Effect of Solutionizing and Aging on Microstructure and Mechanical Properties of Warm-rolled 7075 Alloy

Abstract

The effect of solution and aging treatments on microstructure and mechanical properties of warm-rolled 7075 alloy was investigated via optical microscope, electron backscattered diffraction, transmission electron microscopy and tensile tests. The 7075 alloy was subjected to solution treatments at 450 °C for 1 h (ST1), 490 °C for 1 h (ST2) and 1.5 h (ST3). Three aging routes were carried out on samples from ST2: one-step (A1), two-step (A2), and three-step aging (A3). The experimental results show mainly recrystallized equiaxed grains in ST1 and ST3 state but a combination of elongated and equiaxed grains in ST2 condition. Three aged alloys have similar microstructures of sample ST2 while the recrystallization frequency gets decreased after aging. The least recrystallization fraction occurs in A2 state. Three aged 7075 alloys all possess enhanced strength and plasticity. Precipitates characterization reveals the maximum strength is achieved in A2 sample as the matrix precipitates are composed mainly of small η and many η′ phases. Aging route A2 appears preferable to other two aging conditions for attaining a pretty excellent combination of strength and plasticity.

Keywords

7075 alloy / solutionizing / aging / precipitate / microstructure / mechanical property

References

[1] Johanne A, Matheus AT, Florian G, et al. Warm-forming of Pre-aged Al−Zn−Mg−Cu Alloy Sheet[J]. Materials and Design, 2020, 193: 1-14.

[2] Lee Y, Koh D, Kim H, et al. Improved Bake-hardening Response of Al−Zn−Mg−Cu Alloy through Pre-ageing Treatment[J]. Scr. Mater., 2018, 147: 45-49.

[3] Couturier L, Deschamps A, Geuser FD, et al. An Investigation of the Strain Dependence of Dynamic Precipitation in an Al−Zn−Mg−Cu Alloy[J]. Scr. Mater., 2017, 136: 120-123.

[4] Mei L, Chen XP, Ren P, et al. Effect of Warm Deformation on Precipitation and Mechanical Properties of a Cryorolled Al−Zn−Mg−Cu Sheet[J]. Mater. Sci. Eng., A., 2020, 771(1): 1-6.

[5] Ivanoff TA, Carter JT, Hector LG, et al. Retrogression and Reaging Applied to Warm Forming of High-strength Aluminum Alloy AA7075-T6 Sheet[J]. Metall. Mater. Trans. A, 2019, 50(3): 1 545-1 561.

[6] Huo WT, Hou LG, Zhang YS, et al. Warm Formability and Post-forming Microstructure/Property of High-strength AA 7075-T6 Al Alloy[J]. Mater. Sci. Eng. A, 2016, 675: 44-54.

[7] Cao YH, He LZ, Zhang L, et al. Effects of Magnetic Field and Hot Rolling on Microstructures and Properties of CryoECAPed 1050 Aluminum Alloy during Annealing[J]. Trans. Nonferrous Metals Soc. China, 2016, 26: 620-626.

[8] Rajamuthamilselvan M, Ramanathan S. Hot Deformation Behaviour of 7075 Alloy[J]. Journal of Alloys and Compounds, 2011, 509: 948-952.

[9] Tanaka H, Minoda T. Mechanical Properties of 7 475 Aluminum Alloy Sheets with Fine Subgrain Structure by Warm Rolling[J]. Trans. Nonferrous Met. Soc. China, 2014, 24: 2 187-2 195.

[10] Mei L, Chen XP, Huang GJ, et al. Improvement of Mechanical Properties of a Cryorolled Al−Mg−Si Alloy through Warm Rolling and Aging[J]. J. Alloy. Comp., 2019, 777: 259-263.

[11] Jiang JF, Liu YZ, Xiao GF, et al. Effect of Pass Reduction on Microstructure, Mechanical Properties and Ttexture of Hot-rolled 7075 Alloy[J]. Materials Characterization, 2019, 147: 324-339.

[12] Mondal C, Singh AK, Mukhopadhyay AK, et al. Tensile Flow and Work Hardening Behavior of Hot Cross-rolled AA7010 Aluminum Alloy Sheets[J]. Mater. Sci. Eng. A, 2013, 577: 87-100.

