Selective Laser Melting of Commercially Pure Silicon

Abstract

Selective laser melting (SLM) or Laser-based powder bed fusion (LBPF) is gaining much attention for the fabrication of novel materials with complex shapes, improved functionalities, and properties. An attempt has been made to fabricate hard and brittle silicon via SLM in the absence of any cracks. Two different powder batches were used, where one of the powder batches has 0.3wt% Fe and the other batch with 0.02wt% Fe. The parameter optimization process shows that the SLM Si samples were successfully fabricated from the powders with the minor addition of Fe. The deliberate addition of Fe facilitates heterogeneous nucleation of Si and aids in absorbing the laser energy beam more efficiently. SLM Si samples with 98.5% theoretical density were fabricated with a hardness of around 10.65±40 GPa. The experimental results show that SLM can successfully fabricate Si without cracks and with near theoretical density (of 99%) and complex shapes, which opens their use in wider industrial applications.

Keywords

additive manufacturing / selective laser melting / silicon / heterogeneous nucleation

References

[1] Jaroniec M. Silicon Beyond the Valley[J]. Nature Chemistry, 2009, 1(2): 166-166.

[2] Marrows CH. Silicon Goes Heavyweight[J]. Nature Materials, 2021, 20(9): 1 177-1 178.

[3] Konoplyannikov MA, Eremina AS, Kargina YV, et al. Mesoporous Silicon Nanoparticles Loaded with Salinomycin for Cancer Therapy Applications[J]. Microporous and Mesoporous Material, 2021, 328: 111 473.

[4] Zou J, Sun F, Wang C, et al. Silicon-based Arrayed Waveguide Gratings for WDM and Spectroscopic Analysis Applications[J]. Optics & Laser Technology, 2022, 147: 107 656.

[5] Dourado DM, de Farias GB, Gounella RH, et al. Challenges in Silicon Photonics Modulators for Data Center Interconnect Applications[J]. Optics & Laser Technology, 2021, 144: 107 376.

[6] Chaluvadi SK, Wang Z, Carvalho de Araújo LM, et al. Integration of Epitaxial La2/3Sr1/3MnO3 Thin Films on Silicon-on-Sapphire Substrate for MEMS Applications[J]. Applied Surface Science, 2022, 579: 152 095.

[7] He Y, Vasconcellos DS, Bourrier D, et al. Lateral Porous Silicon Interferometric Transducer for On-chip Flow-through Sensing Applications[J]. Sensors and Actuators A: Physical M, 2021, 332: 113 089.

[8] Cui Y. Silicon Anodes[J]. Nature Energy, 2021, 6(10): 995-996.

[9] Jalili R, Esrafilzadeh D, Aboutalebi SH, et al. Silicon as a Ubiquitous Contaminant in Graphene Derivatives with Significant Impact on Device Performance[J]. Nature Communications, 2018, 9(1): 1-13.

[10] Amanov A. Improvement in Surface Properties of Si Wafer by Mechanical Surface Treatment[J]. Journal of Physics and Chemistry of Solids, 2020, 138: 109 272.

[11] Marks MR, Cheong KY, Hassan Z. A Review of Laser Ablation and Dicing of Si Wafers[J]. Precision Engineering, 2022, 73: 377-408.

[12] He Y, Ma W, Xing A, et al. A Review of the Process on the Purification of Metallurgical Grade Silicon by Solvent Refining[J]. Materials Science in Semiconductor Processing, 2022, 41: 106 438.

[13] Akhtar SS. A Critical Review on Self-lubricating Ceramic-composite Cutting Tools[J]. Ceramics International, 2021, 74: 20 745-20 767.

[14] Fischer AC, Belova LM, Rikers YGM, et al. 3D Free-Form Patterning of Silicon by Ion Implantation, Silicon Deposition, and Selective Silicon Etching[J]. Advanced Functional Materials, 2012, 22: 4 004-4 008.

[15] Crone WC, Sharpe WN. Springer Handbook of Experimental Solid Mechanics[M], 2008 New York: Springer.

[16] Fan X, Smith AD, Forsberg F, et al. Manufacture and Characterization of Graphene Membranes with Suspended Silicon Proof Masses for MEMS and NEMS Applications[J]. Microsystems & Nanoengineering, 2020, 6(1): 1-17.

[17] Eyers DR, Potter AT. Industrial Additive Manufacturing: a Manufacturing Systems Perspective[J]. Computers in Industry, 2017, 92: 208-218.

[18] Paul CP, Jinoop AN, Bindra KS. Metal Additive Manufacturing Using Lasers[M], 2015 Florida: CRC Press.

[19] Gokuldoss PK, Kolla S, Eckert J. Additive Manufacturing Processes: Selective Laser Melting, Electron Beam Melting and Binder Jetting-Selection Guidelines[J]. Materials, 2017, 10: 1-11.

