Influence of softening annealing on microstructural heredity and mechanical properties of medium-Mn steel

Abstract

Softening annealing (SA) is often required for producing medium-Mn steels (MMS) as it lowers hardness so that they can be cold rolled to reduce thickness. The influences of different SA processes on the microstructural heredity during the processing route and the final tensile properties were studied. It was found that the SA process could either intensify or weaken the influence of the Mn segregation resulting from solidification on the subsequent microstructural evolution during the process, i.e., microstructural heredity. In the case when no SA was employed, both recrystallization and rapid growth of ferrite grains preceded the reverse austenitic transformation during the intercritical annealing (IA) in the Mn-lean regions, where very coarse ferrite grains were formed. This deteriorated ductility due to the propagation of cracking along the boundary of the coarse-grained and fine-grained regions. In contrast, SA at a sufficiently high temperature could dissolve cementite, producing uniformly distributed austenite grains. They transformed to martensite during cold rolling but were reborn during IA. As a result, ultrafine austenite and ferrite grains were uniformly distributed, which improved ductility significantly. This study hints at a new approach to altering the microstructural heredity resulting from the heterogeneous Mn distribution in MMS.

Keywords

Medium-Mn steels / intercritical annealing / Mn segregation / recrystallization / mechanical properties

References

[1] Yang D,Wu D.The microstructure evolution and tensile properties of medium-Mn steel heat-treated by a two-step annealing process.2021;75:205-15

[2] Li X,Zhou N.An ultrahigh strength and enhanced ductility cold-rolled medium-Mn steel treated by intercritical annealing.Scripta Materialia2018;154:30-3

[3] Zhang X,Liu T.Microstructural evolution and mechanical behavior of a novel heterogeneous medium Mn cold-rolled steel.Materials Science and Engineering: A2021;800:140344

[4] Aydin H,Jung I.Development of 3rd generation AHSS with medium Mn content alloying compositions.Materials Science and Engineering: A2013;564:501-8

[5] Chiang J,Boyd J.Effect of microstructure on retained austenite stability and work hardening of TRIP steels.Materials Science and Engineering: A2011;528:4516-21

[6] Gibbs PJ,Merwin MJ,Speer JG.Austenite Stability Effects on Tensile Behavior of Manganese-Enriched-Austenite Transformation-Induced Plasticity Steel.Metall and Mat Trans A2011;42:3691-702

[7] Han J.The effects of the heating rate on the reverse transformation mechanism and the phase stability of reverted austenite in medium Mn steels.Acta Materialia2014;67:354-61

[8] Cai Z,Misra R.Austenite stability and deformation behavior in a cold-rolled transformation-induced plasticity steel with medium manganese content.Acta Materialia2015;84:229-36

[9] Chiang J,Pilkey A.Effect of microstructure on retained austenite stability and tensile behaviour in an aluminum-alloyed TRIP steel.Materials Science and Engineering: A2015;638:132-42

[10] Hu B.A novel two-step intercritical annealing process to improve mechanical properties of medium Mn steel.Acta Materialia2019;176:250-63

[11] Jang J,Kang NH,Suh D.Effects of annealing conditions on microstructure and mechanical properties of low carbon, manganese transformation-induced plasticity steel.Met Mater Int2009;15:909-16

[12] Lee S,De Cooman BC.Austenite stability of ultrafine-grained transformation-induced plasticity steel with Mn partitioning.Scripta Materialia2011;65:225-8

[13] Han J,Jung J.The effects of the initial martensite microstructure on the microstructure and tensile properties of intercritically annealed Fe–9Mn–0.05C steel.Acta Materialia2014;78:369-77

[14] Li Z,Zhang X.Annealing softening behaviour of cold-rolled low-carbon steel with a dual-phase structure and the resulting tensile properties.Materials Science and Engineering: A2012;552:204-10

[15] Benzing JT,Mates SP,Raabe D.Intercritical annealing to achieve a positive strain-rate sensitivity of mechanical properties and suppression of macroscopic plastic instabilities in multi-phase medium-Mn steels.Mater Sci Eng A Struct Mater2021;803:140469 PMCID:PMC8176460

[16] Wu Y,Styles M,Hutchinson C.Cementite coarsening during the tempering of Fe-C-Mn martensite.Acta Materialia2018;159:209-24

[17] Yan S,Liang T.The effects of the initial microstructure on microstructural evolution, mechanical properties and reversed austenite stability of intercritically annealed Fe-6.1Mn-1.5Si-0.12C steel.Materials Science and Engineering: A2018;712:332-40

[18] Luo H,Huang M.Effect of intercritical annealing on the Lüders strains of medium Mn transformation-induced plasticity steels.2015;83:42-8

[19] Ding R,Huang M.Effect of pre-existed austenite on austenite reversion and mechanical behavior of an Fe-0.2C-8Mn-2Al medium Mn steel.Acta Materialia2018;147:59-69

[20] Cao W,Shi J,Hui W.Microstructure and mechanical properties of Fe–0.2C–5Mn steel processed by ART-annealing.Materials Science and Engineering: A2011;528:6661-6

[21] Li S,Li S,Wang Y.A novel medium-Mn steel with superior mechanical properties and marginal oxidization after press hardening.Acta Materialia2021;205:116567

[22] Sarkar A,Bandyopadhyay TK.Recrystallization behaviour and tensile properties of Al-added medium-Mn-steel at different deformation-annealing conditions.Materials Science and Technology2018;35:2054-68

[23] Zheng C.Interaction between recrystallization and phase transformation during intercritical annealing in a cold-rolled dual-phase steel: A cellular automaton model.Acta Materialia2013;61:5504-17

[24] Jo MC,Zargaran A.Exceptional combination of ultra-high strength and excellent ductility by inevitably generated Mn-segregation in austenitic steel.Materials Science and Engineering: A2018;737:69-76

[25] Yang DZ,Matlock DK.Ferrite recrystallization and austenite formation in cold-rolled intercritically annealed steel.MTA1985;16:1385-92

[26] Zhu Y,Luo H.Influence of Nb and V on Microstructure and Mechanical Properties of Hot-Rolled Medium Mn Steels.steel research int2018;89:1700389

[27] Sun B,Vanderesse N.Macroscopic to nanoscopic in situ investigation on yielding mechanisms in ultrafine grained medium Mn steels: Role of the austenite-ferrite interface.Acta Materialia2019;178:10-25

[28] Hu B,Tu X.Influence of lamellar and equiaxed microstructural morphologies on yielding behaviour of a medium Mn steel.Materialia2021;20:101252