Coulomb explosion and ion ejection. In contrast, phase explosion is a thermally driven pathway: where a transient molten phase forms, sufficient lattice heating can bring it into a metastable superheated state, followed by explosive liquid–vapor separation (Fig. 2E) [95]. Plasma pressure, vapor recoil, and shock waves may additionally contribute to mechanical material ejection. Although ultrashort energy deposition restricts thermal diffusion during an individual pulse, subsequent electron–lattice relaxation and heat accumulation at high repetition rates or pulse overlaps may still produce melting, recast layers, and a finite HAZ [97]. Direct electronic excitation and bond-breaking pathways may contribute substantially under suitable ultrafast irradiation conditions (Fig. 2F) [95,96]. Therefore, the relative contributions of thermal diffusion, nonlinear absorption, plasma formation, and mechanical ejection are governed collectively by pulse duration, wavelength, fluence, repetition rate, pulse overlap, and the optical and thermophysical properties of the fiber, matrix, and interphase. Picosecond ablation should consequently be regarded as a transitional, parameter-dependent regime in which thermal and non-thermal pathways may coexist.
2.2 Material anisotropy and heat transfer mechanism
C/SiC and SiC/SiC are discussed within a common mechanistic framework, but their laser-ablation responses should not be regarded as interchangeable. Differences in thermal transport, oxidation behavior, and interphase characteristics must be interpreted alongside the irradiation conditions and composite architecture. Even within SiC/SiC, variations in density can alter laser-machining morphology. Accordingly, the findings reviewed here should be interpreted within their reported material and processing conditions; differences between studies should not be attributed to reinforcement type alone.
The outstanding performance of SiC-CMCs originates from the continuous fiber architecture of their reinforcement phase. However, this very structure introduces a pronounced anisotropy that permeates both the material’s intrinsic properties and its response to machining. In the context of laser processing, an extreme transient thermal process, the directional dependence of the material’s thermal and mechanical properties is not a secondary factor, but rather the decisive internal cause governing energy deposition, temperature distribution, phase transformation sequences, and ultimately, the failure mode. It constitutes the fundamental source of spatial non-uniformity in machining outcomes and the complexity in process predictability.
Thermal conduction anisotropy is the physical root cause of non-uniform temperature fields and energy deposition. Both high-conductivity carbon fibers and silicon carbide fibers exhibit significantly higher thermal conductivity along their axial direction compared to their radial direction, typically also far exceeding the conductivity of the matrix [99]. This order-of-magnitude difference drastically modulates heat diffusion during laser irradiation: efficient thermal channels form along the fiber axis, rapidly conducting energy away from the irradiation center; whereas in directions perpendicular to the fibers and within matrix-rich zones between fiber bundles, heat diffusion is hindered, leading to energy accumulation [87,99]. The detailed finite element simulations by Zhai et al. [99] clearly demonstrate that the peak temperature generated by laser irradiation on a fiber bundle can differ by over 1000 K from that on an adjacent matrix region (Fig. 3A). This non-uniform energy dissipation, determined by the meso-structure and strongly dependent on location and orientation, is the starting point for all subsequent differentiated responses.
The thermal conduction anisotropy is further evidenced in simulations of picosecond laser ablation. After laser energy deposition, heat preferentially and rapidly conducts and diffuses along the fiber axial direction, while conduction along the radial direction and through the matrix is considerably slower [89,96,100]. Consequently, the relative orientation between the laser scanning path and the fiber axis critically influences the thermal field. When the laser scans perpendicular to the fiber axis, heat becomes trapped within the low-conductivity matrix and the fiber radial direction, generating localized high temperatures and more intense ablation. In contrast, when scanning parallel to the fiber axis, heat is swiftly conducted away along this axial high-speed channel, resulting in shallower ablation and a smaller HAZ (Fig. 3B). Here, “parallel” and “perpendicular” refer to the angle between the laser scanning path and the dominant in-plane fiber-bundle direction exposed at the processed surface. Preferential heat conduction along the fiber axis does not impose a universal groove geometry. Moreover, groove depth and width are separate geometric measures; removal efficiency should be evaluated from the removed cross-sectional area, volume, or mass per unit time, and greater depth alone does not necessarily indicate a higher MRR.
The anisotropy in material removal behavior and damage modes is a direct consequence of thermal conduction anisotropy. Fibers with different orientations exhibit markedly distinct responses to laser energy and failure mechanisms. In their study on millisecond laser trepanning, Liu et al. [101] meticulously documented the evolution of differently oriented fibers. This inherent anisotropic removal behavior is the direct cause of uneven surface roughness, poor hole circularity, and inconsistent groove sidewall taper angles in the machined features [102]. Mitigating this anisotropy therefore requires intervention through both beam shaping, such as rotating multi-beam configurations [103], and scanning-path optimization [100].
2.3 Progress in multiscale numerical modeling
Laser interaction with SiC-CMCs involves rapid, localized energy deposition and coupled physical processes that are difficult to observe directly. Multiscale modeling therefore supports mechanism interpretation, morphology prediction, and process optimization [104]. Fig. 4 summarizes modeling approaches across characteristic length scales [105]. However, model resolution and physical complexity do not, by themselves, establish predictive accuracy. The relevant questions are which observables have been validated, under what conditions, and with what uncertainty.
Continuum approaches, including the finite element method (FEM) and computational fluid dynamics (CFD), describe heat transfer and, where included, fluid motion and material removal. Representative applications address thermal responses [106,107] and waterjet-assisted laser processing [108,109]. Homogenized descriptions reduce computational cost but obscure constituent-dependent transport and local fiber–matrix interactions. Constituent-resolved FEM can address some of these limitations; FEM is therefore not restricted to the macroscale. Phase-field and discrete-element approaches provide additional frameworks for evolving interfaces and discontinuities in broader multiscale modeling [110]. Their inclusion indicates methodological potential, rather than established validation for SiC-based CMC laser ablation.
At smaller scales, molecular dynamics (MD) and related atomistic approaches investigate structural changes and removal mechanisms [111,112]. Applications cover single-crystal materials [113–115], metals and alloys [116–118], inorganic nonmetallic materials [119–121], and composite or joined systems [122,123]. These studies span different processes and material systems, so their validation cannot be transferred directly to CMC laser ablation. Atomistic predictions depend on interatomic potentials, energy-deposition assumptions, and accessible time and length scales. Validation should therefore address the relevant mechanism and material state, rather than rely solely on agreement with a macroscopic removal depth.
The required physics also depends on the irradiation regime. For CW and long-pulse irradiation, heat-transfer models relate temperature evolution to ablation and surface modification [91] (Fig. 5A). Models incorporating evolving properties and attenuation by ablation products have investigated the temperature-jump behavior of C/SiC [87,93,94] (Fig. 5B). Modified C/SiC–Ti3SiC2 composites have also been examined using multiscale models [86,92]. However, fitted effective properties or removal criteria may be specific to the tested composition, environment, and exposure range. For nanosecond processing, constituent-resolved modeling identifies fiber-oriented heat-transfer pathways and spatially nonuniform ablation [99] (Fig. 5C). Such results support the importance of anisotropy, but do not establish a universal sensitivity ranking for all composite architectures.
For ultrashort pulses, a single-temperature description can be inadequate during energy nonequilibrium, while Fourier heat conduction remains useful after equilibration. A transient multiphase model with a level-set method has been compared with picosecond-drilled hole dimensions, taper, and profiles [97]. For femtosecond processing, a dual-timescale model couples the two-temperature model (TTM) with subsequent heat diffusion and accounts for dynamic defocusing [67]. Agreement with final geometry supports these specific predictions, but does not independently validate every simulated temperature, pressure, or damage field.
Hybrid processes introduce additional optical and hydrodynamic dependencies [108,109] (Fig. 5D). Cheng et al. [109] reproduced the increasing removal trend with pulse energy, but their analysis also identified limitations in extrapolating initial-pulse removal to sustained machining. Evolving cavity geometry, restricted drainage, and jet disruption reduce the applicability of such extrapolation. Their model neglected molten-pool flow, so it should not be described as resolving the complete removal hydrodynamics. High-speed observations of splashing further demonstrate feedback between jet disturbance and laser transmission. Neural-network-assisted optimization offers another route to process prediction, but agreement between computational models should not be equated with independent experimental validation [128,129].
Published validation results should be interpreted according to their measured quantities and testing conditions. Wang et al. [93] reported an ablation-depth deviation of ~4.45% after 20 s of irradiation. Gao et al. [67] reported an average error below 10% for maximum ablation depth across different powers, scan numbers, and scanning speeds. These results demonstrate case-specific predictive capability, rather than a general error range for CMC ablation models. Maximum depth, mean depth, and removed volume are different observables and must not be treated interchangeably. Similarly, the hole-shape comparisons in Ref. [97] do not alone establish the accuracy of transient fields or recast-layer predictions.
Several mechanisms can explain discrepancies between simulations and experiments. First, fixed absorptivity or beam geometry may misrepresent deposited energy when surface conditions, shielding, or focal position evolve [67,97]. Second, homogenized properties and idealized geometries can suppress local variations associated with fiber orientation, interfaces, and pores [91,99]. Such simplifications may reproduce overall depth while missing asymmetric profiles or localized damage. Third, simplified removal thresholds cannot automatically distinguish decomposition, oxidation, ejection, and redeposition. Consequently, agreement in removed geometry does not necessarily demonstrate an accurate description of surface chemistry or subsurface integrity [91]. Finally, idealized cooling and jet boundaries can miss geometry-dependent drainage and optical–hydrodynamic feedback during prolonged waterjet-guided processing [109,128].
A stronger assessment should distinguish numerical verification, parameter calibration, and experimental validation. Mesh and time-step convergence, together with appropriate conservation checks, assess numerical reliability. Calibration estimates uncertain inputs from experimental observations; comparison with those same observations does not establish independent predictive performance. Validation should use conditions excluded from calibration, such as additional powers, scanning speeds, or fiber orientations. Where possible, it should combine depth or removed volume with lateral geometry, temperature measurements, and independently characterized damage. Experimental resolution, repeatability, and diagnostic assumptions should accompany these comparisons. In particular, a temperature-threshold contour should not automatically be equated with an experimentally identified heat-affected or chemically altered region. Transfer to another composite architecture or processing environment requires additional validation.
Parameter sensitivity should likewise be distinguished from simply varying controllable processing parameters. The critical issue is how uncertainty in model inputs propagates into predicted observables. For thermal models, candidate inputs include absorptivity, delivered energy, beam radius, temperature-dependent conductivity, and heat capacity. Their effects should be examined against depth, width, and thermal-field predictions. Constituent-resolved models additionally require assessment of directional conductivity, interface thermal resistance, and geometric variability. Where relevant, removal thresholds, transformation enthalpies, and reaction-rate parameters should be examined because they determine how deposited energy produces material loss. For TTM-based descriptions, sensitivity to the adopted energy-coupling and transport parameters should be assessed within the model’s material-specific validity range. Waterjet-guided models additionally require assessment of optical transmission, cooling boundaries, and jet conditions. These are candidate sensitivity variables, and their relative importance cannot be inferred solely from the model category.
Sensitivity studies should use measurement-based or otherwise justified parameter ranges and report effects on each validation target. Local perturbations can identify influential inputs near a selected operating point, whereas global approaches can examine nonlinear interactions across broader uncertainty ranges. Rankings should be reported separately for different outputs and irradiation regimes, with numerical discretization errors assessed independently. Multiple observables are particularly important when uncertain inputs can compensate for one another, allowing different parameter sets to reproduce similar depths. Accordingly, future progress requires independently validated predictions and transparent uncertainty reporting, alongside a realistic representation of the mesostructure and stronger multi-physics coupling.
3 Laser Ablation Behavior of SiC-CMCs
The interaction between a laser and SiC-CMCs triggers a series of complex physical and chemical responses, ranging from transient to quasi-static and from microscopic to macroscopic scales, collectively termed laser ablation behavior. A profound understanding of these behavioral patterns serves as the crucial link connecting the underlying interaction mechanisms with the optimization of processing parameters. It is the key to predicting machining outcomes, controlling processing quality, and ultimately achieving performance-oriented manufacturing of components. This section systematically analyzes the dynamic response of the material under laser irradiation, covering a spectrum from macroscopic material removal efficiency and energy thresholds, to mesoscopic surface morphology evolution and defect generation, down to molecular-scale compositional and bonding state alterations, and finally correlating these to the microstructural evolution that determines component service performance.
3.1 Material removal rate and ablation threshold
MRR and ablation threshold are the two most fundamental macroscopic quantitative metrics for characterizing the feasibility, efficiency, and energy utilization of laser machining. Together, they delineate the fundamental relationship between laser energy input and material mass/volume output, serving as the primary basis for process parameter optimization.
3.1.1 Material removal rate
Material removal rate is used in this review as an umbrella term for time-normalized measures of material removal. Depending on the measurement basis, MRR can be expressed as the linear removal rate (LRR, Δl/Δt; μm·s−1 or mm·min−1), volumetric removal rate (VRR, ΔV/Δt; mm3·s−1 or mm3·min−1), or mass removal rate (MaRR, Δm/Δt; mg·s−1 or g·min−1). Hereafter, the unqualified term MRR refers only to the general concept of material removal rate, whereas quantitative results are identified specifically as LRR, VRR, or MaRR according to their definitions and units. By contrast, groove depth (D) and groove width (W), expressed in units of length, are geometric outcomes rather than time-normalized removal rates. Similarly, removed cross-sectional area, ablation depth per pulse, and processing time are retained as separate descriptors unless sufficient information is available to determine a corresponding LRR, VRR, or MaRR. For anisotropic and heterogeneous SiC-CMCs, these removal metrics are jointly governed by laser parameters, material architecture, and the processing environment.
The dominant influence of laser parameters exhibits marked nonlinear characteristics. Under otherwise comparable conditions, increasing the laser average power or single-pulse energy generally increases the measured removal extent and may consequently increase the corresponding LRR, VRR, or MaRR, depending on the quantity evaluated in the original study. For instance, nanosecond laser grooving experiments showed that both groove depth and width increased significantly with laser power [89], as shown in Figs. 6A and 6B1. These quantities characterize changes in groove geometry under the specified processing conditions but are not themselves time-normalized removal rates. However, this growth exhibits a saturation region or even an inflection point. When the energy is excessively high, the generated dense plasma plume exerts a strong shielding effect on subsequent laser pulses, absorbing and scattering the incident laser energy, which consequently reduces energy utilization and slows the increase in the effective MRR [106,130]. The influence of scanning speed is opposite: increasing the scanning speed reduces the laser interaction time and effective pulse number per unit area. In Ref. [67], this effect was reflected primarily by a decrease in groove depth, as shown in Figs. 6B2 and 6B3; the reported groove depth should not be interpreted as a directly measured MRR. The effect of pulse repetition frequency has an optimal value. For ultrafast lasers, a frequency too low fails to utilize thermal accumulation effectively, while one too high may prevent timely heat dissipation, leading to excessive thermal damage rather than efficient removal. Zhang et al. [131] found 200 kHz to be a preferable frequency in picosecond laser machining (as shown in Fig. 6C). Spot overlap ratio is also critical. High overlap ensures continuous coverage of the machined area, but excessive overlap can lead to energy waste and aggravated heat accumulation [95,132].
