Temperature-independent torsion sensor based on “figure-of-eight” fiber loop mirror

Abstract

An interrogation sensor system combining the “figure-of-eight” fiber loop mirror using a single directional 3×3 fiber optic coupler was proposed. One fiber loop mirror was formed by inserting a length of high birefringent optical fiber at the input ports of the 3×3 coupler. Splicing the output ports of the 3×3 coupler between them created the other fiber loop mirror. The introduction of this second loop gave rise to two polarization states of light with the same frequency but different optical phase. The mechanical torsion sensing head was located at the second loop and was exhibited an average modulus torsion sensitivity of 7.9×10⁻⁴ degree/dB. The performance of the sensor was not affected by environmental temperature variations.

Keywords

Torsion sensor / fiber loop mirror / interferometer

References

[1] Mortimore D. B.. Fiber loop reflectors. Journal Lightwave Technology, 1988, 6(7): 1217-1224.

[2] DelaRosa E., Zenteno L. A., Starodumov A. N., Monzon D.. All-fiber absolute temperature sensor using an unbalanced high-birefringence Sagnac loop. Optics Letters, 1997, 22(7): 481-483.

[3] Starodumov A. N., Zenteno L. A., Monzon D., DeLaRosa E.. Fiber Sagnac interferometer temperature sensor. Applied Physics Letters, 1997, 70(1): 19-21.

[4] Frazao O., Silva R. M., Santos J. L.. High-birefringent fiber loop mirror sensors with an output port probe. IEEE Photonic Technology Letters, 2011, 23(2): 103-105.

[5] Sheem S. K.. Fiber-optic gyroscope with [3×3] directional coupler. Applied Physics Letters, 1980, 37(10): 869-871.

[6] Sheem S. K.. Optical fiber interferometers with [3×3] directional-couplers-analysis. Journal of Applied Physics, 1981, 52(6): 3865-3872.

[7] Priest R. G.. Analysis of fiber interferometer utilizing 3×3 fiber coupler. IEEE Journal of Quantum Electronics, 1982, 18(10): 1601-1603.

[8] Johnson G. A., Todd M. D., Althouse B. L., Chang C. C.. Fiber Bragg grating interrogation and multiplexing with a 3×3 coupler and a scanning filter. Journal Lightwave Technology, 2000, 18(8): 1101-1105.

[9] Cheng L. K., Koops R., Wielders A., Ubachs W.. Development of a fringe sensor based on 3×3 fiber optic coupler for space interferometry. Proc. SPIE, 2005, 5855, 1004-1007.

[10] Liu T. T., Cui J., Chen D. S., Xiao L., Sun D. X.. A new demodulation technique for optical fiber interferometric sensors with [3×3] directional couplers. Chinese Optics Letters, 2008, 6(1): 12-15.

[11] Lo Y. L., Chue B. R., Xu S. H.. Fiber torsion sensor demodulated by a high-birefringence fiber Bragg grating. Optics Communication, 2004, 230(4–6): 287-295.

[12] Jiang Y.. Wavelength division multiplexing addressed four-element fiber optical laser hydrophone array. Applied Optics, 2007, 46(15): 2939-2948.

[13] Frazao O., Silva S. O., Baptista J. M., Santos J. L., Statkiewicz-Barabach G., Urbanczyk W., . Simultaneous measurement of multiparameters using a Sagnac interferometer with polarization maintaining side-hole fiber. Applied Optics, 2008, 47(27): 4841-4848.

[14] Mao Y., Sherif S., Flueraru C., Chang S.. 3×3 Mach-Zehnder interferometer with unbalanced differential detection for full-range swept-source optical coherence tomography. Applied Optics, 2008, 47(12): 2004-2010.

[15] Frazao O., Baptista J. M., Santos J. L.. Recent advances in high-birefringence fiber loop mirror sensors. Sensors, 2007, 7(11): 2970-2983.

[16] Frazao O., Silva R. M., Kobelke J., Schuster K.. Temperature- and strain-independent torsion sensor using a fiber loop mirror based on suspended twin-core fiber. Optics Letters, 2010, 35(16): 2777-2779.