Influence of Annealing Treatment on Microstructure Evolution and Mechanical Property of Friction Stir Weld AZ31 Mg Alloys

Abstract

In order to improve microstructure distribution and mechanical properties of Mg alloy joint by annealing treatment, die-casting AZ31 Mg alloy was successfully welded at rotation speed of 1 400 rpm and travel speed of 200 mm/min. The welded joints were annealed at 150–300 °C for 15–120 min and then were subjected to transverse tensile. The microstructure of annealed joints was analyzed by optical microscopy and electron backscatter diffraction. The experimental results indicate that (0001) texture intensity in stir zone significantly reduces and sharp transition of grain size is relieved in the interface between stir zone and thermo-mechanically affected zone after annealed at 200 °C for 30 min. Meanwhile, the elongation is increased from 7.5% to 13.0% and strength is increased slightly. It is because that annealing treatment can inhibit twin transformation and retain its ability to coordinate deformation during tensile deformation, which contributes to the improvement of plasticity. In addition, annealing treatment can increase the width of interfacial transition zone and lead to gradual transition of grain size between the SZ and TMAZ, which balances dislocation diffusion rate in different zone.

Keywords

magnesium alloys / friction stir welding / annealing treatment / texture distribution / plasticity

References

[1] Luo AA. Magnesium Casting Technology for Structural Applications[ J]. Jounal of Magnesium Alloys, 2013, 1(1): 2-22.

[2] Chen XP, Wang LX, Xiao R, et al. Comparison of Annealing on Microstructure and Anisotropy of Magnesium Alloy AZ31 Sheets Processed by Three Different Routes[J]. Jounal of Alloys and Compounds, 2014, 604(9): 112-116.

[3] Taylor GI. Plastic Strain in Metals[J]. Jounal of the Institute of Metals, 1938, 62: 307-324.

[4] Hector JLG, Trinkle DR, Yasi JA. First–principles Data for Solid–solution Strengthening of Magnesium: From Geometry and Chemistry to Properties[J]. Acta Materialia, 2010, 58(17): 5 704-5 713.

[5] Zhao B, Debroy T. Pore Formation during Laser Beam Welding of Die–Cast Magnesium Alloy AM60B Mechanism and Remedy[J]. Welding Journal Research Suppliment, 2001 204-210.

[6] Yang J, Wang D, Xiao BL, et al. Effects of Rotation Rates on Microstructure, Mechanical Properties, and Fracture Behavior of Friction Stir–welded (FSW) AZ31 Magnesium Alloy[J]. Metallurgical and Materials Transactions A, 2013, 44(1): 517-530.

[7] Mishra RS, Mahoney MW. Friction Stir Welding and Processing[J]. Materials Science & Engineering R Reports, 2005, 50(1–2): 1-78.

[8] Templeman Y, Hamu GB, Meshi L. Friction Stir Welded AM50 and AZ31 Mg Alloys: Microstructural Evolution and Improved Corrosion Resistance[J]. Materials Characterization, 2017, 126: 86-95.

[9] Park SHC, Sato YS, Kokawa H. Effect of Micro–texture on Fracture Location in Friction Stir Weld of Mg Alloy AZ61 during Tensile Test[J]. Scripta Materialia, 2003, 49(2): 161-166.

[10] Chang CI, Lee CJ, Huang JC. Relationship between Grain Size and Zener–Holloman Parameter during Friction Stir Processing in AZ31 Mg Alloys[J]. Scripta Materialia, 2004, 51(6): 509-514.

[11] Suhuddin UFHR, Mironov S, Sato YS, et al. Grain structure evolution during friction–stir welding of AZ31 magnesium alloy[J]. Acta Materialia, 2009, 57(18): 5 406-5 418.

[12] Mironov S, Onuma T, Sato YS, et al. Microstructure Evolution during Friction–stir Welding of AZ31 Magnesium Alloy[J]. Acta Mateialia., 2015, 100: 301-312.

[13] Liu DJ, Xin RL, Xiao Y, et al. Strain Localization in Friction Stir Welded Magnesium Alloy during Tension and Compression Deformation[ J]. Materials Science and Engineering A, 2014, 609: 88-91.

[14] Liu DJ, Xin RL, Yu HN, et al. Comparative Examinations on the Activity a Variant Section of Twinning during Tension and Compression of Magnesium Alloys[J]. Materials Science and Engineering A, 2016, 658: 229-236.