The profound influence of material anisotropy and microstructure is central to distinguishing composite material machining from that of homogeneous materials. The heat conduction capacity along the fiber axis is far superior to that in the radial direction and the matrix, leading to a strong directional dependence of groove geometry and material removal behavior (as shown in Figs. 6A, 6D1 and 6D2). When the laser scanning direction is parallel to the fiber axis, heat is rapidly conducted away, reducing the energy available for local ablation. Because groove depth and width may vary independently with scanning direction, neither quantity alone represents the MRR. A rigorous comparison of orientation-dependent MRR therefore requires the same time-normalized metric under matched processing conditions, such as LRR, VRR, or MaRR. When only groove geometry is available, the removed cross-sectional area may provide a more complete geometric descriptor than either depth or width alone, but it should still be distinguished from a time-normalized removal rate [89,96,100]. Material density and porosity also significantly alter the energy coupling and transfer processes. Research by Wang et al. [133] found that in nanosecond laser machining, high-density SiC/SiC samples, due to their denser structure and superior thermal conductivity, exhibited more regular ablation morphology and less apparent thermal damage under identical laser parameters, although the mode of energy consumption within the material differed. Furthermore, the properties of the fiber-matrix interface and the distribution of pores influence the generation and release of thermal stress, thereby indirectly affecting material fragmentation and spallation removal behavior.
The regulatory role of the environmental medium and auxiliary processes offers the possibility of actively enhancing MRR [130]. Waterjet-guided laser machining is a typical case. The coaxial water jet not only cools the machining zone and suppresses oxidation, but its high-speed scouring action effectively and promptly removes molten material and debris, preventing secondary laser shielding and redeposition, thereby significantly improving the effective MRR. Research by Bao et al. [134] showed that drilling efficiency was significantly improved after optimizing water jet parameters. The choice of assist gas is also strategic. Cao et al. [135] compared the behavior of nanosecond laser ablation of SiC/SiC under different assist gases. They found that oxygen (O2) could enhance the apparent ablation rate via vigorous oxidation reactions but introduced a severe oxide layer. Inert gases like nitrogen (N2) and helium (He), while not promoting removal through chemical reactions, helped maintain a stable removal process by expelling molten material and purging the machining zone. Chen et al. [136] also verified the significant influence of gas type in quasi-continuous laser drilling.
3.1.2 Ablation threshold
The ablation threshold is operationally defined as the minimum incident laser fluence required to produce material removal detectable using a specified experimental criterion. For heterogeneous SiC-CMCs, however, it should not be regarded as a single intrinsic material constant. A constituent-level threshold refers to the removal onset of an individual constituent, such as a carbon or SiC fiber, the SiC matrix, or an interphase. A local or effective threshold describes the removal onset within a particular fiber-, matrix-, interphase-, or pore-dominated region and is affected by local energy absorption, heat dissipation, interface conditions, and fiber orientation. An experimentally fitted threshold is obtained from a measured relationship, such as the squared ablation diameter versus the logarithm of laser power or fluence, and depends on the beam profile, spot-size definition, pulse number, surface condition, and damage-detection criterion.
The dependence of the ablation threshold on pulse duration must be interpreted within the applicable laser material interaction regime. Under classical thermal-diffusion assumptions, such as an optically homogeneous, semi-infinite target, diffusion-controlled energy transport, and prescribed absorption and thermophysical properties, the threshold fluence may scale with the square root of pulse duration, . This relationship is mainly applicable when thermal diffusion governs the depth of the heated region and should not be extrapolated without modification to the femtosecond regime. Under femtosecond irradiation, nonlinear absorption, carrier or electron excitation, nonequilibrium carrier/electron–lattice energy transfer, plasma formation, and incubation effects can alter both the threshold value and its pulse-duration dependence. The pulse-duration comparison discussed by Zhai et al. [99] should therefore be interpreted within its specific modeling assumptions rather than as a universal scaling law. Although shortening the pulse duration generally limits heat diffusion during energy deposition, it does not necessarily imply a universally valid square-root dependence or an invariably lower threshold for every constituent and processing condition.
The wavelength dependence of the ablation threshold cannot be inferred from photon energy alone. Although shorter wavelengths provide higher photon energies and may promote optical absorption, electronic excitation, or photochemical reactions in certain materials, the resulting threshold also depends on wavelength-dependent absorptivity and reflectivity, pulse parameters, beam characteristics, surface condition, and the constituent exposed within the irradiated region. For the SiC/SiC composite investigated by Zhai et al. [99], the experimentally fitted effective threshold fluences at 355, 532, and 1064 nm were approximately 54.068, 19.578, and 2.292 Jcm−2, respectively (Figs. 7A–7C). Thus, under these specific nanosecond irradiations and fitting conditions, the fitted threshold increased rather than decreased as the wavelength became shorter. The highest value was approximately 23.6 times the lowest value, which does not represent a difference spanning multiple orders of magnitude. These results are therefore process- and material-specific and should not be interpreted as establishing a universal wavelength and threshold relationship. Separately, Li et al. [137] reported higher absorption efficiency and removal performance for femtosecond processing of SiC/SiC at 515 nm than at 1030 nm. This observation concerns a different pulse regime and process response and consequently does not establish a general ordering of ablation thresholds with wavelength (Fig. 7D).
The heterogeneous and anisotropic structure of SiC-CMCs produces spatially varying local removal conditions, requiring constituent-level, local/effective, and experimentally fitted thresholds to be distinguished. The individual constituents, including SiC fibers, the SiC matrix, carbonaceous interphases, and pores, may exhibit different removal-onset conditions. Typically, the oxidation or sublimation threshold of carbon fibers or a pyrolytic-carbon interphase is lower than that of silicon carbide [102]. Consequently, the lower-threshold constituent may be removed before the higher-threshold constituent under otherwise comparable local irradiation conditions. In a systematic study on the removal mechanisms of SiC/SiC by femtosecond laser ablation, Wei et al. [130] explicitly noted a sequential order and morphological difference in the removal of different regions (fiber-rich areas, matrix-rich areas), which fundamentally stems from variations in the local effective ablation threshold. Furthermore, fiber orientation, by affecting local energy deposition and heat dissipation, also introduces anisotropy in the effective ablation threshold. Accordingly, a threshold fitted from the overall ablation diameter may be governed by the earliest-responding constituent or local region and should not be interpreted as the intrinsic threshold of every fiber, matrix, and interphase constituent within the composite.
3.2 Surface topography and defect evolution
The surface and subsurface regions following laser machining provide observable evidence of the underlying physicochemical processes. Their morphological characteristics and the type, size, and distribution of defects are central to assessing component surface integrity and its potential influence on fatigue strength, surface stress state, corrosion resistance, and coating adhesion.
3.2.1 Typical surface morphology
Regarding the fundamental morphology of ablated surfaces, the spatial distribution of energy dictates the zonal structure. As demonstrated in the study by Tong et al. [138], the surface resulting from millisecond laser ablation can be distinctly divided into three zones based on temperature gradients: a central zone primarily composed of nanocarbon flakes, a transition zone scattered with spherical SiC particles, and a peripheral zone covered with re-solidified SiO2 powder (as shown in Fig. 8). This finding has been corroborated by the work of Pan [139] and Dang [140], among others.
Concurrently, the anisotropy of the material dictates the evolutionary pathway of the resulting morphology. The work of Liu et al. systematically revealed the decisive influence of fiber orientation on ablation behavior: the morphology of 0° fibers evolved through a sequence of filamentous connection, flattened ellipse, needle-like shape, to convex shape, while 90° fibers exhibited an evolution path from cylindrical bulge, lotus leaf shape, bud shape, to closed shape (as shown in Figs. 9A–9K) [101]. Jiao’s research further pointed out that in 3D needled regions, due to different heat transfer conditions, the ablation morphology was approximately circular and deeper than in the regular lay-up regions, once again emphasizing the core influence of the meso-structure [102].
The interplay between process advancement and material characteristics is even more pronounced in the morphology of precision-machined structures. For micro-holes, their quality improves with shorter laser pulse widths and process innovations. Micro-holes machined with CW lasers exhibit a pronounced bell-mouth shape, with walls covered by a thick, crack-riddled layer of oxide and recast material [141]. Nanosecond lasers show improvement, but issues of taper and recast layer persist [142]. Hybrid processes like waterjet-guided laser machining can significantly reduce taper, producing nearly vertical sidewalls [143]. Femtosecond lasers, combined with strategies like helical scanning, can achieve micro-holes with high aspect ratios, low taper, and smooth walls [143,144]. However, material anisotropy remains a persistent challenge: preferential heat conduction along fibers can lead to elliptical or irregular hole entrances. Strategies employing rotating or coupled multi-beam setups can effectively improve circularity and uniformity [103]. Regarding the micro-morphology of hole walls, studies indicate a strong correlation with the processing environment: walls of holes machined in air are often coated with a deposition layer composed of nano-sized flocculates, micron-sized particles, and amorphous/crystalline SiO2 [131,145]. In contrast, waterjet-guided or underwater processing effectively suppresses oxidation, yielding cleaner hole wall surfaces with elemental composition closer to the base material [70]. The influence of anisotropy is more direct for grooves and cut surfaces. Due to preferential heat conduction along the fiber axis, scanning parallel to the fiber direction produces narrow, deep grooves with steep sidewalls; scanning perpendicularly results in wide, shallow grooves with sloping sidewalls [89,90]. The start and end points of a groove exhibit entrance effects and exit effects due to abrupt changes in thermal boundaries [90]. During thick plate cutting, an inappropriate focus increment can lead to recast layer accumulation or surface tilt in the mid-to-lower sections of the kerf [146].
Functional surface structuring represents the advancement of laser processing beyond traditional material removal, moving towards micro/nano-manufacturing and surface engineering. Utilizing picosecond or femtosecond lasers, controllable fabrication of micro-groove arrays, micro-dimple arrays, and laser-induced periodic surface structures (LIPSS) on material surfaces is achievable. These structures can be employed to alter surface wettability, as demonstrated by Zhou et al. [145] who transitioned SiC-CMCs from hydrophobic to super hydrophilic. They can also be used to enhance mechanical interlocking, thereby significantly improving the bonding strength of environmental barrier coatings [147].
3.2.2 Evolution of key defects
Defects are detrimental byproducts of the coupled laser-induced thermal-mechanical effects, and understanding their evolution is central to quality control. These primarily include the recast layer, microcracks, and the HAZ, as illustrated in Fig. 10A.
Formation and evolution of the recast layer. The formation of the recast layer is the most direct consequence of photothermal effects. It consists of material that is melted or softened by the laser, which subsequently re-solidifies and adheres to the substrate or hole wall after the beam moves away. In a study on millisecond-laser trepanning, Liu et al. [101] systematically identified five typical recast layer morphologies: (1) a layered structure formed by the accumulation of splashed molten droplets; (2) an adherent type, where melt solidifies at fiber ends; (3) a thin-shell type, comprising a continuous film covering the ablation crater surface; (4) a bubble-type, formed by gas entrapment during melt solidification; and (5) a multi-layered structure resulting from the cumulative effect of multiple scans (Fig. 10B). The recast layer is typically highly oxidized (SiO2-rich), structurally porous, weakly bonded to the substrate, and filled with micropores and microcracks. Its thickness exhibits a direct positive correlation with the laser’s heat input. Control strategies include: employing ultrafast pulsed lasers to minimize melting at the source; utilizing assist gases or water jets to blow away/flush the molten material; optimizing the scan path (e.g., intermittent scanning) to mitigate heat accumulation [148]; and applying post-process methods like laser chemical etching for its removal [149].
Initiation and propagation of microcracks. The nucleation and propagation of microcracks are primarily attributed to thermal stress. The material undergoes rapid heating and expansion under laser irradiation, followed by rapid cooling and contraction due to the surrounding cooler material or auxiliary media, thereby generating significant tensile stress. Cracks initiate when this stress exceeds the local fracture strength of the material. Cracks are prone to initiate at the following vulnerable sites (Fig. 10C): (1) the fiber/matrix interface, where shear stress arises from the mismatch in their coefficients of thermal expansion; (2) the interface between the recast layer and the substrate, due to weak bonding and significant inherent property differences; (3) within the recast layer itself, caused by solidification shrinkage stress and gas expansion; and (4) at inherent material defects (e.g., pores, micro-flaws), which act as stress concentrators [96]. The propagation path of cracks is influenced by material anisotropy, potentially extending along interfaces (causing delamination) or propagating through the matrix. These cracks serve as primary origins for component fatigue failure. Controlling thermal stress is fundamental to crack suppression, achievable through methods such as reducing heat input, optimizing heating/cooling rates, and improving the material’s own toughness.
Nature and impact of the HAZ. The HAZ represents a more insidious threat than visible defects. It is the region of material that is not melted but undergoes high-temperature thermal cycles. Within this zone, while the SiC matrix may not undergo phase transformation, the critical interphase (e.g., PyC, BN) can suffer from oxidation, graphitization crystallization, or reactions with the matrix, leading to severe degradation of its shear strength [150]. Dang et al. [140] observed significant interphase damage in continuous wave laser ablation studies (Fig. 10D). The extent of the HAZ is also positively correlated with heat input, and its shape and depth exhibit anisotropy due to the anisotropic thermal conductivity of the material.
3.3 Physical and chemical reactions and evolution of elemental chemical bonds
The transient high-temperature and high-pressure conditions induced by laser irradiation drive vigorous chemical reactions and elemental redistribution on the material surface. These changes, which can be precisely captured via modern analytical techniques, serve as microscopic evidence for revealing the ablation mechanisms and assessing the extent of damage.
3.3.1 Physical and chemical reactions
The high temperatures generated during laser machining inevitably trigger vigorous chemical reactions in ambient air, with oxidation reactions being the most prominent and complex, accompanied by decomposition and sublimation. Concurrently, the material itself may undergo phase transformations and decomposition under these extreme thermal conditions. These chemical processes profoundly alter the composition, microstructure, and residual stress state of the machined surface, thereby determining its service performance, including corrosion resistance, fatigue strength, and impact resistance.
Oxidation kinetics and zonal characteristics are central to research. The oxidation of SiC follows a competitive mechanism between passive and active oxidation, the boundary of which is precisely defined by the local temperature and oxygen partial pressure. Under relatively low temperatures and sufficient oxygen partial pressure, passive oxidation [Eq. (1)] occurs. The resulting SiO2 may form a glassy state but more commonly exists in a loose, amorphous form [138,151,152]. At high temperatures or under low oxygen partial pressure (e.g., at the bottom of deep holes, in inert atmospheres), active oxidation [Eq. (2)] occurs, producing gaseous products and leading to sustained linear material loss. Wei et al. [153] observed distinct reaction zones in femtosecond laser ablation craters: the central ablation zone, with the highest temperature and relatively low oxygen partial pressure, was dominated by active oxidation; the peripheral zone, with lower temperature, was dominated by passive oxidation, forming a SiO2 over-layer (Fig. 11A); a transition zone existed between them. The environmental medium acts as a key switch for the type and extent of oxidation. Machining in air results in the most severe oxidation. In underwater or waterjet-guided laser processing, the water film reduces exposure to ambient oxygen and lowers the surface temperature through rapid cooling, thereby suppressing, but not necessarily eliminating, oxidative reactions. Studies by Wei et al. [68,154] both indicate that oxides formed during underwater machining are mostly loose, porous, weakly bonded coral-like structures, which are more easily removed in post-processing. This contrasts sharply with the dense, continuous oxide layers formed in air (Fig. 11B). Furthermore, involved chemical reactions may also include minor oxidations of carbon and silicon [Eqs. (3)–(5)] and the hydrolysis of silicon carbide [Eq. (6)].
