Direct tension and fracture resistance curves of ultra high performance marine composite materials

Abstract

Fracture behavior is one of the most important, yet still little understood properties of ultra-high performance cementitious composites (UHPCC), a new marine structural engineering material. Research on the fracture and direct tension behavior of UHPCC was carried out. The constitution law of UHPCC was divided into three phases: pre-partial debonding, partial debonding, and pullout phases. A direct tension constitution law was constructed based on the proposed fiber reinforcing parameter as a function of fiber volume fraction, fiber diameter and length, and fiber bonding strength. With the definition of linear crack shape, the energy release rate of UHPCC was derived and the R-curve equation was calculated from this. Loading tests of UHPCC using a three-point bending beam with an initial notch were carried out. The predictions from the proposed R-curve were in good agreement with the test results, indicating that the proposed R-curve accurately describes the fracture resistance of UHPCC. Introduction of a fiber reinforcement parameter bridges the fracture property R-curve and micro-composites’ mechanics parameters together. This has laid the foundation for further research into fracture properties based on micro-mechanics. The proposed tension constitution law and R-curve can be references for future UHPCC fracture evaluation.

Keywords

ultra high performance / cementitious composites / fracture / resistance curve / direct tension

References

[1] Wecharatana M., Shah S. P. Slow crack growth in cement composites[J]. Journal of the Structural Division, 1982, 108(6): 1400-1413

[2] Wecharatana M., Shah S. P. Predictions of nonlinear fracture process zone in concrete[J]. Journal of Engineering Mechanics, 1983, 109(5): 1231-1246

[3] Zhang J., Li V. C. Simulation of crack propagation in fiber-reinforced concrete by fracture mechanics[J]. Cement and Concrete Research, 2004, 34(2): 333-339

[4] Mai Y. W. Cohesive zone and crack-resistance(R)-curve of cementitious materials and their fiber-reinforced composites[J]. Engineering Fracture Mechanics, 2002, 69(2): 219-234

[5] Visalvanich K., Naaman A. E. Fracture model for fiber reinforced concrete[J]. ACI Journal, 1983, 80(2): 128-138

[6] AVESTON J, COOPER A, KELLY A. The properties of fiber composites[C]//Conference proceedings of the National Physical Laboratory. [S.l.]: IPC Science and Technology Press Ltd, 1971.

[7] Hannant D. J., Hughes D. C., Kelly F. R. S. Toughening of cement and other brittle solids with fibres[J]. Phil Trans R Soc Lond, 1983, 310: 175-190

[8] Naaman A. E., Namur G., Alwan J. M., Najm H. Fiber pullout and bond slip I: analytical study, II: experimental validation[J]. ASCE J of Structural Engineering, 1991, 117: 2769-2800

[9] Morrison J. K., Shah S. P., Jenq Y. S. Analysis of fiber debonding and pullout in composites[J]. Journal of Engineering Mechanics, 1988, 114(2): 277-293

[10] Han S. M., Wu X. G. Ultimate shear capacity of prestressed girder of ultra high performance fiber reinforced concrete[J]. Journal of the Korea Society of Hazard Mitigation, 2008, 8(2): 51-58

[11] Barenblatt G. I. The mathematical theory of equilibrium cracks in brittle fracture[C]. Advances in Applied Mechanics, 1962, New York: Academic Press, 55-129

[12] Andrews E. H., Levy G. M. Solvent stress crazing in PMMA[J]. Polymer(Surrey), 1974, 15: 599-607

[13] Schinker M. G., Doell W. Interference optical measurements of large deformations at the tip of a running crack in a glossy thermoplastic[C]. 1979, London: Institute of Physics, 224-232

[14] Griffith A. A. The phenomena of rupture and flow in solids[J]. Philosophical Transactions, 1920, 221: 163-198