Enabling 4.6 V LiNi_0.6Co_0.2Mn_0.2O₂ cathodes with excellent structural stability: combining surface LiLaO₂ self-assembly and subsurface La-pillar engineering

Abstract

Although Ni-rich layered materials with the general formula LiNi_1-x-yCo_xMn_yO₂ (0 < x, y < 1, NCM) hold great promise as high-energy-density cathodes in commercial lithium-ion batteries, their practical application is greatly hampered by poor cyclability and safety. Herein, a LiNi_0.6Co_0.2Mn_0.2O₂ (NCM622) cathode modified with a surface self-assembling LiLaO₂ coating and subsurface La pillars demonstrates stabilized cycling at 4.6 V. The LiLaO₂-coated NCM622 benefits from the suppression of interfacial side reactions, which relieves the layer-to-rock salt phase transformation and therefore improves the capacity retention under high voltages. Moreover, the La dopant, as a pillar in the NCM622 lattice, plays a dual role in expanding the c lattice parameter to enhance the Li-ion diffusion capability, as well as suppressing Ni antisite defect formation upon cycling. Consequently, the dual-modified NCM622 cathode exhibits an initial Coulombic efficiency of over 85% and a high capacity of over 200 mAh g^-1 at 0.1 C. A specific capacity of 188 mAh g^-1 with a capacity retention of 76% is achieved at 1 C after 200 cycles within a voltage range of 3.0-4.6 V. These findings lay a solid foundation for the materials design and performance optimization of high-energy-density cathodes for Li-ion batteries.

Keywords

LiNi_0.6Co_0.2Mn_0.2O₂ cathode / surface coating / La pillars / high energy density / Li-ion batteries

References

[1] Asadi M,Abbasi P.A lithium-oxygen battery with a long cycle life in an air-like atmosphere.Nature2018;555:502-6

[2] Zhu X,Zhang Q.LiMnO₂ cathode stabilized by interfacial orbital ordering for sustainable lithium-ion batteries.Nat Sustain2021;4:392-401

[3] Niu Y,Zhou Y.Constructing stable Li-solid electrolyte interphase to achieve dendrites-free solid-state battery: a nano-interlayer/Li pre-reduction strategy.Nano Res2022;15:7180-9

[4] Yu Z,Cheng Y.Preset lithium source electrolyte boosts SiO anode performance for lithium-ion batteries.ACS Sustain Chem Eng2022;10:10351-60

[5] Pomerantseva E,Feng X,Gogotsi Y.Energy storage: the future enabled by nanomaterials.Science2019;366:eaan8285

[6] Cheng Y,Yu Z.Ternary Si-SiO-Al composite films as high-performance anodes for lithium-ion batteries.ACS Appl Mater Interfaces2021;13:34447-56

[7] Chi X,Di J.A highly stable and flexible zeolite electrolyte solid-state Li-air battery.Nature2021;592:551-57

[8] Ding Z,Xu S.Stable heteroepitaxial interface of Li-rich layered oxide cathodes with enhanced lithium storage.Energy Storage Mater2019;21:69-76

[9] Yu Z,Li Y.Lithium titanate matrix-supported nanocrystalline silicon film as an anode for lithium-ion batteries.ACS Appl Mater Interfaces2019;11:534-40

[10] Feng X,Gao B,He X.Lithiophilic N-doped carbon bowls induced Li deposition in layered graphene film for advanced lithium metal batteries.Nano Res2022;15:352-60

[11] Ke C,Zhang Y.Synergistic engineering of heterointerface and architecture in new-type ZnS/Sn heterostructures in situ encapsulated in nitrogen-doped carbon toward high-efficient lithium-ion storage.Adv Funct Mater2022;32:2205635

[12] Fan X,Zhang B.Crack-free single-crystalline Ni-rich layered NCM cathode enable superior cycling performance of lithium-ion batteries.Nano Energy2020;70:104450

[13] Kim H,Jeong HY,Cho J.A new coating method for alleviating surface degradation of LiNi_0.6Co_0.2Mn_0.2O₂ cathode material: nanoscale surface treatment of primary particles.Nano Lett2015;15:2111-9

[14] Hussain N,Tian B.Co₃Se₄ quantum dots as an ultrastable host material for potassium-ion intercalation.Adv Mater2021;33:e2102164

[15] Tsai P,Wolfman M.Single-particle measurements of electrochemical kinetics in NMC and NCA cathodes for Li-ion batteries.Energy Environ Sci2018;11:860-71

[16] Kim JH,Kim SJ,Sun YK.Degradation mechanism of highly Ni-Rich Li[NixCoyMn_1-x_-y]O₂ cathodes with x > 0.9.ACS Appl Mater Interfaces2019;11:30936-42