The dual role of oxidation products requires a dialectical view. On one hand, a dense, continuous SiO2 layer can act as a barrier to oxygen diffusion, protecting the underlying material from further oxidation during subsequent service [155]. On the other hand, the SiO2 recast layer formed during laser machining, due to the significant mismatch in the coefficient of thermal expansion with the SiC matrix, generates substantial tensile stress during cooling, making it highly prone to cracking or spallation from the substrate [77]. These cracks not only act as stress concentrators but also become channels for corrosive media penetration, severely compromising the mechanical properties and lifespan of the component. Therefore, controlling oxidation, especially suppressing the formation of harmful thick recast layers, is a key objective for improving laser machining quality.
Phase transformations, decomposition, and elemental segregation occur in the central, extremely high-temperature zone of laser interaction. Silicon carbide undergoes thermal decomposition [Eq. (7)] at temperatures exceeding approximately 2700 °C. The carbon produced by decomposition may remain as graphite, while the silicon vapor may condense into nanoparticles or react with oxygen. Under extreme energy density, SiC may even sublime directly [Eq. (8)]. Dang et al. [140] observed the complete disappearance of the SiC matrix in the central region of CW laser ablated C/SiC, leaving only graphitized carbon fibers and redeposited nano-carbon particles (Fig. 11B). Due to the significantly higher saturated vapor pressure of Si compared to C, selective evaporation of elements often occurs during ablation, leading to a carbon-rich trend on the machined surface, particularly in the central ablation zone [153]. Additionally, the extremely high heating and cooling rates induced by the laser can promote the formation of metastable phases. Li et al. [137] found that green femtosecond laser ablation could promote the transformation of metastable 3C-SiC to the more stable 6H-SiC polytype, accompanied by grain refinement. This phase transformation may influence the local mechanical and thermal properties of the processed region.
3.3.2 Evolution of elemental chemical bonds
Changes in surface chemical composition and bonding states can be analyzed in detail using techniques such as Energy Dispersive X-ray Spectroscopy (EDS), X-ray Photoelectron Spectroscopy (XPS), and Raman spectroscopy.
Laser ablation first significantly alters the elemental distribution on the material surface. The elemental mapping and line scanning capabilities of EDS provide a visual representation of this spatial distribution. Analyses reveal a general, significant enrichment of oxygen (O) in the ablated region, while silicon (Si) and carbon (C) elements are redistributed due to selective evaporation (higher vapor pressure of Si) or participation in oxidation reactions [153]. For instance, the high-temperature central ablation zone may become relatively carbon-rich due to the preferential evaporation of Si, whereas the cooler peripheral region is enriched in both oxygen and silicon due to the formation of silicon dioxide (SiO2) from oxidation. Quantitative studies further elucidate the response of elemental content to process parameters. Li et al. [156] found that increasing laser power, which corresponds to higher energy input, intensifies the oxidation process, leading to a rise in surface oxygen content and a decrease in carbon content. Depth profiling of ablation cross-sections by Chen et al. [152] clearly shows a gradient decrease in oxygen content from the surface towards the interior (Figs. 12A and 12B). Micro-area compositional analysis of different recast layer features (e.g., carbon-rich layered structures and oxygen-rich porous bubble structures) also confirms significant variations in local thermal history and oxidation degree [101]. As shown in Fig. 12C, the morphology of different types of ablation products (spherical, spore-like particles) and corresponding EDS point analysis results, which provide specific elemental ratios (e.g., C:O:Si), directly correlate morphological features with chemical states.
Building upon elemental redistribution, laser ablation more profoundly alters the chemical bonding state of the surface, for which XPS provides crucial information. In pristine SiC-CMCs, silicon atoms are primarily bonded to carbon atoms via Si–C bonds, with the Si 2p electron binding energy located at approximately 100.5 eV. After laser irradiation, a new, strong peak emerges around 103.5 eV, which corresponds to Si–O bonds. This is direct evidence of the oxidation of SiC or residual elemental silicon to form SiO2 (typically amorphous) [124,147,157]. The intensity ratio of the Si–O peak to the Si–C peak can serve as a semi-quantitative indicator of the surface oxidation degree. Studies confirm that this ratio generally increases with laser power, indicating that higher energy input leads to more complete oxidation [141]. As shown in Fig. 13, a comparison of Si 2p and C 1s spectra before and after ablation (Fig. 13A), and spectral changes under different power levels (Fig. 13B), visually demonstrate the transformation from Si–C to Si–O bonds and the evolution of carbon bonding states. Concurrently, changes in the C 1s spectrum reveal the complex evolution of carbon phases: variations in the graphitic ordering of graphitic carbon (C–C, sp2) and the appearance of oxygen-containing functional groups such as C–O, C=O, and even O–C=O may be observed, indicating that carbon fibers or the pyrolytic carbon interphase also undergo oxidation during processing [141,153]. XPS depth profiling can further reveal the gradient variation of chemical bonding states with depth within the oxide layer.
The evolution of elements and chemical bonds ultimately leads to fundamental changes in the phase composition of the material surface. X-ray Diffraction (XRD) and Raman spectroscopy are core techniques for analyzing phase composition. XRD analysis shows that the surface typically contains multiple phases after laser ablation: residual original β-SiC (3C-SiC) phase, newly formed amorphous or crystalline SiO2 phases (e.g., cristobalite), and a carbon phase with an increased degree of graphitization [141,152]. The relative content of the SiO2 phase is positively correlated with the laser energy input. As shown in Figs. 14A and 14B, a comparison of XRD patterns before and after ablation clearly indicates the formation of the new SiO2 phase. A strong piece of evidence is that after removing the surface oxide layer with hydrofluoric acid (HF) etching, the XRD spectrum primarily shows only the diffraction peaks of C and SiC, confirming that the oxide layer resides on the very surface, beneath which lie the transformed carbon phase and the incompletely reacted matrix [101,141]. As shown in Figs. 14C and 14D, Raman spectroscopy is highly sensitive to carbon materials. The intensity ratio of the D band (~1350 cm−1, representing disordered carbon/defects) to the G band (~1580 cm−1, representing the graphitic lattice), ID/IG, is an effective indicator for assessing the graphitization degree of the carbon phase. Raman spectroscopy can also detect the polytype of SiC (e.g., the TO mode of 3C-SiC at ~796 cm−1 and the LO mode at ~972 cm−1) [137]. The thermal effect of the laser typically promotes the ordering of carbon materials, leading to a decrease in the ID/IG ratio [137]. Furthermore, the attenuation of characteristic SiC Raman peaks and the appearance of a broad band corresponding to amorphous SiO2 after ablation jointly corroborate the oxidation and amorphization processes in the surface layer [125,130].
3.4 Microstructure evolution and its impact on performance
Laser machining’s impact on SiC-CMCs extends far beyond the modification of surface morphology. The extreme thermal-mechanical coupling effects it induces propagate deep into the material, triggering complex and often irreversible evolution in critical microstructural components, including fibers, matrix, and interphases. The resulting surface and sub-surface damage constitute the fundamental physical basis determining the component’s ultimate macroscopic service performance, such as strength, toughness, and fatigue life.
Interface degradation represents the most detrimental manifestation of laser thermal damage. The interphase (PyC or BN) between the fiber and matrix is critical for achieving pseudo-ductile fracture. The transient high temperature from the laser causes: (1) PyC oxidation and graphitization: Generating CO/CO2 gases that escape, leaving voids at the interface and completely destroying bonding; simultaneously, the high temperature promotes structural ordering, weakening the bonding strength [158,159]. (2) BN interfacial reactions: Possibly forming low-melting-point borosilicate glasses [149,160]. (3) Thermal stress-induced damage: Huge thermal stresses act directly on the interface, inducing microcracks. Utilizing in-situ CT and digital volume correlation (DVC) techniques, Chen et al. [158] clearly observed that the strain field within the material under laser thermal loading was highly concentrated around interfaces and pores (as shown in Figs. 15A and 15B). This degradation leads to fibers fracturing flush with the matrix rather than pulling out in the processed region, causing the material’s fracture behavior to degenerate from ductile to brittle [159,161].
Direct damage occurs to the fibers and matrix. For carbon fibers, damage includes oxidation, sublimation, and thermal stress-induced fracture. Dang et al. [140] found that under laser ablation at ~3500 °C, only needle-like carbon fibers remained in the central high-temperature zone, indicating severe structural degradation. Assisted by supersonic airflow, mechanical erosion can exacerbate fiber damage, increasing the ablation rate by several times [162,163]. For SiC fibers, localized melting, recrystallization (grain coarsening), and oxidation may occur [156]. Damage to the SiC matrix is more complex: (1) Thermally induced microcracks: mismatch in coefficients of thermal expansion between phases, coupled with rapid thermal cycling stresses, induces microcrack networks within the matrix [102,133]. (2) Phase transformation and decomposition: At high energy densities, SiC undergoes thermal decomposition or sublimation [86,92]. (3) Oxidation and re-condensation: Surface oxidation generates SiO2, while internally evaporated material re-condenses to form a recast layer with vastly different composition and structure [96,149,164].
Pore structure evolution affects specialized functionalities. The internal pore network in SiC-CMCs is crucial for functions like transpiration cooling. Laser thermal action can cause pores to shrink, deform, or even heal, while thermal stress can induce new microcracks. Analysis by Chen et al. [158] indicates that matrix and pore evolution increases fluid flow resistance, reducing transpiration cooling efficiency. The altered pore and crack networks also provide pathways for environmental medium ingress, laying the groundwork for long-term failure. Furthermore, microscopic damage profoundly affects macroscopic mechanical properties. The most significant consequence is a qualitative change in fracture behavior and toughness. Interface failure prevents cracks from effectively initiating fiber pull-out. Even when room-temperature flexural strength retention is sometimes high, the load-displacement curve loses its long tail, and the fracture work is drastically reduced. The material loses its damage warning capability, and the fracture mode shifts from quasi-ductile to brittle [150].
It is noteworthy that laser-induced alterations to the microstructure also possess a dialectical nature. With ultrafast, precise control, they can be transformed into a positive tool for enhancing specific functional properties. Utilizing the cold processing characteristic of ultrafast lasers, meticulously designed micro-nano textures (e.g., grooves, dimple arrays) can be fabricated on the surface. For instance, Zhai et al. [147] demonstrated that micro-textures prepared by femtosecond laser could increase the bonding strength of environmental barrier coatings by approximately 5.5%. The coating adhered neatly within the micro-textures, whereas it completely spalled off in untreated areas (as shown in Fig. 15C). This modification significantly increases surface area and creates a mechanical interlocking structure.
Quantitative damage–performance links should distinguish thermal alteration, material loss, and subsequent mechanical response, because these quantities are not interchangeable. Yan et al. [71] investigated chemical microfluid-assisted laser-induced plasma micro-drilling of 2.5D C/SiC. Relative to laser-induced ablation, the HF-assisted process reduced the reported HAZ thickness by 78.12%–80.46%. This improvement accompanied a 5.81% increase in average tensile strength under the high-temperature conditions investigated. However, taper and surface condition also changed, so the strength improvement cannot be attributed exclusively to HAZ reduction. This result supports a process-specific association rather than a universal HAZ and strength relationship.
Residual strength should also be distinguished from damage tolerance. In the modified C/C–ZrC–SiC system, Xu et al. [150] reported an ablation depth of approximately 190.4 μm. The post-ablation flexural strength was 217.67 ± 44.12 MPa, only 3.57% below the as-prepared value. Nevertheless, the fracture response changed from pseudo-plastic to brittle. This example shows why high strength retention does not necessarily imply preservation of energy absorption or fracture behavior. The reported depth represents material removal, not HAZ depth or recast-layer thickness, and the modified composition limits extrapolation to conventional C/SiC or SiC/SiC.
Surface integrity and service-oriented evaluation. For aviation hot-end applications, machining quality should be assessed through a linked evaluation of surface geometry, subsurface integrity, and service-relevant response. Roughness, taper, HAZ thickness, and recast-layer morphology describe important aspects of the machined state, but none alone establishes preservation of structural reliability. Additional indicators should include the depth, density, orientation, and connectivity of subsurface cracks; fiber continuity and pull-out or fracture characteristics; interphase degradation and debonding; changes in pore connectivity; and the spatial distribution of residual stress. These indicators should be interpreted relative to the initial architecture and the intended loading and environment, rather than combined into an unvalidated universal quality score [13,79].
A service-oriented characterization plan should therefore combine complementary measurements. Cross-sectional microscopy and, where spatial resolution is sufficient, X-ray computed tomography can assess hidden damage and pore or crack connectivity. EDS, XPS, Raman spectroscopy, and XRD provide complementary information on elemental redistribution, oxidation, bonding states, and phase changes, as discussed in Section 3.3. Local hardness or modulus measurements can identify changes in near-surface mechanical response, but they cannot substitute for composite-level damage-tolerance testing. Raman- or diffraction-based residual-stress measurements require constituent-specific calibration, a suitable reference state, and attention to texture, phase overlap, and sampling depth; an uncalibrated spectral shift should not be interpreted directly as stress.
Mechanical assessment should extend from retained room-temperature strength to high-temperature tensile or flexural behavior, stiffness evolution, crack initiation and propagation, and work of fracture or other appropriately defined damage-tolerance measures. For hot-end components, priority durability endpoints include cyclic fatigue, creep or stress rupture, thermal cycling and thermal shock, and oxidation or water-vapor exposure under representative conditions. Where environmental barrier coatings are used, interfacial adhesion and coating cracking or spallation should be evaluated after relevant exposure, rather than inferred from the as-textured surface. For cooling holes or permeable structures, flow resistance, leakage, and cooling effectiveness are additional functional endpoints. These are proposed evaluation requirements, not properties demonstrated for every laser process reviewed here.
The quantitative examples discussed above illustrate the present evidence boundary. The HAZ reduction and high-temperature tensile-strength improvement reported for microfluid-assisted drilling of 2.5D C/SiC support a process-specific association [71], while the retained flexural strength and altered fracture response of modified C/C–ZrC–SiC [150] show that strength retention does not necessarily preserve damage tolerance. Neither example establishes a general relationship between laser-induced damage and fatigue life, creep resistance, or hot-end component lifetime. The modified material in Ref. [150] also provides qualified adjacent-system evidence rather than a direct durability benchmark for conventional C/SiC or SiC/SiC.
Establishing a damage-service relationship requires paired measurements on consistently prepared specimens. Unmachined controls, an appropriate reference machining route, and laser-machined specimens should be compared while controlling architecture, interphase, porosity, feature geometry, and exposure history. Damage descriptors and subsequent mechanical or environmental response should be measured for the same specimens, or for traceable matched groups, with replication and uncertainty reported. Such datasets would allow processing-induced changes to be separated from geometric stress concentration and manufacturing variability, and would support condition-specific acceptance limits. Until these relationships are validated, a visually clean surface or a small HAZ should be treated as an indicator of machining quality rather than proof of preserved service life.
