Miller Cycle with Early Intake Valve Closing in Marine Medium-Speed Diesel Engines

Abstract

In this study, a one-dimensional simulation was performed to evaluate the performance of in-cylinder combustion to control NO _x emissions on a four-stroke, six-cylinder marine medium-speed diesel engine. Reducing the combustion temperature is an important in-cylinder measure to decrease NO _x emissions of marine diesel engines. The Miller cycle is an effective method used to reduce the maximum combustion temperature in a cylinder and accordingly decrease NO _x emissions. Therefore, the authors of this study designed seven different early intake valve closing (EIVC) Miller cycles for the original engine, and analyzed the cycle effects on combustions and emissions in high-load conditions. The results indicate that the temperature in the cylinder was significantly reduced, whereas fuel consumption was almost unchanged. When the IVC was properly advanced, the ignition delay period increased and the premixed combustion accelerated, but the in-cylinder average pressure, temperature and NO _x emissions in the cylinder were lower than the original engine. However, closing the intake valve too early led to high fuel consumption. In addition, the NO _x emissions, in-cylinder temperature, and heat release rate remarkably increased. Therefore, the optimal timing of the EIVC varied with different loads. The higher the load was, the earlier the best advance angle appeared. Therefore, the Miller cycle is an effective method for in-engine NO _x purification and does not entail significant cost.

Keywords

Medium-speed diesel engine / Miller cycle / Combustion / NO _x emission / Early intake valve closing (EIVC)

References

[1] Benajes J, Molina S, Novella R, Belarte E. Evaluation of massive exhaust gas recirculation and Miller cycle strategies for mixing-controlled low temperature combustion in a heavy duty diesel engine. Energy, 2014, 71: 355-366

[2] Cui Y, Hu Z, Deng K, Wang Q. Miller-cycle regulatable, two-stage turbocharging system design for marine diesel engines. Journal of Engineering for Gas Turbines and Power, 2014, 136(2): 1-8

[3] Dobos A, Kirkpatrick A. Quasidimensional modeling of diesel combustion using detailed chemical kinetics. Journal of Engineering for Gas Turbines and Power, 2017, 139(8): 1-14

[4] Dobrucali E. The effects of the engine design and running parameters on the performance of a Otto-Miller Cycle engine. Energy, 2016, 103: 119-126

[5] Feng L, Tian J, Long W, Gong W, Du B, Li D, Chen L. Decreasing NO_x of a low-speed two-stroke marine diesel engine by using in-cylinder emission control measures. Energies, 2016, 9(4): 1-16

[6] Georgiou C, Azimov U. Analysis and multi-parametric optimisation of the performance and exhaust gas emissions of a heavy-duty diesel engine operating on miller cycle. Energies, 2020, 13(14): 3724

[7] Gonca G, Sahin B. Effect of turbo charging and steam injection methods on the performance of a miller cycle diesel engine (MCDE). Applied Thermal Engineering, 2017, 118: 138-146

[8] Gonca G, Sahin B, Parlak A, Ust Y, Ayhan V, Cesur I, Boru B. Theoretical and experimental investigation of the Miller cycle diesel engine in terms of performance and emission parameters. Applied Energy, 2015, 138: 11-20

[9] He Y, Liu J, Sun D, Zhu B. Development of an aggressive miller cycle engine with extended late-intake-valve-closing and a two-stage turbocharger. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 2019, 233(2): 413-426

[10] Imperato M, Kaario C, Sarjovaara P, Larmi M. Split fuel injection and Miller cycle in a large-bore engine. Applied Energy, 2016, 162: 289-297

[11] Kyrtatos P, Hoyer K, Obrecht P (2013) Recent developments in the understanding of the potential of in-cylinder NO_x reduction though extreme miller valve timing. 26th CIMAC Congress, Shanghai, No. 225.