[20] Brandt M. Laser Additive Manufacturing: Materials, Design, Technologies, and Applications[M], 2016 Londn: Woodhead Publishing.

[21] Prashanth KG, Wang Z. Additive Manufacturing: Alloy Design and Process Innovations[J]. Materials, 2020, 13: 542.

[22] Velasco-Hogan A, Xu J, Meyers MA. Additive Manufacturing as a Method to Design and Optimize Bioinspired Structures[J]. Advanced Materials, 2018, 30(52): 180 094 0

[23] Ahn DG. Directed Energy Deposition (DED) Process: State of the Art[J]. International Journal of Precision Engineering and Manufacturing-Green Technology, 2021, 8(2): 703-742.

[24] Liu M, Kumar A, Bukkapatnam S, Kuttolamadom M. A Review of the Anomalies in Directed Energy Deposition (DED) Processes & Potential Solutions — Part Quality & Defects[J]. Procedia Manufacturing, 2021, 53: 507-518.

[25] Singh A, Kapil S, Das M. A Comprehensive Review of the Methods and Mechanisms for Powder Feedstock Handling in Directed Energy Deposition[J]. Additive Manufacturing, 2020, 35: 101 388.

[26] Dantec ML, Abdulstaar M, Leparoux M, et al. Epitaxial Growth of Silicon on Silicon Wafers by Direct Laser Melting[J]. Materials, 2020, 13: 4 728.

[27] Minasyan T, Liu L, Aghayan M, et al. A Novel Approach to Fabricate Si3N4 by Selective Laser Melting[J]. Ceramics International, 2018, 44: 13 689-13 694.

[28] Fruggiero F, Lambiase A, Bonito R, et al. The Load of Sustainability for Additive Manufacturing Processes[J]. Procedia Manufacturing, 2019, 41: 375-382.

[29] Santecchia E, Spigarelli S, Cabibbo M. Material Reuse in Laser Powder Bed Fusion: Side Effects of the Laser-Metal Powder Interaction[J]. Metals, 2020, 10: 341.

[30] Cordova L, Campos M, Tinga T. Revealing the Effects of Powder Reuse for Selective Laser Melting by Powder Characterization[J]. JOM, 2019, 71(3): 1 062-1 072.

[31] Prashanth KG, Löber L, Klauss HJ, et al. Characterization of 316L Steel Cellular Dodecahedron Structures Produced by Selective Laser Melting[J]. Technologies (Basel), 2016, 4: 34.

[32] Tilton M, Lewis GS, Bok Wee H, et al. Additive Manufacturing of Fracture Fixation Implants: Design, Material Characterization, Biomechanical Modeling and Experimentation[J]. Additive Manufacturing, 2020, 33: 101 137.

[33] Prashanth KG, Shakur Shahabi H, Attar H, et al. Production of High Strength Al₈₅Nd₈Ni₅Co₂ Alloy by Selective Laser Melting[J]. Additive Manufacturing, 2015, 6: 1-5.

[34] Wang Z, Cudino SS, Eckert J, et al. Selective Laser Melting of Nanostructured Al-Y-Ni-Co Alloy[J]. Manufacturing Letters, 2020, 25: 21-25.

[35] Lakhdar Y, Tuck C, Binner J, et al. Additive Manufacturing of Advanced Ceramic Materials[J]. Progress in Materials Science, 2021, 116: 100 736.

[36] Martin JH, Yahata BD, Hundley JM, et al. 3D Printing of High-strength Aluminium Alloys[J]. Nature, 2017, 549: 365-369.

[37] Tsoutsouva MG, Stokkan G, Regula G, et al. Random Angle Grain Boundary Formation and Evolution Dynamics during Si Directional Solidification[J]. Acta Materialia, 2019, 171: 253-260.

[38] Boyd IW, Binnie TD, Wilson JIB, et al. Absorption of Infrared Radiation in Silicon[J]. Journal of Applied Physics, 1998, 55: 3 061.

[39] Rämer A, Osmani O, Rethfeld B. Laser Damage in Silicon: Energy Absorption, Relaxation, and Transport[J]. Journal of Applied Physics, 2014, 116: 053 508.

[40] Artamonov VV, Bykov AO, Bykov PO, et al. Measurement of the Tap Density of Metal Powders[J]. Powder Metallurgy and Metal Ceramics, 2013, 52: 237-239.

[41] ASTM B213-17 Standard Test Methods for Flow Rate of Metal Powders Using the Hall Flowmeter Funnel[S], 2017 West Lonsho Hocken, PA, USA: ASTM International.

[42] Mellin P, Lyckfeldt O, Harlin P, et al. Evaluating Flowability of Additive Manufacturing Powders, using the Gustavsson Flow Meter[J]. Metal Powder Report, 2017, 72: 322-326.