4 Laser Ablation Processing of SiC-CMCs
The evolution of laser machining processes constitutes a history of innovation in response to the difficult-to-machine characteristics of SiC-CMCs. Its developmental trajectory clearly reveals two intertwined main themes: firstly, the continuous compression of the laser temporal scale, progressing from CW and nanosecond to picosecond and femtosecond regimes. The core objective is to maximally suppress thermal effects, achieving a paradigm shift from thermal processing to cold processing. Secondly, there is the synergistic integration of machining energy fields from singular to multiple forms, leading to the development of new hybrid configurations combining lasers with water and gases. This aims to address specific bottlenecks related to efficiency, quality, and geometrical complexity. This section will systematically review various laser machining processes, from conventional to state-of-the-art, providing an in-depth analysis of their principles, characteristics, research progress, and application scenarios, thereby offering comprehensive reference for process selection and innovation.
4.1 Continuous and quasi-continuous laser ablation
CW and quasi-continuous-wave (QCW) lasers, the latter typically employing millisecond-scale pulses, can support relatively high removal rates in rough machining and high-energy processing. Their sustained heat input also increases the risk of recast material, oxidation, and a pronounced HAZ. The central challenge is therefore to balance removal efficiency against thermal damage under the reported material and process conditions [77].
Nevertheless, severe thermal damage limits their application in the manufacturing of precision components. Sustained heat input typically generates thick recast layers, a wide HAZ, and significant taper in the machined region [141]. The recast layer is weakly bonded to the substrate and rich in microcracks, while oxidation or pyrolysis of the interphase (e.g., PyC) within the HAZ severely weakens the interfacial bonding strength. Consequently, the direct application of CW lasers in precision manufacturing is relatively limited.
To balance machining efficiency and quality, researchers have pursued optimization from three dimensions: assist gas selection, pulse parameter matching, and scan path planning. Regarding assist gases, Chen et al. [136] compared the effects of O2, N2, and He in QCW laser drilling. They found that reactive gases (air and O2) enhanced ablation and promoted surface oxidation, leading to increased taper. Inert gases (N2/He) suppressed excessive ablation and surface oxidation, thereby reducing taper and achieving an optimal balance between machining quality and efficiency (as shown in Figs. 16A1 and 16A2). Cao et al. [135] further confirmed that laser ablation efficiency in an oxygen atmosphere was relatively higher, but material oxidation was pronounced, and splatter was more significant. In contrast, nitrogen and helium atmospheres reduced ablation efficiency and splatter while also effectively suppressing oxidation (Fig. 16B).
In terms of pulse parameter optimization, QCW lasers achieve discrete control of heat input through millisecond-level pulse modulation. Liu et al. [161] employed Taguchi orthogonal design and a multi-objective genetic algorithm (MOGA-II) to optimize fiber laser trepanning parameters. They found that the defocus amount contributed 75.42% to the influence on taper, and the scanning speed contributed 32.93% to the HAZ thickness. To address material anisotropy, Zhang et al. [100] proposed an intermittent path loading strategy. By alternating the scan direction, heat accumulation was alleviated, resulting in a reduced HAZ and significant improvement in the morphology and quality of perforated structures. The ablation depth with CW lasers is significantly greater than that with pulsed lasers, but thermal damage is more severe. Chen et al. [152] found that the ablation depth in CW mode was greater than in pulsed mode, and the ablation products exhibited a distinct layered structure (Fig. 16C).
In specialized applications, CW and QCW lasers have shown favorable performance under the reported high-energy or high-throughput conditions. Research by Wang et al. [162,163] demonstrated that high-speed (Mach 3–6) transverse airflow, through enhanced convective cooling, creates an asymmetric surface temperature distribution. The synergistic effect of airflow shear force and laser thermochemical ablation increases the MaRR by 4–9 times compared with that under static-air conditions (as shown in Fig. 16D). Furthermore, Ferraris et al. [165] achieved pressureless local joining of SiC/SiC tubes to end plugs using a diode laser. The joint strength reached 2100 N, significantly higher than the 1200 N achieved with conventional furnace brazing.
4.2 Nanosecond laser ablation
Nanosecond lasers (pulse durations typically ranging from a few nanoseconds to several hundred nanoseconds) currently represent the most widely used pulsed laser sources in industrial applications. They can offer a useful balance among processing efficiency, equipment cost, and attainable machining quality under appropriate conditions. Since their pulse duration remains significantly longer than the material’s electron−phonon coupling time, the photothermal effect still dominates. However, the substantial reduction in single-pulse interaction time results in a notably smaller HAZ depth compared to CW lasers, laying the groundwork for higher precision machining. Current research focuses on the refined modeling of process parameters, strategies for addressing material anisotropy, and overcoming the inherent thermal effect limitations through hybrid approaches.
Conventional nanosecond laser machining refers to the direct ablation process without introducing external auxiliary energy fields. Its core research lies in establishing a predictable and controllable processing window. Process modeling and parameter optimization form the foundation for systematic application. Through methods like orthogonal experimental design and Response Surface Methodology (RSM), researchers have established quantitative or semi-quantitative models between laser parameters (average power/single-pulse energy, scanning speed, repetition rate, pulse duration, defocus distance) and key machining outcomes (blind hole depth, groove width/depth, taper, surface roughness). Jiao et al. [88,90,102,166] conducted systematic experiments and found a good linear relationship between the blind hole depth in 2.5D C/SiC and the number of laser scans within a certain range. Based on this, they achieved controllable ablation of 1.5 and 2 mm diameter circular and square blind holes (Figs. 17A1 and 17A2). Particularly valuable is the direct correlation they established between the simulated temperature field and the ablation zones: the low-temperature zone corresponds to edge oxidation, the medium-temperature zone to edge removal, and the high-temperature zone to central removal (Figs. 17B1–17B3).
Addressing material anisotropy is a key challenge for obtaining uniform machining results. Due to the significantly faster heat conduction along the fiber axis compared to the radial direction and the matrix, the local thermal history of the laser-material interaction is strongly dependent on fiber orientation. The research by Zhang et al. [89] confirmed that scanning parallel to the fiber direction leads to rapid heat conduction away from the interaction zone, resulting in narrow and deep grooves; scanning perpendicular to the fibers causes heat accumulation, forming wide and shallow grooves. To address this issue, innovative beam and path planning strategies have been proposed. Zhang et al. [100] proposed an intermittent scanning path. By breaking the chain of heat accumulation caused by continuous scanning, this strategy effectively reduced groove taper and HAZ thickness. More advanced is the approach by Rao et al. [103], who employed Spatial Light Modulation (SLM) technology to generate a rotating 13-beam coupled spot. This multi-beam coupling strategy created a more uniformly distributed W-shaped energy profile in the processing area, effectively counteracting the elliptical ablation tendency caused by anisotropic thermal conduction. This resulted in rounder, more regular ablation craters and significantly improved the circumferential uniformity of the machined morphology (Figs. 17C1 and 17C2).
To overcome the bottlenecks of large taper, thick recast layer, and severe wall contamination faced by single nanosecond lasers in drilling deep, high-quality holes in SiC-CMCs, various hybrid processes incorporating auxiliary energy fields have emerged. Among these, waterjet-guided laser machining (WJGL) demonstrates significant advantages through the synergy of a laser and a high-speed water jet [160,167,168]. Its core principle involves coupling a nanosecond laser beam into a coaxial high-speed water jet, utilizing total internal reflection to confine the optical path, thereby guiding the laser along the curved water filament to the workpiece. In this process, the water jet plays multiple critical roles: as an efficient coolant, it rapidly removes heat, significantly suppressing the HAZ; as a powerful scouring agent, it promptly clears molten material and vapor or plasma, preventing redeposition and plasma shielding effects, thereby enhancing machining efficiency and sidewall quality; simultaneously, as a light-guiding medium, the water jet provides an extended effective guiding length compared with the conventional free-space focal region, thereby supporting high-aspect-ratio machining within limits imposed by jet stability, optical attenuation, cavity geometry, and fluid drainage.
Numerous studies have confirmed the significant effectiveness of WJGL in improving hole quality. Compared to nanosecond laser drilling in air, WJGL effectively suppresses oxidation, producing micro-holes with higher aspect ratios, cleaner walls, and significantly reduced taper. Published observations indicate that WJGL can reduce oxidation, taper, and reaction-product accumulation under the reported conditions. Compared with nanosecond laser drilling in air, Li et al. [169] reported that no clearly detectable oxide-layer attachment was observed in the locally examined WJGL-machined hole-wall regions within the resolution and sampling scope of the reported SEM/EDS characterization; the measured elemental composition was also closer to that of the substrate. In contrast, holes machined by ultraviolet nanosecond lasers in air exhibited evident silicon-oxide deposition (Figs. 18A1–18A8). Yuan et al. [143] reported microholes with low taper, clean walls, limited detectable reaction-product accumulation, and no distinct HAZ in the examined regions within the reported characterization resolution after air predrilling and WJGL finishing (Figs. 18B1–18B6). These observations support reduced detectable oxidation and thermal alteration under the investigated conditions, rather than the universal absence of oxidation or subsurface damage over the entire hole wall.
Optimization of process parameters is key to ensuring the quality and efficiency of WJGL machining. Through systematic experiments, Bao et al. [128] identified machining time, power density, and water jet velocity as significant factors influencing micro-hole depth and morphology. They found an optimal water jet velocity to balance efficiency and quality, and for the first time, provided an in-depth explanation of the water jet splashing mechanism: excessively high jet velocity and machining depth can cause droplet splashing, jet distortion, or even breakup, severely disturbing laser transmission, which is a major bottleneck limiting its machining capability [128]. To address this, they proposed covering the workpiece surface with porous water-absorbing material to absorb splashing droplets, effectively enhancing jet stability and MRR.
To address issues like water film formation and jet instability in WJGL, further technological innovations have been proposed. Cheng et al. [108,109] innovatively introduced the coaxial gas-assisted laser water jet (CGALWJ) technique. The coaxial spiral gas flow prevents air intrusion into the water filament during the injection stage and effectively blows away the water film on the workpiece surface during the impingement stage, significantly extending the stable length of the water jet and increasing the effective machining area. Under the reported conditions, this technique produced grooves with an aspect ratio of 13.6 in 3 mm thick SiC/SiC composites and relatively uniform cross-sections; no fiber pull-out or recast layer was detected in the characterized regions within the reported resolution. The study by Hu et al. [69] systematically investigated the effects of parameters like laser power and scanning speed on the ablation depth, MRR, and taper angle in WJGL grooving, providing process guidance for groove machining.
For engineering applications, data-driven process optimization has begun to progress beyond one-factor analysis and response surface methodology. Wei et al. [170] used a multi-objective optimization framework to coordinate inlet/exit edge chipping, dimensional accuracy, and drilling time in waterjet-guided laser machining. Gao et al. [129] further used average power, scanning speed, and hatch spacing as inputs to a neural network for predicting machining quality. The model captured nonlinear parameter–response relationships, with a reported mean absolute error (MAE) of 0.054 and root mean square error (RMSE) of 0.067, while a separate physical simulation model was used to interpret the predicted trends. This study represents an important step from statistical fitting toward machine-learning-assisted offline optimization (Figs. 18C1–18C3). However, it should not be interpreted as a physics-informed neural network, because the governing equations were not embedded in the loss function or network architecture. Its demonstrated applicability also remains confined to the investigated material and parameter domain; independent validation across composite architectures, feature geometries, and laser systems is still required before such a model can support autonomous process control.
4.3 Picosecond laser processing
Picosecond lasers, with their unique pulse duration (~10−12 s), occupy a crucial niche in the machining of SiC-CMCs that balances efficiency and precision. Their pulse width approaches the material’s electron−phonon coupling time, placing the ablation mechanism in a transitional regime between photothermal and photochemical/plasma effects. The relative contribution of each pathway depends not only on pulse duration but also on wavelength, fluence, repetition rate, pulse overlap, and the optical and thermophysical properties of the fiber, matrix, and interphase. Through parameter optimization, heat accumulation can be reduced, although it is not necessarily eliminated. Under the reported process windows, picosecond lasers have shown a potentially useful balance between removal efficiency and surface quality. However, direct comparisons with nanosecond and femtosecond regimes remain study-specific because the material architecture, feature geometry, laser parameters, and removal-rate definitions differ among studies. Consequently, they exhibit significant potential in efficient precision drilling, grooving, and surface functionalization.
Picosecond lasers, particularly high average power systems, demonstrate distinct advantages in the efficient fabrication of high-aspect-ratio, low-damage micro-holes. The use of advanced path strategies like helical scanning is key. Research confirms that by optimizing parameters, a VRR as high as 2.5 mm3s−1 can be achieved, allowing for the rapid fabrication of inclined micro-holes in 3.3 mm thick SiC/SiC while attaining a hole wall roughness below 0.36 μm [144]. More importantly, under specific polarization states and parameters, regular, parallel laser-induced periodic surface structures (LIPSS) can form on the hole walls, which is beneficial for enhancing surface functional properties (Figs. 19A1–19A3). Process parameters decisively influence drilling quality: smaller helical pitch and line width aid in energy concentration, improving wall quality; whereas excessively long machining times or inappropriate scanning speeds can lead to efficiency reduction or quality deterioration due to debris and plasma shielding effects [166]. Numerical simulation provides a powerful tool for understanding this process. The established transient solid-liquid-gas multiphase coupling model can accurately predict hole evolution, entrance taper angle, and the distribution of the recast layer decreasing along the hole depth [97].
In micro-grooving, picosecond lasers have shown favorable morphology control within the reported parameter ranges. Systematic studies show that groove depth, width, and sidewall quality strongly depend on pulse energy, scanning speed, repetition rate, and number of scans [131,166,171]. Among these, repetition rate is a parameter with a complex influence: too low (e.g., <50 kHz) easily leads to the accumulation of oxidation products, clogging the groove; an optimal value exists (e.g., 200 kHz) to balance efficiency and quality; whereas an excessively high repetition rate can aggravate heat accumulation [131]. Pulse energy has the most significant effect on groove depth, but excessively high energy shifts the material removal mechanism from being dominated by plasma effects to photothermal effects, increasing thermal influence. Scanning strategy is also crucial, as shown in Figs. 19C1–19C4, where a helical scanning mode proved more suitable for drilling deep holes compared to a single circular scan [156].
Picosecond lasers exhibit unique appeal in surface functionalization. Their short-pulse characteristic enables both precise material removal and the induction of changes in surface chemical and physical structure. Utilizing picosecond lasers, Zhou et al. [145] fabricated multi-level micro-nano structures on C/SiC surfaces, including regular convex platelet structures (20–60 μm), agglomerated ablation products (1–5 μm), and nanoparticles (100–500 nm), successfully transitioning the material from hydrophobic to super hydrophilic (Figs. 19B1–19B3). Analysis indicates this transition results from the combined effect of laser-generated hydrophilic SiO2 and amorphous carbon, along with the capillary effect induced by the microstructure. Further investigating the thermal damage mechanisms in inclined hole drilling, Zhou et al. [144] confirmed that heat accumulation and tensile thermal stress can induce defects like recast layers, fiber fracture, and fiber debonding. Circularly polarized picosecond lasers can induce regular parallel stripe periodic structures on hole walls, achieving synergy between structural modification and damage control. Research by Zhang et al. [131] found that a surface condensate layer forms under all picosecond laser machining conditions, while the generation of a recrystallized SiC layer can be precisely controlled by laser parameters and micro-groove depth. The ablation products are mainly SiO2 smoke and recrystallized SiC powder, exhibiting a loose, porous nature, which can significantly improve the material’s subsequent machinability (Figs. 19D1–19D2).