[15] Chowdhury SH, Chen DL, Bhole SD, et al. Friction Stir Welded AZ31 Magnesium Alloy: Microstructure, Texture, and Tensile Properties[J]. Metallurgical and Materials Transactions A, 2012, 44(1): 323-336.

[16] Liu DJ, Xin RL, Li ZY, et al. The Activation of Twinning and Texture Evolution during Bending of Friction Stir Welded Magnesium Alloys[ J]. Materials Science and Engineering A, 2015, 646: 145-153.

[17] Xin RL, Liu DJ, Xu ZR, et al. Changes in Texture and Microstructure of Friction Stir Welded Mg Alloy during Post–rolling and Their Effects on Mechanical Properties[J]. Materials Science and Engineering A, 2013, 582(11): 178-187.

[18] Lee CJ, Huang JC, Du XH. Improvement of Yield Stress of Friction–stirred Mg–Al–Zn Alloys by Subsequent Compression[J]. Scripta Materialia, 2007, 56(10): 875-878.

[19] Song B, Pan H, Chai LJ, et al. Evolution of Gradient Microstructure in an Extruded AZ31 Rod during Torsion and Annealing and Its Effects on Mechanical Properties[J]. Materials Science & Engineering A, 2017, 689: 78-88.

[20] Qin FM, Zhu H, Wang ZX, et al. Dislocation and Twinning Mechanisms for Dynamic Recrystallization of As–cast Mn18Cr18N Steel[J]. Materials Science & Engineering A, 2017, 684: 634-644.

[21] Mohan A, Yuan W, Mishra RS. High Strain Rate Superplasticity in Friction Stir Processed Ultrafine Grained Mg–Al–Zn Alloys[J]. Materials Science & Engineering A, 2013, 562: 69-76.

[22] Yuan W, Mishra RS, Carlson B, et al. Material Flow and Microstructural Evolution during Friction Stir Spot Welding of AZ31 Magnesium Alloy[J]. Materials Science & Engineering A, 2012, 543: 200-209.

[23] Wang XH, Wang KS. Microstructure and Properties of Friction Stir Butt–welded AZ31 Magnesium Alloy[J]. Materials Science & Engineering A, 2006, 431: 114-117.

[24] Shan Q, Ni DR, Xue P, et al. Improving Joint Performance of Friction Stir Welded Wrought Mg Alloy by Controlling Non–uniform Deformation Behavior[J]. Materials Science & Engineering A, 2017, 707: 426-432.

[25] Xin RL, Liu DJ, Shu XG, et al. Influence of Welding Parameter on Texture Distribution and Plastic Deformation Behavior of As–rolled AZ31 Mg alloys[J]. Journal of Alloys & Compounds, 2016, 670: 64-71.

[26] Fong KS, Danno A, Tan MJ, et al. Tensile Flow Behavior of AZ31 Magnesium Alloy Processed by Severe Plastic Deformation and Post–annealing at Moderately High Temperatures[J]. Journal of Materials Processing Technology, 2017, 246: 235-244.

[27] Kim WJ, Jeong HG, Jeong HT. Achieving High Strength and High Ductility in Magnesium Alloys Using Severe Plastic Deformation Combined with Low–temperature Aging[J]. Scripta Mateialia., 2009, 61(11): 1 040-1 043.

[28] Ovid’ko IA, Langdon TG. Enhanced Ductility of Nanocrystalline and Ultrafine–grained Metals[J]. Reviews on Advanced Materials Science, 2012, 30: 103-115.

[29] Yoo MH. Slip, twinning, and Fracture in Hexagonal Close–packed Metals[J]. Metallurgical and Materials Transactions A, 1981, 12(3): 409-418.

[30] Wu L, Agnew SR, Brown DW, et al. Internal Stress Relaxation and Load Redistribution during the Twinning–detwinning–dominated Cyclic Deformation of a Wrought Magnesium Alloy ZK60A[J]. Acta Materialia, 2008, 56(14): 3 699-3 707.

[31] Barnett MR. Twinning and the Ductility of Magnesium Alloys Part I: “Tension” Twins[J]. Materials Science & Engineering A, 2007, 464(1): 1-7.

[32] Liu Z, Xin RL, Wu X, et al. Improvement in the Strength of Friction–stir–welded ZK60 Alloys Via Post–weld Compression and Aging Treatment[J]. Materials Science & Engineering A, 2018, 712: 493-499.