[17] Kim A,Bartsch T.Stabilizing effect of a hybrid surface coating on a Ni-Rich NCM cathode material in all-solid-state batteries.Chem Mater2019;31:9664-72

[18] Heenan TMM,Tan C.Identifying the origins of microstructural defects such as cracking within Ni-Rich NMC811 cathode particles for lithium-ion batteries.Adv Energy Mater2020;10:2002655

[19] Yu Z,Wan T.Synthesis and mechanism of high structural stability of nickel-rich cathode materials by adjusting li-excess.ACS Appl Mater Interfaces2020;12:40393-403

[20] Fan X,Ji X.Highly fluorinated interphases enable high-voltage Li-metal batteries.Chem2018;4:174-85

[21] Zhu Z,Hu H.Enhanced structural and electrochemical stability of LiNi_0.83Co_0.11Mn_0.06O₂ cathodes by zirconium and aluminum co-doping for lithium-ion battery.J Power Sources2021;498:229857

[22] Lee S,Jeong JH.Li₃PO₄ surface coating on Ni-rich LiNi_0.6Co_0.2Mn_0.2O₂ by a citric acid assisted sol-gel method: improved thermal stability and high-voltage performance.J Power Sources2017;360:206-14

[23] Han S,Fan C,Yu L.1,4-Dicyanobutane as a film-forming additive for high-voltage in lithium-ion batteries.Solid State Ionics2019;337:63-9

[24] Fu J,Wu B.Enhanced electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ cathode at high cutoff voltage by modifying electrode/electrolyte interface with lithium metasilicate.Electrochim Acta2017;246:27-34

[25] Yang J,Yin J.Structure integrity endowed by a ti-containing surface layer towards ultrastable LiNi_0.8Co_0.15Al_0.05O₂ for all-solid-state lithium batteries.J Electrochem Soc2016;163:A1530-4

[26] Wang Y,Liu S,Gao X.Na-Doped LiNi_0.8Co_0.15Al_0.05O₂ with excellent stability of both capacity and potential as cathode materials for li-ion batteries.ACS Appl Energy Mater2018;1:3881-9

[27] Yu Z,Zhao G,Tian B.Combining surface holistic Ge coating and subsurface Mg doping to enhance the electrochemical performance of LiNi_0.8Co_0.1Mn_0.1O₂ cathodes.ACS Appl Mater Interfaces2022;14:25490-500

[28] Huang Y,Fu H.Mg-pillared LiCoO₂: towards stable cycling at 4.6 V.Angew Chem Int Ed2021;60:4682-8

[29] Xue W,Li Y.Ultra-high-voltage Ni-rich layered cathodes in practical Li metal batteries enabled by a sulfonamide-based electrolyte.Nat Energy2021;6:495-505

[30] Li J,Zhang D,Li Z.An effective doping strategy to improve the cyclic stability and rate capability of Ni-rich LiNi_0.8Co_0.1Mn_0.1O₂ cathode.Chem Eng J2020;402:126195

[31] Du F,Wu L.Tailoring the Al distribution in secondary particles for optimizing the electrochemical performance of LiNi_0.8Co_0.1Mn_0.1O₂.Ceramics Inter2021;47:12981-91

[32] Zhang M,Zhang J,Gu L.Preparation and electrochemical characterization of La and Al Co-doped NCM811 cathode materials.ACS Omega2021;6:16465-71 PMCID:PMC8246467

[33] Yoon W,Jang D.Structural study of the coating effect on the thermal stability of charged MgO-coated LiNi_0.8Co_0.2O₂ cathodes investigated by in situ XRD.J Power Sources2012;217:128-34

[34] Hu D,Cao H.An effective strategy to control thickness of Al₂O₃ coating layer on nickel-rich cathode materials.J Electroanal Chem2021;880:114910

[35] Woo S,Amine K,Sun Y.Significant improvement of electrochemical performance of AlF₃-Coated LiNi_0.8Co_0.1Mn_0.1O₂ Cathode Materials.J Electrochem Soc2007;154:A1005

[36] Song HG,Kim KT.Enhanced electrochemical properties of Li(Ni_0.4Co_0.3Mn_0.3)O₂ cathode by surface modification using Li₃PO₄-based materials.J Power Sources2011;196:6847-55

[37] Cho W,Song JH.Improved electrochemical and thermal properties of nickel rich LiNi_0.6Co_0.2Mn_0.2O₂ cathode materials by SiO₂ coating.J Power Sources2015;282:45-50

[38] Liu Y,Wei H.Enhancement on structural stability of Ni-rich cathode materials by in-situ fabricating dual-modified layer for lithium-ion batteries.Nano Energy2019;65:104043

[39] Chen Y,Chen B,Lu C.An approach to application for LiNi_0.6Co_0.2Mn_0.2O₂ cathode material at high cutoff voltage by TiO₂ coating.J Power Sources2014;256:20-7