4.4 Femtosecond laser ablation
Femtosecond lasers, with pulse durations on the order of 10−15 s, provide a promising route for reducing thermal effects in precision machining. Because their pulse duration can be shorter than the characteristic electron–phonon coupling time, energy deposition may precede substantial lattice heating under suitable irradiation conditions. Nonlinear absorption, plasma formation, Coulomb explosion, phase explosion, and subsequent thermal relaxation may all contribute to material removal. Consequently, thermal diffusion and HAZ formation can be restricted, but are not necessarily eliminated, particularly at high repetition rates or substantial pulse overlaps.
To meet the stringent requirements of film cooling holes, small diameter, large inclination angles, and high aspect ratios, conventional drilling methods fall short. Femtosecond lasers combined with advanced scanning strategies provide a promising route for fabricating these challenging features. Two-step helical drilling with an inclined spiral trajectory has been demonstrated at the laboratory scale (Figs. 20A1–20A3). Its core concept involves a two-step optimization: the first step uses a smaller-diameter laser beam performing helical scanning along a designed inclination angle to rapidly penetrate the material, creating a pilot hole with relatively high taper. This stage prioritizes efficiency and establishes a debris removal channel. The second step involves a second scan along the same trajectory with the same or optimized laser parameters to uniformly finish the hole wall, removing the recast layer and deposits to achieve the final geometric accuracy and surface quality. Studies by Yang et al. [172], Li et al. [173], and Yang et al. [174] have shown favorable performance of this method under the investigated conditions. These studies reported inclined holes in 3–5 mm thick SiC/SiC, with aspect ratios up to approximately 10, taper angles below 1°, limited observable thermal damage, and single-hole processing times of approximately 150–200 s (Figs. 20B1–20B5). The key to this process lies in the precise control of the beam’s inclined incidence, helical interpolation motion, and parameter matching between the two steps. These results indicate potential for further engineering development, although process repeatability, throughput, and component-scale robustness require additional validation.
The cold processing characteristic of femtosecond lasers also makes them highly suitable for precise surface treatment of materials. Yuan et al. [175] investigated the use of femtosecond lasers for polishing rough C/SiC surfaces. They found that using a large angle of incidence concentrates laser energy more on the microscopic surface asperities, achieving a peak-shaving and valley-filling effect through selective removal of the peaks. Additionally, the large incidence angle reduces the laser energy deposition inside the material, thereby mitigating oxidation and defects (Figs. 20C1–20C4). Zhai et al. [147] utilized a femtosecond laser to etch a regularly arranged array of micro-grooves on the SiC/SiC surface. These microstructures provided a strong mechanical interlocking (anchoring) effect during subsequent deposition of an environmental barrier coating (EBC). Scratch test results indicated that the critical adhesion force of the coating on the laser-textured area increased by approximately 5.5%, and the coating failure time was extended by 11.2%, significantly enhancing the EBC’s spallation resistance under thermal shock conditions.
In-process sensing is much less developed than offline process optimization. Zhang et al. [95] collected plasma fluorescence during femtosecond-filament grooving of SiC-CMCs and found that the Si I line at 390.55 nm reflected changes in material removal. As the number of scans increased from one to five, the measured groove depth increased from 39 to 205 μm, whereas the spectral intensity decreased, establishing an inverse, process-specific relationship between signal intensity and groove development. This study provides a proof of concept for in-process state estimation, but it used a single spectral feature and did not couple the signal to a machine-learning estimator or feedback controller. The effects of collection geometry, plasma shielding, sidewall confinement, and material heterogeneity on signal reliability should therefore be quantified before spectroscopy is used for robust closed-loop control. Future monitoring could fuse spectroscopic, thermal, acoustic, and vision signals with uncertainty-aware machine learning to distinguish normal depth evolution from oxidation, redeposition, and fiber/matrix-specific damage.
To further reduce oxidation and redeposition during deep-hole machining, combining femtosecond lasers with auxiliary physical fields may offer a synergistic effect. Water film/magnetic field-assisted femtosecond laser drilling exemplifies hybrid field assistance. Research by Gao et al. [151,176] shows that maintaining a thin water film on the workpiece surface under semi-immersion conditions provides continuous cooling and reduces exposure to ambient oxygen, thereby suppressing, but not necessarily eliminating, oxidative reactions. Simultaneously, a longitudinal magnetic field aligned with the laser axis can modify the motion of charged species in the plasma plume. More precisely, the Lorentz force, acts only on the velocity component perpendicular to the magnetic field. It can therefore constrain transverse charged-particle motion and radial plume expansion, whereas particles moving exactly parallel to the field are not directly deflected. Under the reported conditions, the resulting modification of plume transport was associated with reduced plasma shielding and splatter deposition on the hole walls (Figs. 20D1–20D5). Under the reported conditions, the combined water and magnetic fields improved hole geometry and substantially reduced observable oxidation on the hole walls.
Femtosecond laser dynamic wet etching (FLDWE) is a sequential hybrid process that combines physics first, chemistry later. Li et al. [149] first machined the workpiece with a femtosecond laser, then immersed it in a flowing NaOH solution. Oxides like SiO2 generated by the laser action are rapidly chemically etched and carried away by the NaOH solution. Under the reported conditions, this process substantially reduced the ultrathin recast layer and HAZ and produced a surface composition closer to that of the parent material. It therefore provides a promising route for applications requiring strict control of surface contamination, such as optics and semiconductor manufacturing.
4.5 Cross-study quantitative synthesis
Direct cross-study comparison of SiC-CMC laser machining requires the material system, laser parameters, scanning conditions, processing environment, removal metric, and quality indicator to be considered together. Table 2 therefore consolidates the process-parameter and outcome information into a single study-level synthesis. Material architecture and fabrication route are specified when reported in the original study, while wavelength, pulse duration, spot size, fluence or power density, pulse energy, average power, repetition rate, pulse overlap, scanning strategy, and auxiliary field are retained in their original definitions and units. Consistent with Section 3.1.1, MRR is used as the general category, whereas quantitative time-normalized values are identified specifically as LRR, VRR, or MaRR. Groove depth, groove width, removed cross-sectional area, processing time, and removal per pulse or pass are retained as separate descriptors and are not reclassified as removal rates. NR denotes information not reported in the cited study, whereas study-specific identifies outcomes that cannot be normalized reliably across studies. The organization by pulse regime is intended only to facilitate navigation and does not imply a performance ranking among continuous wave (CW), quasi-continuous wave (QCW), nanosecond (ns), picosecond (ps), and femtosecond (fs) processes.
The comparison shows quantitatively useful trends within individual process families, but does not justify a universal ranking across pulse regimes. Under 1 ms irradiation, the ablation depth increased from approximately 0.20 to 0.80 mm as the pulse count increased from 5 to 100 at the reported low peak power density [139]. Multi-objective optimization of fiber-laser trepanning reduced the average HAZ thickness from 124.972 to 77.4 μm [161]. For water-assisted nanosecond processes, the reported MRR ranged from 0.107–0.118 mm3·s−1 in coaxial waterjet-assisted drilling [143], while laser-microjet ablation reached approximately 0.28 mm3·s−1 under its best reported condition [160]. UV-nanosecond MLLS produced Sa = 366.92 nm over a 5 mm × 5 mm region in 117.58 s [146]. Picosecond rotary ablation reached approximately 2.5 mm3·s−1 while maintaining a reported hole-wall RaL below 0.36 μm [144], whereas femtosecond polishing reduced the average Ra from 1.92 to 0.92 μm under the validated optimized condition [175]. These values expose the efficiency–quality trade-off, but pulse duration cannot be isolated as the sole cause because material architecture, feature geometry, scan path, environment, and measurement definitions differ among studies.
Laser-mechanical hybrid processes require separate evaluation because laser ablation is used to create a sacrificial, more readily removable surface state rather than to produce the final surface directly. This distinction is important when interpreting the HAZ: a laser-modified layer may lower the load in the subsequent mechanical step, but any portion remaining after finishing can still constitute thermal or microstructural damage. In 2.5D C/SiC produced by chemical vapor infiltration, Qu et al. [177] used laser pre-ablation-assisted grinding to reduce the surface hardness before material removal. Relative to grinding without laser pretreatment, the maximum grinding force decreased by up to 50.9%, surface roughness decreased by approximately 33.3%, and interfacial debonding and fiber fracture were suppressed. The authors attributed these improvements to a transition from brittle fracture toward near-ductile removal in the laser-modified region. These results provide direct evidence that controlled laser pre-ablation can improve the machinability of C/SiC. Complementary process-transfer evidence has been reported for zirconia-toughened alumina, a neighboring monolithic ceramic system. Sun et al. [178] employed picosecond-laser pre-ablation to generate textured surfaces before grinding. Under the study-specific conditions, the maximum reductions in the normal and tangential grinding forces reached 82.4% and 95.6%, respectively, while increasing the grinding removal depth reduced the post-grinding HAZ area fraction to 7.9%. Because ZTA does not possess the fiber–matrix–interphase architecture of SiC-CMCs, these numerical values should not be transferred directly to C/SiC or SiC/SiC. Instead, this study provides adjacent-system evidence that the subsequent grinding allowance should be coordinated with the depth of the laser-modified layer. More generally, reductions in grinding force and roughness do not by themselves demonstrate complete removal of the HAZ or preservation of post-machining service performance. The finished surface should therefore still be evaluated for residual thermal modification, oxidation, microcracking, and property degradation.
5 Conclusions and Prospects
5.1 Conclusions
The evidence synthesized in this review can be separated into two levels. Findings consistently supported across multiple studies are that laser machining responses are jointly governed by energy-deposition conditions, constituent anisotropy, and the processing environment, and that increasing cumulative thermal input generally aggravates oxidation, recast-layer formation, HAZ development, and cracking. In contrast, the quantitative ranking of wavelength-dependent thresholds, scan-direction effects on MRR, and damage, service, and performance relationships remains condition-dependent because material architectures, feature geometries, measurement methods, and rate definitions differ. The following conclusions are therefore stated within these evidence boundaries, while exploratory directions are discussed separately in Section 5.2.
(1) Genealogy and refinement of mechanistic understanding. The available evidence supports a pulse-duration-dependent organization of the reported material-removal mechanisms. An increasingly detailed, although still condition-dependent, physical picture has emerged, ranging from predominantly photothermal ablation and melt pool dynamics with CW/long-pulse lasers [87,93,94,98] to the photothermal-photochemical synergy and anisotropic heat transfer with nanosecond lasers [88,99,135], and further to the increasing contributions from nonequilibrium electronic and plasma-mediated mechanisms, while remaining vigilant of thermal accumulation, with ultrafast lasers (picosecond [96,97,131] and femtosecond [67,137,153]). Multiple studies consistently indicate that material anisotropy, heterogeneous constituent properties [90,99,133], and the processing environment jointly modulate energy deposition and damage evolution (particularly oxygen) [65,135,153,154,161]. Numerical simulation has evolved from heat conduction models for homogeneous materials to high-fidelity multi-physics simulation tools incorporating meso-structure [99], multiphase flow [97], the two-temperature model with multi-timescale coupling [67], and fully-coupled fluid-thermal-ablation models [94]. These provide useful tools within their validated parameter ranges for mechanism research and process optimization [67,93,97,109].
(2) Systematization and hybridization of process innovation. To address the diverse requirements of efficiency, precision, quality, and cost, a diverse and evolving set of process strategies has been reported.
• CW/Long-pulse lasers: have demonstrated their utility under high-throughput or high-energy conditions in efficient rough machining [141,152] and the study of material behavior in extreme environments [87,91,93,94,150,179].
• Nanosecond lasers: as the most widely investigated regime for engineering-oriented applications, they are continuously pushing the efficiency-quality balance through a series of innovations: ultraviolet photochemical effects [66,146], waterjet guidance [69,70,134,143,160,169], two-step/multi-step rotary drilling [142,146,148], chemical assistance [71,154], and beam coupling [103,164,180].
• Ultrafast lasers: picosecond [96,97,131,144,145,171] and femtosecond lasers [95,137,149,151,157,172–176,181] provide promising routes for precision manufacturing under selected processing conditions. Hybrid processes like helical scanning [172,173], water-magnetic field assistance [151,176], and laser-dynamic wet etching [149] are demonstrating the potential for low-damage machining under selected laboratory conditions.
• Process optimization: data-driven process development currently spans statistically designed response-surface optimization [142,175,181,182], multi-objective optimization for waterjet-guided laser machining [170], and neural-network prediction combined with separate physical interpretation [129]. In-process plasma-fluorescence monitoring has also been demonstrated at the proof-of-concept level [95]. These advances mark a transition from trial-and-error toward prediction and process-state estimation. Nevertheless, the available evidence remains predominantly offline or open-loop; machine-learning-enabled multimodal monitoring and closed-loop adaptive control have not yet been established for SiC-CMC laser machining.
(3) Significant enhancement in oxidation and damage controllability. A deeper understanding of the competitive mechanisms of active/passive oxidation [153,154] has enabled the possibility of actively suppressing oxidation through environmental media control (water [68,70,154], protective gas [135]). Consensus has been reached on the formation mechanisms, detrimental effects, and evaluation methods for damages like the HAZ, recast layer, and microcracks [101,144,150,160]. Effective post-processing removal techniques, such as chemical etching [71,149], have been developed. Quality assessment has progressed from macroscopic morphology observation to a comprehensive multi-dimensional characterization encompassing microstructure, composition, chemical state, and even residual stress [70,131].
(4) Deep multi-disciplinary integration of research paradigms. Current research increasingly integrates experimental characterization, numerical simulation, and theoretical analysis. High spatiotemporal, resolution in-situ/ex-situ characterization [91,106,131,153] and high-fidelity multi-physics simulation [67,93,94,97] complement each other, jointly deepening understanding. Periodic high-quality reviews [77,157,183] effectively organize the field’s progress. Research now involves multiple disciplines including materials science, physics, optics, mechanics, chemistry, and computer science, exhibiting a highly interdisciplinary and integrated character.
5.2 Prospects
Despite substantial progress, the wider engineering use of laser machining for SiC-based ceramic matrix composites (SiC-CMCs) depends on more than demonstrating feasible material removal. Fig. 21 outlines six connected directions, spanning laser–material interactions, adaptive control, functional manufacturing, predictive modeling, equipment integration, and quality evaluation. To make this roadmap actionable, each direction is framed below as a specific research question and linked to measurable outcomes. Their maturity should also be distinguished: some are supported by experimental SiC-CMC studies, whereas attosecond processing, integrated additive–subtractive manufacturing, physics-informed neural networks (PINNs), and real-time digital twins remain exploratory in the literature reviewed here.
