Human economic activity must be decarbonized within several decades to avoid dangerous levels of global warming, with the US passenger fleet a major source of CO2. Decarbonization likely requires an ultimate shift to completely electrified transportation, but given the current reliance of electricity generation on fossil fuels, the optimal deployment schedule of low-carbon vehicles is not known. A simple model is developed for the turnover of the vehicle fleet from the current conventional to an all battery-electric vehicle fleet, including the lifecycle emissions for vehicle production, fuel, and electricity generation. Hybrid-electric vehicles are included as a transitional technology. This model represents the US fleet and both the present and future electrical grid at the county scale, and a range of imposed vehicle market share transition scenarios are considered. To limit cumulative vehicle emissions over the 2017 to 2070 interval, an early, rapid adoption of low-carbon vehicles, either as hybrid or pure electric vehicles, must take place, with an ultimate transition to the battery-electric technology. However, hybrids are found to be an effective transitional technology, and even preferable over the short-term in many areas. Furthermore, some degree of behavioral change, in the form of reduced vehicle miles, must accompany this transition to fully meet climate targets.
The increasing global demand for energy, the need to reduce green house gasses, and the depletion of fossil fuel resources have led for the need for renewable fuel sources such as biodiesel fuels. In the diesel engines, biodiesel fuels can also be used directly without comprehensive engine changes. Biodiesel relates to a diesel fuel that is based on vegetable oil or animal fat consisting of long- chain of methyl, ethyl, or propyl esters. Methyl ester fuel burns more efficiently and has lower emissions of particulate matter, unburnt hydrocarbon, and carbon monoxide than fossil fuels. However, combustion of methyl ester fuel results in increased nitrogen oxides (NOx) emissions relative to fossil fuels. This study is concerned with characterizing the formation of NOx in the combustion of methyl formate under a counter diffusion flame. This was carried out in an Exhaust Gas Recirculation (EGR) system. Simulation of the process was done using Combustion Simulation Laboratory Software (COSILAB), and involved simulating the reactions of methyl formate fuel. The results obtained were compared to those of the methane/air diffusion flame, which is a well-characterized system. The extension validated the results obtained for the methyl formate/air diffusion flame. The reduction of NOx was found to be 26% and 14% in methane and methyl formate diffusion flame respectively from 0% to 29.5% of EGR. Increased EGR from 0% to 29.5% increased NOx reduction. Compared to methane/air diffusion flame, methyl formate/air diffusion flame with and without EGR had lower NOx emission. This was found to be true when examining the amount of other metrics viz. temperature, H, OH and N radicals associated with NOx. This showed that EGR system have an effect on NOx formation.
This paper deals with the stochastic analysis of wind speed based on relative humidity data. We propose a stochastic regression technique to estimate the time-varying parameters of wind speed in a semi-arid climate region. The modeling of stochastic parameters of atmospheric data with consistent properties facilitates prediction with higher precision. In order to compare the estimation, we used simulated atmospheric time series and observational time series. The atmospheric time series was generated by the Weather Research and Forecasting (WRF) model, whereas the observational time series was obtained from the surface weather stations. The time-varying parameters of the model used are estimated by Maximum Likelihood process. The results obtained suggest that relative humidity exhibits a stochastic effect to predict stationary wind speed data. This type of analysis helps to characterize some key meteorological variables, which would be useful in forecasting irregular wind speed.
Within the last decade the production of plastic steadily increased and so did the amount of plastic waste. When bigger plastic pieces enter the environment, they are fragmented over time due to mechanical and environmental forces. The occurring and the directly released microplastic cause severe problems on soil organisms, due to alteration of physical properties and chemical interactions in the habitat. Main emissions sources of microplastic are different kinds of abrasions (road traffic, packaging, fibers of textiles during washing), waste disposal and drifts. Remains of mulching foils and protection nets spoil agricultural soil as well as the application of compost, sewage sludge and digestate, which may contain microplastic. Once released, microplastic accumulates much stronger in terrestrial than in aquatic systems. Spectroscopic, microscopic and thermo-analytical methods are commonly used to analyze microplastic in soil. The main challenges are to differentiate between soil matrix and plastic particles and to get rid of disturbing organic compounds. Unfortunately, there is no soil without plastic, no environmental blind sample to allow the finding of method limits. Inter-laboratory cooperation and data collection should allow estimation and comparison of emissions not only on European but on global scale. Investigations of Austrian samples provided a first orientation for regulations and measures to avoid further environmental pollution.
The environmental impact of buildings has stimulated efforts to promote sustainable development in the construction sector. Technological development aims to provide an effective framework for the design, construction, and management of buildings through the use of tools such as Building Information Modeling (BIM). This paper critically assesses the use of BIM technology in vernacular design and analysis through the case study of a Greek vernacular museum building. Based on software application as well as in-situ observation and interviews, accurate energy analysis and safety were proved to be important advantages achieved through BIM technology. On the contrary, the inability to capture tacit knowledge and the lack of adaptability to local specificities appear to be the main weaknesses of BIM technology. Certain measures to enhance the use of BIM technology for the design and analysis of vernacular buildings are proposed.
In industrialized countries, there is a growing concern about the possible negative effects on human health induced by high levels of heavy metals in soil. It is recognized that high levels of heavy metals are not necessarily indicative of the adverse effects. These effects are related to bioavailable fractions, which are involved in plant uptake and transfer to the food chain. Bioavailability is a complex issue that is essential to evaluate to determine if heavy metals present in soil may pose hazards to humans and the environment. In the case of direct ingestion of soil, it is essential to consider also bioaccessibility. Bioavailability and bioaccessibility are related to several soil processes and may be largely determined by soil characteristics. This review deals with the influence of soil properties on metal bioavailability and bioaccessibility. A case study on bioavailability and bioaccessibility of heavy metals is reported, considering a large uncontaminated area influenced by deposition from a cement plant.