[40] Ahn J,Yoon S.Ultrathin ZrO₂ on LiNi_0.5Mn_0.3Co_0.2O₂ electrode surface via atomic layer deposition for high-voltage operation in lithium-ion batteries.Appl Surf Sci2019;484:701-9

[41] Huang X,Yao J.Suppressing structural degradation of Ni-rich cathode materials towards improved cycling stability enabled by a Li₂MnO₃ coating.J Mater Chem A2020;8:17429-41

[42] Yang H,Ge M.Simultaneously dual modification of ni-rich layered oxide cathode for high-energy lithium-ion batteries.Adv Funct Mater2019;29:1808825

[43] Ming Y,Qiu L.Dual elements coupling effect induced modification from the surface into the bulk lattice for ni-rich cathodes with suppressed capacity and voltage decay.ACS Appl Mater Interfaces2020;12:8146-56

[44] Wu L,Rong Z.Studies on electrochemical reversibility of lithium tungstate coated Ni-rich LiNi_0.8Co_0.1Mn_0.1O₂ cathode material under high cut-off voltage cycling.Appl Surf Sci2019;484:21-32

[45] Gan Z,Hu G.Surface modification on enhancing the high-voltage performance of LiNi_0.8Co_0.1Mn_0.1O₂ cathode materials by electrochemically active LiVPO₄F hybrid.Electrochim Acta2019;324:134807

[46] Fan Q,Yang S.Constructing effective TiO₂ nano-coating for high-voltage Ni-rich cathode materials for lithium ion batteries by precise kinetic control.J Power Sources2020;477:228745

[47] Li J,Lu X.Enhancing high-potential stability of Ni-rich LiNi_0.8Co_0.1Mn_0.1O₂ cathode with PrF3 coating.Ceram Int2021;47:6341-51

[48] Wang R,Zhang Q,Xu K.Enhanced electrochemical performance of La and F co-modified Ni-rich cathode.Ionics2020;26:1165-71

[49] Yang J,Li Y.A simple strategy to prepare the La₂Li_0.5Al_0.5O₄ modified high-performance ni-rich cathode material.Mater Chem Phys2020;249:123135

[50] Cheng Z,Xu N.Enhanced rate performance and cycle stability of LiNi_0.6Co_0.2Mn_0.2O₂ at high cut-off voltage by Li_6.1La₃Al_0.3Zr₂O₁₂ surface modification.Appl Surf Sci2020;524:146556

[51] Jung C,Eum D.New insight into microstructure engineering of Ni-rich layered oxide cathode for high performance lithium ion batteries.Adv Funct Mater2021;31:2010095

[52] Qu X,Wan T.An integrated surface coating strategy to enhance the electrochemical performance of nickel-rich layered cathodes.Nano Energy2022;91:106665

[53] Liu Y,Li G.The surface double-coupling on single-crystal LiNi_0.8Co_0.1Mn_0.1O₂ for inhibiting the formation of intragranular cracks and oxygen vacancies.Energy Storage Mater2022;52:534-46

[54] Han B,Zhao S.Enhancing the structural stability of Ni-Rich layered oxide cathodes with a preformed Zr-concentrated defective nanolayer.ACS Appl Mater Interfaces2018;10:39599-607

[55] Liu S,Zhao J.Uncovering the role of Nb modification in improving the structure stability and electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ cathode charged at higher voltage of 4.5 V.J Power Sources2018;374:149-57

[56] Kim U,Son B.Heuristic solution for achieving long-term cycle stability for Ni-rich layered cathodes at full depth of discharge.Nat Energy2020;5:860-9

[57] Fan X,Zhao W.In situ inorganic conductive network formation in high-voltage single-crystal Ni-rich cathodes.Nat Commun2021;12:5320 PMCID:PMC8423756

[58] Wei K,Wang S.Watermelon-like texture lithium titanate and silicon composite films as anodes for lithium-ion battery with high capacity and long cycle life.J Alloys Compd2021;885:160994

[59] Shi Y,Jiang P.Unlocking the potential of P3 structure for practical Sodium-ion batteries by fabricating zero strain framework for Na+ intercalation.Energy Storage Mater2021;37:354-62

[60] Yu Z,Wei J,Cheng Y.Improving electrode properties by sputtering Ge on SiO anode surface.Ceram Int2022;48:26784-90

[61] Yu Z,Tong J,Cheng Y.Improving electrochemical performance of thick silicon film anodes with implanted solid lithium source electrolyte.J Phys Chem Lett2022;13:8725-32

[62] Yang G,Lai F.Integrated co-modification of PO43- polyanion doping and Li₂TiO₃ coating for Ni-rich layered LiNi_0.6Co_0.2Mn_0.2O₂ cathode material of Lithium-Ion batteries.Chem Eng J2021;421:129964