(1) In-depth investigation of ultrafast nonequilibrium dynamics and the pursuit of ultimate cold processing. How can ablation-threshold models be made transferable across C/SiC and SiC/SiC with different architectures and irradiation conditions? A first step is to distinguish constituent-specific thresholds from local or experimentally fitted effective thresholds, and single-pulse initiation from incubation and sustained removal. Studies should report the beam profile, wavelength, pulse duration, fluence, pulse number and overlap, environment, and initial material state. Thermal and, where appropriate, carrier–lattice models should use constituent-specific optical and transport properties and account for evolving absorption and shielding [67,97,99]. Their predictions should be tested on architectures and process conditions excluded from calibration, with uncertainty and applicability limits reported. Time-resolved spectroscopy, pump–probe measurements, and multiscale simulations may then help resolve energy deposition, carrier relaxation, lattice response, and material ejection. Here, “cold” processing denotes a reduced thermal footprint, not the absence of heating; its attainable limit under repeated, production-relevant irradiation remains to be established. Attosecond-laser machining of SiC-CMCs should therefore be presented as a prospective research tool, not an experimentally validated manufacturing route.
(2) Anisotropy-induced consistency and intelligent adaptive control of machining. Which signals can estimate removal state and damage risk reliably enough to support online parameter adjustment? Local variations in fiber orientation, porosity, and interphase condition make a single fixed parameter set unlikely to produce uniform quality across every feature. Plasma-fluorescence monitoring provides an initial process signal [95], while neural-network-assisted parameter optimization has demonstrated offline predictive capability [129]; neither alone establishes closed-loop control. A testable system should synchronize coaxial imaging, optical emission or thermal measurements with laser and motion data, calibrate the resulting estimates against independent measurements of geometry, chemistry, and subsurface damage, and use them to adjust parameters within a validated operating range. Matched comparisons with fixed-parameter machining should report dimensional accuracy, damage, repeatability, estimation error, sensing and control latency, and robustness to plume shielding, sensor drift, and changes in material architecture. Optical signals should remain damage indicators, rather than direct measurements of damage, until that relationship has been independently verified.
(3) Function–structure-integrated additive–subtractive manufacturing. Can complex cooling features and functional surface textures be produced while retaining the required structural and environmental performance? As illustrated in Fig. 21, potential control targets extend beyond shape to pore volume, crystal phase or texture, and interface state. Feature-level experiments should connect dimensional tolerances and surface condition to application-relevant outcomes such as flow resistance, cooling effectiveness, environmental-barrier-coating adhesion, and residual load-bearing capacity. Existing laser texturing studies provide evidence that surface modification can affect function, including coating bonding [147]. They do not, however, demonstrate an integrated additive–subtractive route for SiC-CMC components. Before such integration is claimed, studies need to establish compatible starting material states, interphase integrity, repeatable feature formation, and performance retention. Complex additive–subtractive manufacture is therefore an exploratory extension of the reviewed subtractive and surface-functionalization work.
(4) High-fidelity digital twins and intelligent process decision systems. Which material and interface parameters are necessary to predict both feature geometry and processing-induced damage, and how should uncertainty propagate between scales? Models should be evaluated against independent measurements beyond ablation depth, including lateral geometry and characterized thermal or subsurface damage. Parameter sensitivity and identifiability are especially important for absorption, anisotropic transport, interfacial heat transfer, and removal criteria. Reduced-order or physics-informed models could accelerate prediction and inverse process design, but their value must be demonstrated against experimentally validated numerical models on withheld materials and process conditions. Relevant benchmarks include prediction error, uncertainty calibration, computational latency, and out-of-domain performance. The neural-network-based optimization reported in [129] is not a PINN, because governing equations were not enforced during network training. No direct application of a PINN or synchronized, closed-loop digital twin to SiC-CMC laser ablation was identified among the studies reviewed here; both remain proposed capabilities rather than established results.
(5) Green, robust, and engineerable integration of hybrid processes. Under which combinations of laser input, auxiliary medium, and finishing allowance can a hybrid process improve productivity while limiting or removing the affected layer? Waterjet-guided and chemical-assisted approaches should be assessed for transmission stability, cooling, debris removal, possible reactions, and resource consumption [71,109]. In laser–mechanical sequences, the finishing allowance should be related to the measured depth of the laser-modified region, rather than selected solely from the final roughness [72,177]. Comparisons should use matched material architectures and feature geometries and report final surface integrity, processing time, repeatability, energy and consumable use, waste handling, and post-processing requirements. Extended runs on representative features are needed to test equipment reliability and process stability. These measures will clarify whether laboratory-scale benefits persist under manufacturing conditions without assuming that auxiliary media eliminate oxidation or other damage.
(6) Standardized quality evaluation and an open process–performance database. How does laser-induced damage affect the service life of SiC-CMC components under coupled thermal, mechanical, and environmental loading? Paired damage–performance studies should measure, where relevant, subsurface cracks, fiber and interphase degradation, oxidation, recast material, and residual stress alongside fatigue, creep or stress-rupture behavior, thermal-cycling response, and coating durability. As-fabricated, reference-machined, and laser-machined specimens should be tested under matched conditions, with geometry, stress concentration, material variability, measurement resolution, and uncertainty recorded. Service-life models should be calibrated and independently tested on these paired data rather than inferred from roughness or heat-affected-zone thickness alone. An open database, consistent with Fig. 21, should link material system and fabrication history, processing parameters and sensor records, machining characteristics, quality and efficiency, mechanical properties, and in-service performance. Including failed and unstable trials would make the database more useful for external validation, transfer learning, and application-specific acceptance criteria.
In summary, laser machining technology for SiC-CMCs is at a critical juncture, transitioning from feasible to excellent, from empirical to scientific, and from singular manufacturing to system manufacturing. Through sustained breakthroughs in fundamental research and continuous innovation in engineering technology, laser machining is poised to provide robust and advanced manufacturing support for the broader application prospects of silicon carbide ceramic matrix composites, ultimately contributing to the advancement of the nation’s high-end equipment manufacturing industry.
CHANGE HISTORY
A Correction to this paper has been published: https://doi.org
The Retraction Note was updated to reflect reception of statements of disagreement from all authors.
This article has been retracted.Please see the Retraction Notice for more detail: https://doi.org
Chen Z W , Li Z Y , Li J J . et al. 3D printing of ceramics: a review. Journal of the European Ceramic Society, 2019, 39(4): 661–687
[2]
Galante R , Figueiredo-Pina C G , Serro A P . Additive manufacturing of ceramics for dental applications: a review. Dental Materials, 2019, 35(6): 825–846
[3]
Aveston J , Kelly A . Theory of multiple fracture of fibrous composites. Journal of Materials Science, 1973, 8(3): 352–362
[4]
Naik T P , Singh I , Sharma A K . Processing of polymer matrix composites using microwave energy: a review. Composites Part A: Applied Science and Manufacturing, 2022, 156: 106870
[5]
Hayat M D , Singh H , He Z . et al. Titanium metal matrix composites: an overview. Composites Part A: Applied Science and Manufacturing, 2019, 121: 418–438
[6]
Liao Z R , Abdelhafeez A , Li H N . et al. State-of-the-art of surface integrity in machining of metal matrix composites. International Journal of Machine Tools and Manufacture, 2019, 143: 63–91
[7]
Samant A N , Dahotre N B . Laser machining of structural ceramics—a review. Journal of the European Ceramic Society, 2009, 29(6): 969–993
[8]
Bilal A , Jahan M P , Talamona D . et al. Electro-discharge machining of ceramics: a review. Micromachines, 2019, 10(1): 10
[9]
Binner J , Porter M , Baker B . et al. Selection, processing, properties and applications of ultra-high temperature ceramic matrix composites, UHTCMCs-a review. International Materials Reviews, 2020, 65(7): 389–444
[10]
Gavalda Diaz O , Axinte D A. . Towards understanding the cutting and fracture mechanism in Ceramic Matrix Composites.. International Journal of Machine Tools and Manufacture, 2017, 118–119: 12–25
[11]
Frazer D , Abad M D , Krumwiede D . et al. Localized mechanical property assessment of SiC/SiC composite materials. Composites Part A: Applied Science and Manufacturing, 2015, 70: 93–101
[12]
Bernachy-Barbe F , Gélébart L , Bornert M . et al. Characterization of SiC/SiC composites damage mechanisms using Digital Image Correlation at the tow scale. Composites Part A: Applied Science and Manufacturing, 2015, 68: 101–109
[13]
Gavalda Diaz O , Garcia Luna G , Liao Z R . et al. The new challenges of machining Ceramic Matrix Composites (CMCs): review of surface integrity. International Journal of Machine Tools and Manufacture, 2019, 139: 24–36
[14]
Tong Y G , Hu Y L , Liang X B . et al. Carbon fiber reinforced ZrC based ultra-high temperature ceramic matrix composite subjected to laser ablation: ablation resistance, microstructure and damage mechanism. Ceramics International, 2020, 46(10): 14408–14415
[15]
Shen P F , Zhuang Y P , Jiang S D . et al. Experimental and numerical investigation on the ablation mechanism of Al2O3/Al2O3-CMCs under continuous-wave laser irradiation. Journal of the European Ceramic Society, 2022, 42(5): 2307–2318
[16]
Du J G , Zhang H Z , Geng Y M . et al. A review on machining of carbon fiber reinforced ceramic matrix composites. Ceramics International, 2019, 45(15): 18155–18166
[17]
Bernachy-Barbe F , Gélébart L , Bornert M . et al. Anisotropic damage behavior of SiC/SiC composite tubes: multiaxial testing and damage characterization. Composites Part A: Applied Science and Manufacturing, 2015, 76: 281–288
[18]
Sommers A , Wang Q , Han X . et al. Ceramics and ceramic matrix composites for heat exchangers in advanced thermal systems—a review. Applied Thermal Engineering, 2010, 30(11-12): 1277–1291
[19]
Ogi K , Okabe T , Takahashi M . et al. Experimental characterization of high-speed impact damage behavior in a three-dimensionally woven SiC/SiC composite. Composites Part A: Applied Science and Manufacturing, 2010, 41(4): 489–498
[20]
Chen J , An Q L , Chen M . Transformation of fracture mechanism and damage behavior of ceramic-matrix composites during nano-scratching. Composites Part A: Applied Science and Manufacturing, 2020, 130: 105756
[21]
Choudhary A , Das Chakladar N , Paul S . Identification and estimation of defects in high-speed ground C/SiC ceramic matrix composites. Composite Structures, 2021, 261: 113274
[22]
Zhou K , Xu J Y , Xiao G J . et al. A novel low-damage and low-abrasive wear processing method of Cf/SiC ceramic matrix composites: laser-induced ablation-assisted grinding. Journal of Materials Processing Technology, 2022, 302: 117503
[23]
Zhu W , Fu H , Xu Z F . et al. Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology. Journal of the European Ceramic Society, 2018, 38(14): 4604–4613
[24]
Skinner T , Rai A , Chattopadhyay A . Multiscale ceramic matrix composite thermomechanical damage model with fracture mechanics and internal state variables. Composite Structures, 2020, 236: 111847
[25]
Zhang D X , Liu Y , Liu H L . et al. Characterisation of damage evolution in plain weave SiC/SiC composites using in situ X-ray micro-computed tomography. Composite Structures, 2021, 275: 114447
[26]
Swaminathan B , McCarthy N R , Almansour A S . et al. Microscale characterization of damage accumulation in CMCs. Journal of the European Ceramic Society, 2021, 41(5): 3082–3093
[27]
Yin J F , Xu J H , Ding W F . et al. Feasibility of polarized laser scattering in detecting the grinding-induced subsurface damage in SiCf/SiC ceramic matrix composite. Composite Structures, 2022, 291: 115660
[28]
Arai Y , Inoue R , Goto K . et al. Carbon fiber reinforced ultra-high temperature ceramic matrix composites: a review. Ceramics International, 2019, 45(12): 14481–14489
[29]
Wang P R , Liu F Q , Wang H . et al. A review of third generation SiC fibers and SiCf/SiC composites. Journal of Materials Science & Technology, 2019, 35(12): 2743–2750
[30]
Yang X , Feng C , Peng Z H . et al. Evolution of microstructure and mechanical properties of PIP-C/SiC composites after high-temperature oxidation. Journal of Asian Ceramic Societies, 2017, 5(3): 370–376
[31]
Gu J , Lee S H , Vu V H . et al. Fast fabrication of SiC particulate-reinforced SiC composites by modified PIP process using spark plasma sintering-effects of green density and heating rate. Journal of the European Ceramic Society, 2021, 41(7): 4037–4047
[32]
Xu H , Li L , Zheng R X . et al. Influences of the dip-coated BN interface on mechanical behavior of PIP-SiC/SiC minicomposites. Ceramics International, 2021, 47(11): 16192–16199
[33]
Wang X , Wang K J , Bai H . et al. Creep properties and damage mechanisms of 2D-SiCf/SiC composites prepared by CVI. Journal of Inorganic Materials, 2020, 35(7): 817–821
[34]
Bhatt R T , Jaskowiak M H . Creep and cyclic durability of CVI SiC/SiC composites. Journal of the European Ceramic Society, 2024, 44(7): 4437–4451
[35]
Qin Y M , Zheng C , Bi Y C . et al. The microstructure and strength evolution of the CVI SiC matrix of Xe-implanted SiCf/SiC composites. Ceramics International, 2025, 51(6): 7693–7705