[12] Kyrtatos P, Hoyer K, Obrecht P, Boulouchos K. Apparent effects of in-cylinder pressure oscillations and cycle-to-cycle variability on heat release rate and soot concentration under long ignition delay conditions in diesel engines. International Journal of Engine Research, 2014, 15(3): 325-337

[13] Leng X, Wei S, Tian J, He S, Long W, Guo H, Zhang X, Zhong B, Li H. The influence of charge temperature on the combustion and NO_x emission of a medium speed diesel engine. Journal of Harbin Engineering University, 2014, 35(11): 1351-1357 (in Chinese)

[14] Li C, Wang Y, Jia B, Roskilly A. Application of Miller Cycle with turbocharger and ethanol to reduce NO_x and particulates emissions from diesel engine-a numerical approach with model validations. Applied Thermal Engineering, 2019, 159: 904-911

[15] Li T, Gao Y, Wang J, Chen Z. The Miller cycle effects on improvement of fuel economy in a highly boosted, high compression ratio, direct-injection gasoline engine: EIVC vs. LIVC. Energy Conversion Management, 2014, 79: 59-65

[16] Liu H, Ma J, Tong L, Ma G, Zheng Z. Investigation on the potential of high efficiency for internal combustion engines. Energies, 2018, 11(3): 513

[17] Liu H, Zhang H, Wang H, Zou X, Yao M (2016) A Numerical study on combustion and emission characteristics of marine engine through miller cycle coupled with EGR and water emulsified fuel. SAE Technical Paper 2016-01-2187. https://doi.org/10.4271/2016-01-2187

[18] Lucchini T, Della Torre A, D’Errico G, Onorati A, Maes N, Somers L, Hardy G. A comprehensive methodology for computational fluid dynamics combustion modeling of industrial diesel engines. International Journal of Engine Research, 2017, 18(1–2): 26-38

[19] Luo Q, Sun B. Effect of the Miller cycle on the performance of turbocharged hydrogen internal combustion engines. Energy Conversion Management, 2016, 123: 209-217

[20] Muzio L, Quartucy GC. Implementing NO_x control: Research to application. Progress in Energy and Combustion Science., 1997, 23(3): 233-266

[21] Nahim HM, Younes R, Nohra C, Ouladsine M. Complete modeling for systems of a marine diesel engine. Journal of Marine Science and Application, 2015, 14(1): 93-104

[22] Qi K, Feng L, Leng X, Du B, Long W. Simulation of quasi-dimensional combustion model for predicting diesel engine performance. Applied Mathematical Modelling, 2011, 35(2): 930-940

[23] Song E, Fan L, Chen C, Dong Q, Ma X, Bai Y. Influence of pre-injection control parameters on main-injection fuel quantity for an electronically controlled double-valve fuel injection system of diesel engine. Journal of Marine Science and Application, 2013, 12(3): 366-373

[24] Tadros M, Ventura M, Guedes Soares C. Optimization of the performance of marine diesel engines to minimize the formation of SOx emissions. Journal of Marine Science and Application, 2020, 19(3): 473-484

[25] Wang P, Tang X, Shi L, Ni X, Hu Z, Deng K. Experimental investigation of the influences of Miller cycle combined with EGR on performance, energy and exergy characteristics of a four-stroke marine regulated two-stage turbocharged diesel engine. Fuel, 2021, 300: 120940

[26] Yang Z, Xie H, Chen T, Wu Z, Zhao H. Effects of PFI/DI injection on combustion characteristics of miller-cycle gasoline engine. Journal of Central South University, 2019, 25(1): 52-59 (in Chinese)

[27] Zamboni G, Moggia S, Capobianco M. Hybrid EGR and turbocharging systems control for low NO_x and fuel consumption in an automotive diesel engine. Applied Energy, 2016, 165: 839-848

[28] Zeldovich Y, Barenblatt G, Sunyaew R. Selected Works of Yakov Borisovich Zeldovich, Volume I, 2014, Princeton, New Jersey: Princeton University Press, 404-410

[29] Zerom M, Gonca G. Multi-criteria performance analysis of dual miller cycle-Organic rankine cycle combined power plant. Energy Conversion Management, 2020, 221: 113121

[30] Zhao J. Research and application of over-expansion cycle (Atkinson and Miller) engines-A review. Applied Energy, 2017, 185: 300-319

[31] Zhu S, Liu S, Qu S, Deng K. Thermodynamic and experimental researches on matching strategies of the pre-turbine steam injection and the Miller cycle applied on a turbocharged diesel engine. Energy, 2017, 140: 488-505