[13] Rader K, Iyanoff T, Shin H, et al. Determining a Retrogression Heat Treatment to Apply during Warm Forming of a High Strength Aluminum AA7075 Sheet Material[J]. Light Metals, 2018: 241–246

[14] Zhang YD, Jin SB, Patrick WT, et al. Dynamic Precipitation, Ssegregation and Strengthening of an Al−Zn−Mg−Cu Alloy (AA7075) Processed by High-pressure Torsion[J]. Acta Mater., 2019, 162: 19-32.

[15] Huo WT, Hou LG, Cui H, et al. Fine-grained AA7075 Processed by Different Thermomechanical Processings[J]. Materials Science & Engineering A, 2014, 618: 244-253.

[16] Chen ZG, Yuan ZG, Ren JK. The Mechanism of Comprehensive Properties Enhancement in Al−Zn−Mg−Cu Alloy via Novel Thermomechanical Ttreatment[J]. Journal of Alloys and Compounds, 2020, 828: 1-10.

[17] Wert JA, Paton NE, Hamilton CH, et al. Grain Refinement in 7075 Aluminium by Thermo-mechanical Processing[J]. Metall. Trans., A, 1981, 12: 1 267-1 276.

[18] Paton NE, Hamilton CH, Wert JA, et al. Characterization of Fine-Grained Superplastic Aluminum Alloys[J]. J. Met., 1982, 34(8): 21-27.

[19] Jiang XG, Cui JZ, Ma LX. The influence of the Rolling Direction on the Mechanical Behavior and Cavity Formation during Superplastic Deformation of 7075 A1 Alloy[J]. Acta Metall., 1993, 41(9): 2 721-2 727.

[20] Shaeri MH, Salehi MT, Seyyedein SH, et al. Microstructure and Mechanical Properties of Al-7075 Alloy Processed by Equal Channel Angular Pressing Combined with Aging Treatment[J]. Materials and Design, 2014, 57: 250-257.

[21] Liu CH, Li XL, Wang SH, et al. A Tuning Nanoprecipitation Approach for Achieving Enhanced Strength and Good Ductility in Al Alloys[J]. Mater. Des., 2014, 54: 144-148.

[22] Wang ZX, Li H, Miao FF, et al. Improving the Strength and Ductility of Al−Mg−Si−Cu Alloys by a Novel Thermo-mechanical Treatment[J]. Mater. Sci. Eng., 2014, 607: 313-317.

[23] Birbilis N, Cavanangh MK, Buchheit RG. Electrochemical Behavior and Localized Corrosion Associated with Al7Cu2Fe Particles in Aluminum alloy 7075-T651[J]. Corros. Sci., 2006, 48(12): 4 202-4 215.

[24] Sushanta KP, Jayaganthan R. Development of Ultrafine Grained High Strength Age Hardenable Al 7075 Alloy by Cryorolling[J]. Mater.Des., 2011, 32(6): 3 150-3 160.

[25] Huo WT, Sun TT, Hou LG, et al. Effect of Heating Rate during Solution Treatment on Microstructure, Mechanical Property and Corrosion Resistance of High-strength AA 7075 Alloy[J]. Materials Characterization, 2020, 167: 1-9.

[26] Jiang JF, Wang Y, Xiao GF, et al. Comparison of Microstructural Evolution of 7075 Aluminum Alloy Fabricated by SIMA and RAP[J]. J. Mater. Process. Technol., 2016, 238: 361-372.

[27] Atkinson HV, Burke K, Vaneetveld G. Recrystallisation in the Semi-solid State in 7075 Aluminium Alloy[J]. Mater. Sci. Eng. A, 2008, 25: 266-276.

[28] Li H, Chen P, Wang ZX, et al. Tensile Properties, Microstructures and Fracture Behaviors of an Al−Zn−Mg−Cu Alloy during Ageing after Solution Treating and Cold-rolling[J]. Mater. Sci. Eng. A, 2019, 742: 798-812.

[29] Peng GS, Chen KH, Chen S, et al. Influence of Repetitious-RRA Ttreatment on the Strength and SCC Resistance of Al−Zn−Mg−Cu Alloy[J]. Materials Science and Engineering A, 2011, 528(12): 4 014-4 018.

[30] Mohamed AA, Ying CW, Terence GL. Effect of Dynamic Plastic Deformation on the Microstructure and Mechanical Properties of an Al−Zn−Mg Alloy[J]. Materials Science & Engineering A, 2020, 784: 1-10.

[31] Li HT, Nancy JS, Bih LC, et al. Microstructure Transition and Grain Refinement Mechanism of Undercooled Alloys[J]. Journal of Wuhan University of Technology -Materials Science Edition, 2021, 36(6): 922-926.