[36]
Caccia M , Narciso J . Key parameters in the manufacture of SiC-based composite materials by reactive melt infiltration. Materials, 2019, 12(15): 2425
[37]
Bhatt R T , Sola-Lopez F , Halbig M C . et al. Thermal stability of CVI and MI SiC/SiC composites with Hi-Nicalon™-S fibers. Journal of the European Ceramic Society, 2022, 42(8): 3383–3394
[38]
Dong Z H , Yuan S F , Zhao C L . et al. Ultra-long-term high-temperature oxidation resistance of the prepreg-MI SiC/SiC composites. Ceramics International, 2026, 52(11): 16594–16603
[39]
Liu R J , Wang F , Zhang J P . et al. Effects of CVI SiC amount and deposition rates on properties of SiCf/SiC composites fabricated by hybrid chemical vapor infiltration (CVI) and precursor infiltration and pyrolysis (PIP) routes. Ceramics International, 2021, 47(19): 26971–26977
[40]
Zhang L , Lin H J , Sun Z Y . et al. Investigation of in-situ microstructural mechanical properties and thermal damage mechanisms of SiCf/SiC under CVI and PIP processes. Materials Characterization, 2025, 220: 114689
[41]
Yucong W , Fang Y , Yi Z . et al. Ultrahigh room and high-temperature mechanical properties of SiCf/SiC composites prepared by hybrid CVI and PIP methods: effects of PIP temperature. Composites Part A: Applied Science and Manufacturing, 2025, 188: 108502
[42]
Yuan W , Hu J B , Zhou L . et al. Effect of fiber argon heat treatment on microstructure and properties of SiC/SiC composites prepared by CVI+RMI. Ceramics International, 2025, 51(20): 31986–31995
[43]
Süß F , Schneider T , Frieß M . et al. Combination of PIP and LSI processes for SiC/SiC ceramic matrix composites. Open Ceramics, 2021, 5: 100056
[44]
Mehta K M , Kumar Pandey S , Shaikh V A . Unconventional machining of ceramic matrix composites-a review. Materials Today: Proceedings, 2021, 46: 7661–7669
[45]
An Q L , Chen J , Ming W W . et al. Machining of SiC ceramic matrix composites: a review. Chinese Journal of Aeronautics, 2021, 34(4): 540–567
[46]
Peng C , Zhao G L , Song X B . et al. Effect of diamond grain size on mechanical properties and cutting performance of PCD tool in milling of Cf/SiC composites. Materials Today Communications, 2025, 42: 111175
[47]
Zan Z L , Sun J , Bi K D . et al. Investigation of milling performance and removal process mechanism of 3D SiCf/C-SiC composites using brazed diamond tools. Journal of the European Ceramic Society, 2024, 44(6): 3588–3601
[48]
Cao X Y , Lin B , Zhang X F . A study on grinding surface waviness of woven ceramic matrix composites. Applied Surface Science, 2013, 270: 503–512
[49]
Zhang L F , Ren C Z , Ji C H . et al. Effect of fiber orientations on surface grinding process of unidirectional C/SiC composites. Applied Surface Science, 2016, 366: 424–431
[50]
Zhang C , Li H , Zhang X X . et al. Parameter optimization, machining quality, removal mechanism, and tool wear in ultrasonic-vibration-assisted micro-hole drilling process of Cf/SiC ceramic matrix composites. Ceramics International, 2025, 51(29): 60645–60656
[51]
Yang H T , Zhao G L , Nian Z W . et al. Anisotropy effects in micro-hole drilling of 2.5D-Cf/SiC composites: insights from nanoindentation and drilling experiments. Composites Part A: Applied Science and Manufacturing, 2025, 198: 109066
[52]
Gavalda-Diaz O , Manno R , Melro A . et al. Mode Ⅰ and Mode Ⅱ interfacial fracture energy of SiC/BN/SiC CMCs. Acta Materialia, 2021, 215: 117125
[53]
Du J G , Ming W Y , Ma J . et al. New observations of the fiber orientations effect on machinability in grinding of C/SiC ceramic matrix composite. Ceramics International, 2018, 44(12): 13916–13928
[54]
Gavalda-Diaz O , Axinte D A , Novovic D . Probabilistic modelling of tool unbalance during cutting of hard-heterogeneous materials: a case study in Ceramic Matrix Composites (CMCs). Composites Part B: Engineering, 2018, 148: 217–226
[55]
Liu Y , Quan Y , Wu C J . et al. Single diamond scribing of SiCf/SiC composite: force and material removal mechanism study. Ceramics International, 2021, 47(19): 27702–27709
[56]
Zhang Y F , Liu D , Zhang W J . et al. Mechanism of Cf/SiC hole making with high shape precision using abrasive waterjet based on response surface method. Ceramics International, 2023, 49(3): 4129–4140
[57]
Zhang Y F , Liu D , Zhang W J . et al. Hole characteristics and surface damage formation mechanisms of Cf/SiC composites machined by abrasive waterjet. Ceramics International, 2022, 48(4): 5488–5498
[58]
Wei C J , Zhao L , Hu D J . et al. Electrical discharge machining of ceramic matrix composites with ceramic fiber reinforcements. The International Journal of Advanced Manufacturing Technology, 2013, 64(1): 187–194
[59]
Pachaury Y , Tandon P . An overview of electric discharge machining of ceramics and ceramic based composites. Journal of Manufacturing Processes, 2017, 25: 369–390
[60]
Wang J H , Chen X X , Xiao H P . et al. Theoretical and experimental investigation on PCD tool wear in longitudinal-torsional ultrasonic- and laser-assisted milling of 2.5D Cf/SiC composites. Tribology International, 2026, 218: 111760
[61]
Chen G J , Wang J Q , Fu K M . et al. Quality enhancement and defect suppression in SiC/SiC composites by ultrasonic vibration-assisted helical grinding. Materials Today Communications, 2025, 49: 114244
[62]
Sun H Q , Dong Z G , Yang F . et al. Tool wear mechanism in ultrasonic-assisted grinding of SiCf/SiC composites. Ultrasonics, 2026, 160: 107920
[63]
Sun Q X , Yin Z , An Q L . et al. Elucidating the influence of fibre orientation on material removal and grinding force in longitudinal torsional ultrasonic vibration-assisted grinding of SiCf/SiC composites. Precision Engineering, 2026, 100: 117–133
[64]
Ying E Z , Geng D X , Zhang D Y . et al. Influence of elliptical vibration on material removal and surface quality in rotary ultrasonic elliptical machining of Cf/SiC composites. Materials & Design, 2026, 262: 115500
[65]
Gao L , Liu C , Liu J J . Multi-pulse femtosecond laser ablation of SiC/SiC composites: morphological evolution, oxidation mechanisms and component characterization. Journal of Manufacturing Processes, 2024, 124: 316–333
[66]
Zhang F Y , Sun S F , Wang X . et al. Research on the ablation mechanism and feasibility of UV laser drilling to improve the machining quality of 2.5D SiC/SiC composites. Optics & Laser Technology, 2025, 181: 111754
[67]
Gao L , Liu C , Zhang D H . et al. Multi-pulse femtosecond laser ablation of SiC/SiC composites: temperature evolution and material removal considering dynamic defocusing effect. International Communications in Heat and Mass Transfer, 2026, 175: 111128
[68]
Wei J Y , Yuan S M , Zhang J Q . et al. Femtosecond laser ablation behavior of SiC/SiC composites in air and water environment. Corrosion Science, 2022, 208: 110671
[69]
Hu T R , Yuan S M , Wei J Y . et al. Water jet guided laser grooving of SiCf/SiC ceramic matrix composites. Optics & Laser Technology, 2024, 168: 109991
[70]
Wei J Y , Yuan S M , Yang S . et al. Waterjet-guided laser processing of SiC/SiC ceramic matrix composites to obtain high cleanliness and low oxidation damage characteristics surfaces. Surface and Coatings Technology, 2024, 484: 130791
[71]
Yan J W , Xu J Y , Hao B . et al. Performance evaluation of 2.5D C/SiC composite by chemical micro fluid assisted laser induced plasma micro-drilling. Optics & Laser Technology, 2026, 198: 114897
[72]
Niu F Y , Zhang Q H , Cai X T . et al. Mechanistic investigation of mechanical damage evolution in Cf/SiC composites via laser ablation-assisted ultrasonic layer-specific grinding. Journal of Materials Processing Technology, 2025, 342: 118948
[73]
Wang J H , Zhang C J , Jiao F . et al. Parameters optimization for 2.5D needled Cf/SiC in longitudinal torsional ultrasonic-assisted laser milling on PSO-BP-PSO. CIRP Journal of Manufacturing Science and Technology, 2025, 58: 87–106
[74]
Xiao G J , Yang Z Y , Zhou K . et al. Significant improvement of machinability of Cf/SiC composites through matching laser scanning spacing and abrasive belt grain size. Chinese Journal of Aeronautics, 2025, 38(1): 103017
[75]
Zhou K , Chen X Y , Li X . et al. Effect of laser-ablating assisted grinding process on subsequent tribological behavior of Cf/SiC composite. Journal of the European Ceramic Society, 2025, 45(12): 117434
[76]
Zivic F , Palic N , Jovanovic Z . et al. Processing routes for ceramic matrix composites (CMCs). Encyclopedia of Materials: Composites, 2021, 2: 20–36
[77]
Zhao C C , Sun G X , Wen M . et al. Fabrication and machining of the SiCf/SiC ceramic matrix composites: a review. Journal of Materials Research and Technology, 2026, 41: 2467–2499
[78]
Rayat M S , Gill S S , Singh R . et al. Fabrication and machining of ceramic composites—a review on current scenario. Materials and Manufacturing Processes, 2017, 32(13): 1451–1474
[79]
Qu S S , Yang Y Y , Yao P . et al. Fiber reinforced ceramic matrix composites: from the controlled fabrication to precision machining. International Journal of Extreme Manufacturing, 2025, 7(6): 062004
[80]
Zhang S S , Chen X X , Zhang W W . et al. Current status and development trend of laser processing of ceramic matrix composites. Journal of Materials Processing Technology, 2025, 342: 118940
[81]
Rocco P , Zucchetti M . Criteria for defining low activation materials in fusion reactor applications. Fusion Engineering and Design, 1991, 15(3): 235–244
[82]
Katoh Y , Snead L L , Henager C H Jr . et al. Current status and recent research achievements in SiC/SiC composites. Journal of Nuclear Materials, 2014, 455(1-3): 387–397
[83]
Bansal N P, Lamon J. Ceramic matrix composites: materials, modeling and technology. Hoboken: John Wiley & Sons, 2014
[84]
Eswara Prasad N, Kumar A, Subramanyam J. Ceramic matrix composites (CMCs) for aerospace applications. In: Eswara Prasad N, Wanhill R J H, eds. Aerospace Materials and Material Technologies. Singapore: Springer, 2017, 371–389
[85]
Wang L , Liu C T , Zhang Z L . et al. Investigating laser-induced thermal responses of C/SiC composites within airflow conditions. Case Studies in Thermal Engineering, 2024, 61: 105083
[86]
Ma T , Yuan W , Wang R X . et al. Ablation mechanisms of 2D C/SiC-Ti3SiC2 composite irradiated by combined laser: experimental and numerical study. Optics & Laser Technology, 2025, 181: 111859
[87]
Wang J R , Xie W H , Yan H . et al. Study on multi-scale ablation behavior of C/SiC composites under high-energy CW laser irradiation. Journal of the European Ceramic Society, 2024, 44(7): 4524–4535
[88]
Jiao H W , Chen B , Wang J . et al. Ablation of definite-depth blind holes in 2.5-dimensional C/SiC composites by nanosecond laser. Journal of Manufacturing Processes, 2023, 91: 78–88
[89]
Zhang T Y , Liu F , Liu Y . et al. Ultraviolet nanosecond laser-ablated groove analysis of 2.5D Cf/SiC composites. Crystals, 2023, 13(2): 223
[90]
Jiao H W , Chen B , Deng Z H . Influence of laser parameters on processing microgrooves of 2.5-dimensional C/SiC composites via nanosecond laser. The International Journal of Advanced Manufacturing Technology, 2022, 118(1): 85–101
[91]
Xu D D , Ai T C , Yang G J . et al. Surface and subsurface evolution mechanism in continuous wave laser ablation process of Cf/SiC ceramic matrix composites: a multiscale investigation. International Journal of Machine Tools and Manufacture, 2026, 214: 104354
[92]
Ma T , Wang R X , Qiu C . et al. Revealing the ablative behavior and mechanism of a 2D C/SiC Ti3SiC2 modified composite through a multi-scale laser ablation model. Ceramics International, 2024, 50(22): 47630–47648
[93]
Wang L , Liu C T , Zhang Z L . et al. “Temperature jump” study of C/SiC under high energy laser based on effective thermal conductivity. Applied Thermal Engineering, 2025, 263: 125086
[94]
Wang L , Liu C T , Zhang Z L . Damage evolution simulation and laser ablation mechanisms of C/SiC composites under in high-speed airflow environment. International Journal of Thermal Sciences, 2023, 194: 108596
[95]
Zhang J J , Zhang F S , Wang T J . et al. Femtosecond laser filament ablated grooves of SiC ceramic matrix composite and its grooving monitoring by plasma fluorescence. Ceramics International, 2024, 50(9): 16474–16480
[96]
Yang Z Y , Zhou K , Wu J . et al. Understanding laser ablating mechanism of Cf/SiC composites: micro heat transfer and subsurface microstructure transformation. Applied Surface Science, 2025, 681: 161514
[97]
Liu C , Li C , Gao L . et al. Micro-hole drilling of 2.5D C/SiC composite with picosecond laser: numerical modeling and experimental validation on hole shape evolution. Journal of Manufacturing Processes, 2022, 81: 852–864
[98]
Ma T , Song H W , Qiu C . et al. Laser ablation behavior of a 2-D C/SiC-Ti3SiC2 composite. Corrosion Science, 2023, 223: 111470
[99]
Zhai Z Y , Fan Q Y , Qu Y J . et al. Heat transfer mechanism of fiber reinforced composites processed by pulsed laser. Optics and Lasers in Engineering, 2023, 163: 107473
[100]
Zhang L , Xu J Y , Liu J H . et al. Heat transfer mechanism and ablation morphology of C/SiC processing based on laser path trajectory optimisation. Composites Part B: Engineering, 2025, 307: 112905
[101]
Liu C , Zhang X Z , Wang G F . et al. New ablation evolution behaviors in micro-hole drilling of 2. 5D Cf/SiC composites with millisecond laser. Ceramics International, 2021, 47(21): 29670–29680
[102]
Jiao H W , Chen B , Li S C . Removal mechanism of 2.5-dimensional carbon fiber reinforced ceramic matrix composites processed by nanosecond laser. The International Journal of Advanced Manufacturing Technology, 2021, 112(11): 3017–3028
[103]
Rao Q , Chen X X , Chen J B . et al. Processing characteristics and ablation mechanism of CMC-SiCf/SiC by rotational thirteen-beam coupling nanosecond laser. Ceramics International, 2024, 50(11): 20247–20259
[104]
Chopard B , Falcone J L , Kunzli P . et al. Multiscale modeling: recent progress and open questions. Multiscale and Multidisciplinary Modeling, Experiments and Design, 2018, 1(1): 57–68
[105]
Liu H G , Xu X , Zhang J . et al. The state of the art for numerical simulations of the effect of the microstructure and its evolution in the metal-cutting processes. International Journal of Machine Tools and Manufacture, 2022, 177: 103890
[106]
Zhang J Q , Yuan S M , Wei J Y . et al. Spatio-temporal multi-scale observation of the evolution mechanism during millisecond laser ablation of SiCf/SiC. Ceramics International, 2022, 48(16): 23885–23896
[107]
Cheng S , Geng L , Liu X C . et al. Laser ablation behavior and mechanism of C/SiC coated with ZrB2–MoSi2–SiC/Mo prepared by HVOF. Ceramics International, 2020, 46(11): 17752–17762
[108]
Cheng B , Ding Y , Li Y . et al. Coaxial helical gas assisted laser water jet machining of SiC/SiC ceramic matrix composites. Journal of Materials Processing Technology, 2021, 293: 117067
[109]
Cheng B , Ding Y , Li Y . et al. Theoretical and experimental investigation on SiC/SiC ceramic matrix composites machining with laser water jet. Applied Sciences, 2022, 12(3): 1214
[110]
Vakis A I , Yastrebov V A , Scheibert J . et al. Modeling and simulation in tribology across scales: an overview. Tribology International, 2018, 125: 169–199
[111]
Stavropoulos P , Chryssolouris G . Molecular dynamics simulations of laser ablation: the Morse potential function approach. International Journal of Nanomanufacturing, 2007, 1(6): 736
[112]
Prasad M , Conforti P F , Garrison B J . Coupled molecular dynamics-Monte Carlo model to study the role of chemical processes during laser ablation of polymeric materials. The Journal of Chemical Physics, 2007, 127(8): 084705
[113]
Zou Y , Cai J , Huai X L . et al. Molecular dynamics simulation of heat conduction in Si nano-films induced by ultrafast laser heating. Thin Solid Films, 2014, 558: 455–461
[114]
He X S , Chen R , Xie J . Anisotropic ablation mechanism of single crystal diamond surface in ultrafast laser processing: a molecular dynamics study. Optics & Laser Technology, 2025, 190: 113171
[115]
Zhang L B , Peng K , Gan Z Y . et al. Numerical simulation of ultrafast laser ablation on single crystal diamond by two-temperature model and molecular dynamics. Computational Materials Science, 2026, 262: 114383
[116]
Li J , Lu W N , Liu L . et al. Molecular dynamics simulation of microstructural evolution and mechanical behavior of titanium alloy subjected to laser shock peening. Optics & Laser Technology, 2024, 175: 110748
[117]
Gu Y , Han L L , Lin J Q . et al. Surface modification mechanism of laser-assisted grinding process for high silicon aluminum alloy: a molecular dynamics study. Surfaces and Interfaces, 2025, 56: 105753
[118]
Xie L Y , Li Y H , Wang F . et al. Molecular dynamics simulation study on the ablative copper forming process at the atomic level by femtosecond laser. Journal of Manufacturing Processes, 2025, 150: 38–47
[119]
Liu F , Cao S Y , Li B . et al. A molecular dynamics model for studying the effect of picosecond laser pulse overlap on silicon carbide ablation processing. Optics & Laser Technology, 2025, 186: 112702
[120]
Cui F J , Yang M H , Deng B . et al. Unraveling material removal mechanism in laser-assisted grinding of fused silica: molecular dynamics simulation of surface/subsurface evolution. Tribology International, 2026, 214: 111150
[121]
Li C , Hu Y X , Zhang F H . et al. Molecular dynamics simulation of laser assisted grinding of GaN crystals. International Journal of Mechanical Sciences, 2023, 239: 107856
[122]
Cui F J , Zhang H , Yang M H . et al. Molecular dynamics simulation and experimental study of laser-assisted machining of SiCp/Al composites. Procedia CIRP, 2025, 133: 2–7
[123]
He H Y , Xu J F , Wang X M . et al. Synergistic interfacial reinforcement in metal/composite joints: a molecular dynamics study. International Journal of Mechanical Sciences, 2026, 317: 111522
[124]
Zhai Z Y , Wang W J , Zhao J . et al. Influence of surface morphology on processing of C/SiC composites via femtosecond laser. Composites Part A: Applied Science and Manufacturing, 2017, 102: 117–125
[125]
Zhai Z Y , Wei C , Zhang Y C . et al. Investigations on the oxidation phenomenon of SiC/SiC fabricated by high repetition frequency femtosecond laser. Applied Surface Science, 2020, 502: 144131
[126]
Niu X M , Bian J , Chen X H . et al. Molecular dynamics simulation on PyC interfacial failure mechanism and shear strength of SiC/SiC composites. Modelling and Simulation in Materials Science and Engineering, 2021, 29(8): 085008
[127]
An H J , Wang J S , Fang F Z . Study on surface thermal oxidation of silicon carbide irradiated by pulsed laser using reactive molecular dynamics. The Journal of Chemical Physics, 2023, 158(10): 104702
[128]
Bao B Y , Zhang G Y , Chen Z A . et al. Splashing effects and mechanism in water jet-guided laser processing of Cf/SiC composites. Journal of Materials Processing Technology, 2025, 335: 118671
[129]
Gao M X , Yuan S M , Wei J Y . et al. Optimization of processing parameters for waterjet-guided laser machining of SiC/SiC composites. Journal of Intelligent Manufacturing, 2024, 35(8): 4137–4157
[130]
Wei J Y , Yuan S M , Zhang J Q . et al. Removal mechanism of SiC/SiC composites by underwater femtosecond laser ablation. Journal of the European Ceramic Society, 2022, 42(13): 5380–5390
[131]
Zhang C , Li H , Chen J . et al. Microstructure evolution and ablation mechanism of SiCf/SiC ceramic matrix composite microgrooves processed by pico-second laser. Ceramics International, 2023, 49(23): 37356–37365
[132]
Liu Y S , Zhang R H , Li W N . et al. Effect of machining parameter on femtosecond laser drilling processing on SiC/SiC composites. The International Journal of Advanced Manufacturing Technology, 2018, 96(5): 1795–1811
[133]
Wang J , Zhang Y H , Liu Y S . et al. Effect of SiC/SiC composites density on nanosecond-laser machining behaviors. Ceramics International, 2023, 49(3): 5199–5208
[134]
Bao B Y , Zhang G Y , Chen Z A . et al. Experimental investigation of water jet-guided laser micro-hole drilling of Cf/SiC composites. Materials, 2024, 17(9): 1975
[135]
Cao Y , Wang B , Li Z H . et al. The ablation behavior and mechanism of nanosecond laser machined SiCf/SiC composite under different assisted gases. Materials Characterization, 2025, 225: 115096
[136]
Chen S S , Bian Z G , Liu Z B . et al. Influence of assisted gases and parameters on quasi-continuous wave laser drilling of high aspect ratio micro-holes in SiCf/SiC composite. Journal of Materials Research and Technology, 2026, 41: 6936–6949
[137]
Li H , Yang J , Chen J . et al. Competitive and synergistic mechanisms of multiple physicochemical effects in femtosecond laser micro-etching process of SiCf/SiC composites. Journal of the European Ceramic Society, 2026, 46(12): 118393
[138]
Tong Y G , Bai S X , Zhang H . et al. Laser ablation behavior and mechanism of C/SiC composite. Ceramics International, 2013, 39(6): 6813–6820
[139]
Pan S N , Li Q Y , Xian Z K . et al. The effects of laser parameters and the ablation mechanism in laser ablation of C/SiC composite. Materials, 2019, 12(19): 3076
[140]
Dang X L , Yin X W , Fan X M . et al. Microstructural evolution of carbon fiber reinforced SiC-based matrix composites during laser ablation process. Journal of Materials Science & Technology, 2019, 35(12): 2919–2925
[141]
Zhang Y H , Liu Y S , Cao L Y . et al. Preparation and analysis of micro-holes in C/SiC composites and ablation with a continuous wave laser. Journal of the European Ceramic Society, 2021, 41(1): 176–184
[142]
Bai J X , Huang K R , Xu Z W . et al. An efficient near-zero taper UV nanosecond laser two-step drilling method for film cooling holes in SiCf/SiC composites. Optics & Laser Technology, 2026, 197: 114744
[143]
Yuan C H , Bian Z G , Cao Y . et al. Fabrication of micro-holes with high aspect ratios in Cf/SiC composites using coaxial waterjet-assisted nanosecond laser drilling. Micromachines, 2025, 16(7): 811
[144]
Zhou N , Yuan S M , Zhang W . et al. Revealing damage evolution and ablation behavior of SiC/SiC ceramic matrix composites by picosecond laser high-efficiency ablation. Journal of the European Ceramic Society, 2024, 44(8): 4949–4962
[145]
Zhou K , Xiao G J , Huang Y . Fabricating physicochemical microstructures with super hydrophilicity on Cf/SiC composites surface via picosecond-laser induced ablation. Ceramics International, 2023, 49(21): 34291–34302
[146]
Xu Z W , Jiang Y Y , Bai J X . et al. An efficient high-quality cutting method for thick SiCf/SiC ceramic matrix composites using UV laser multiline layered scanning with focus increment optimization. Journal of Materials Processing Technology, 2025, 335: 118674
[147]
Zhai Z Y , Wang W J , Mei X S . et al. Effect of the surface microstructure ablated by femtosecond laser on the bonding strength of EBCs for SiC/SiC composites. Optics Communications, 2018, 424: 137–144
[148]
Xu Z W , Bai J X , Qin N . et al. Focus increment-based laser-mechanical drilling process: a case study on film-cooling hole fabrication in SiCf/SiC composites.. Chinese Journal of Aeronautics, 2026, 104078
[149]
Li X Q , Yuan S M , Zhou N . et al. Investigation on femtosecond laser combined with dynamic wet etching machining of SiC/SiC. Journal of the European Ceramic Society, 2024, 44(12): 6839–6853
[150]
Xu J , Guo L J , Kong J G . et al. The mechanical properties of C/C-ZrC-SiC composites after laser ablation. Journal of the European Ceramic Society, 2023, 43(15): 6732–6745
[151]
Gao L , Liu C , Liu J J . Unraveling femtosecond laser drilling of slanted holes in SiC/SiC composites: morphological characterization, asymmetric oxidation mechanisms, and oxidation-free drilling processing. Journal of Materials Processing Technology, 2026, 352: 119320
[152]
Chen J , An Q L , Ming W W . et al. Investigations on continuous-wave laser and pulsed laser induced controllable ablation of SiCf/SiC composites. Journal of the European Ceramic Society, 2021, 41(12): 5835–5849
[153]
Wei J Y , Zhou N , Gao M X . et al. Laser ablation of SiC/SiC ceramic matrix composites: morphological characterization, component evolution and oxidation mechanisms. Corrosion Science, 2024, 227: 111762
[154]
Wei T , Sun S F , Zhang F Y . et al. Study on laser ablation and oxidation removal of SiCf/SiC composites in air and water. Journal of the European Ceramic Society, 2026, 46(12): 118374
[155]
Zhou N , Yuan S M , Gao M X . et al. Investigations on the oxidation behavior and removal mechanism of SiC/SiC composites by multi-pulse femtosecond laser ablation. Journal of Materials Research and Technology, 2023, 26: 3408–3425
[156]
Li W N , Zhang R H , Liu Y S . et al. Effect of different parameters on machining of SiC/SiC composites via pico-second laser. Applied Surface Science, 2016, 364: 378–387
[157]
Dong Z G , Ma H B , Ma G Y . et al. Femtosecond laser spiral scanning ablation of SiCf/SiC composites. Optics & Laser Technology, 2024, 176: 110958
[158]
Chen Z K , Li W , Ma Y . et al. Morphological evolution and internal strain mapping of 2.5D-C/SiC composite materials under laser load using X-CT and digital volume correlation. Materials Characterization, 2025, 229: 115553
[159]
Liu C , Zhang X Z , Gao L . et al. Study on damage characteristics and ablation mechanism in fiber laser trepan drilling of 2.5D Cf/SiC composites. The International Journal of Advanced Manufacturing Technology, 2021, 117(11): 3647–3660
[160]
Zhou N , Zhang W , Yuan S M . et al. Laser microjet ablation of SiC/SiC: phase transition, removal behavior, and damage evolution. Optics & Laser Technology, 2026, 193: 114206
[161]
Liu C , Zhang X Z , Gao L . et al. Feasibility of micro-hole machining in fiber laser trepan drilling of 2.5D Cf/SiC composite: experimental investigation and optimization. Optik, 2021, 242: 167186
[162]
Wang Z , Wang J T , Song H W . et al. Laser ablation behavior of C/SiC composites subjected to transverse hypersonic airflow. Corrosion Science, 2021, 183: 109345
[163]
Wang J T , Ma Y Z , Liu Y W . et al. Experimental investigation on laser ablation of C/SiC composites subjected to supersonic airflow. Optics & Laser Technology, 2019, 113: 399–406
[164]
Chen T , Chen X X , Liu G H . et al. Research on the ablation mechanism and ablation threshold of CMC-SiCf/SiC by using dual-beam coupling nanosecond laser. Ceramics International, 2022, 48(17): 24822–24839
[165]
Ferraris M , De Maddis M , Basile D . et al. Laser assisted joining of SiC/SiC for nuclear applications. Open Ceramics, 2025, 23: 100802
[166]
Jiao H W , Chen B , Luo L . et al. Ablation hole characteristic of 2.5-dimensional Cf/SiC composites processed by nanosecond laser. China Mechanical Engineering, 2020, 31(8): 983–990
[167]
Wen X L , Zhang X R . Recent development of water-jet guided laser processing. The International Journal of Advanced Manufacturing Technology, 2026, 143(11): 5995–6023
[168]
Zhang G Y , Li R , Rong Y M . et al. The influence mechanism of surface deformation and internal bubbles of microjet on laser transmission in waterjet-guided laser technology. Optics & Laser Technology, 2026, 194: 114414
[169]
Li P F , Wang Y H , Li L L . et al. Waterjet-guided laser drilling 2.5D Cf/SiC ceramic matrix composite material processing quality and removal mechanism analysis. Journal of Manufacturing Processes, 2026, 165: 293–305
[170]
Wei J Y , Gao M X , Fu Y Z . et al. Parameter study and multi-objective optimization for water jet guided laser drilling of SiC/SiC ceramic matrix composites. Journal of Materials Research and Technology, 2026, 41: 609–624
[171]
Li H , Zhang C , Chen J . et al. Surface microstructure evolution of Cf/SiC ceramic matrix composite microgrooves processed by ultrafast laser. Ceramics International, 2023, 49(18): 29477–29494
[172]
Yang F , Dong Z G , Li K . et al. Femtosecond laser processing inclined hole with large aspect ratio in SiCf/SiC composites. Journal of the European Ceramic Society, 2026, 46(12): 118378
[173]
Li Z J , Dong Z G , Yang F . et al. Femtosecond laser processing technology of inclined hole in SiCf/SiC composites. Optics & Laser Technology, 2025, 188: 112995
[174]
Yang F , Dong Z G , Kang R K . et al. Femtosecond laser rotary drilling for SiCf/SiC composites. Chinese Journal of Aeronautics, 2025, 38(2): 103056
[175]
Yuan C H , Wang B , Wang J J . et al. Effects of incidence angle and optimization in femtosecond laser polishing of C/SiC composites. Ceramics International, 2022, 48(21): 32290–32304
[176]
Gao L , Liu C , Liu J J . et al. Femtosecond laser drilling of SiC/SiC composites in longitudinal magnetic field and semi-water immersion assistance. Optics & Laser Technology, 2025, 181: 111955
[177]
Qu S S , Li L Y , Yang Y Y . et al. Surface roughness and damage evaluation of carbon fiber reinforced silicon carbide composites after laser ablation treatment and subsequent grinding. Journal of the European Ceramic Society, 2026, 46(6): 118082
[178]
Sun Y , Qu S S , Yang Y Y . et al. Laser pre-ablation assisted grinding process and material removal mechanisms of ZTA ceramics. Journal of Manufacturing Processes, 2026, 160: 345–358
[179]
Geng L , Cheng S , Guo C C . et al. Ablation behavior of C/SiC with YSZ and ZrB2 coatings under high-energy laser irradiation. Ceramics International, 2023, 49(2): 1700–1709
[180]
Rao Q , Chen X X , Li Q . et al. Research on parameter optimization of rotary beam coupled nanosecond-femtosecond laser hybrid surface processing technology of CMC-SiCf/SiC. Materials Today Communications, 2025, 49: 114115
[181]
Hu T R , Yuan S M , Wei J Y . et al. Micro-grooves machining and optimizing on SiC/SiC composites by femtosecond laser-based on response surface methodology. Ceramics International, 2024, 50(1): 1665–1682
[182]
Nian Z W , Zhao G L , Xin L J . et al. Laser-induced oxidation of Cf/SiC composites: oxidation behavior analysis and parameter optimization. Ceramics International, 2024, 50(18): 33445–33454
[183]
Sun D R , Wang G , Li Y F . et al. Laser drilling in silicon carbide and silicon carbide matrix composites. Optics & Laser Technology, 2024, 170: 110166