[43] Spierings AB, Voegtlin M, Bauer T, et al. Powder Flowability Characterisation Methodology for Powder-Bed-Based Metal Additive Manufacturing[J]. Progress in Additive Manufacturing, 2016, 1: 9-20.

[44] Oliver WC, Pharr GM. Measurement of Hardness and Elastic Modulus by Instrumented Indentation: Advances in Understanding and Refinements to Methodology[J]. Journal of Materials Research, 2004, 19: 3-20.

[45] Maity T, Prashanth KG, Balci, et al. Influence of Severe Straining and Strain Rate on the Evolution of Dislocation Structures during Micro-/Nanoindentation in High Entropy Lamellar Eutectics[J]. International Journal of Plasticity, 2018, 109: 121-136.

[46] Lin D, Lu Z, Hsu PC, et al. A High Tap Density Secondary Silicon Particle Anode Fabricated by Scalable Mechanical Pressing for Lithium-Ion Batteries[J]. Energy & Environmental Science, 2015, 8: 2 371-2 376.

[47] Yu AB, Hall JS. Packing of Fine Powders Subjected to Tapping[J]. Powder Technology, 1994, 78: 247-256.

[48] Santomaso A, Lazzaro P, Canu P. Powder Flowability and Density Ratios: The Impact of Granules Packing[J]. Chemical Engineering Science, 2003, 58: 2 857-2 874.

[49] Vlachos N, Chang ITH. Investigation of Flow Properties of Metal Powders From Narrow Particle Size Distribution to Polydisperse Mixtures through an Improved Hall-Flowmeter[J]. Powder Technology, 2011, 205: 71-80.

[50] Prashanth KG, Scudino S, Maity T, et al. Is the Energy Density a Reliable Parameter for Materials Synthesis By Selective Laser Melting[J]. Materials Research Letters, 2017, 5: 386-390.

[51] Scipioni Bertoli U, Wolfer AJ, Matthews MJ, et al. On the Limitations of Volumetric Energy Density as a Design Parameter for Selective Laser Melting[J]. Materials and Design, 2017, 113: 331-340.

[52] Ghayoor M, Lee K, He Y, et al. Selective Laser Melting of 304L Stainless Steel: Role of Volumetric Energy Density on the Microstructure, Texture and Mechanical Properties[J]. Additive Manufacturing, 2020, 32: 101 011.

[53] Louvis E, Fox P, Sutcliffe CJ. Selective Laser Melting of Aluminium Components[J]. Journal of Materials Processing Technology, 2011, 211: 275-284.

[54] Löber L, Schimansky FP, Kühn U, et al. Selective Laser Melting of a Beta-Solidifying TNM-B1 Titanium Aluminide Alloy[J]. Journal of Materials Processing Technology, 2014, 214: 1 852-1 860.

[55] Gusarov AV, Yadroitsev I, Bertrand P, et al. Heat Transfer Modelling and Stability Analysis of Selective Laser Melting[J]. Applied Surface Science, 2007, 254: 975-979.

[56] Kumar S. Selective Laser Sintering/Melting[J]. Comprehensive Materials Processing, 2014(10): 93–134

[57] Li L, Anand S. Hatch Pattern Optimization of Powder Bed Fusion Additive Manufacturing Process for Minimizing Flatness Error[J]. Procedia Manufacturing, 2021, 53: 456-465.

[58] Al-Maharma AY, Patil SP, Markert B. Effects of Porosity on the Mechanical Properties of Additively Manufactured Components: A Critical Review[J]. Materials Research Express, 2020, 7: 122 001.

[59] Aboulkhair NT, Simonelli M, Parry L, et al. 3D Printing of Aluminium Alloys: Additive Manufacturing of Aluminium Alloys Using Selective Laser Melting[J]. Progress in Materials Science, 2019, 106: 100 578.

[60] Prashanth KG, Scudino S, Eckert J. Defining the Tensile Properties of Al-12Si Parts Produced by Selective Laser Melting[J]. Acta Materialia, 2017, 126: 25-35.

[61] Zhou X, Li K, Zhang D, et al. Textures Formed in a Cocrmo Alloy by Selective Laser Melting[J]. Journal of Alloys and Compounds, 2015, 631: 153-164.

[62] Li XP, Humbeeck JV, Kruth JP. Selective Laser Melting of Weak-Textured Commercially Pure Titanium with High Strength and Ductility: A Study from Laser Power Perspective[J]. Materials and Design, 2017, 116: 352-358.

[63] Wei HL, Mazumder J, DebRoy T. Evolution of Solidification Texture During Additive Manufacturing[J]. Scientific Reports, 2015, 5: 1-7.

[64] Kumar D, Shankar G, Prashanth KG, et al. Texture Dependent Strain Hardening in Additively Manufactured Stainless Steel 316L[J]. Materials Science and Engineering A, 2021, 820: 141 483.

[65] Xi L, Wang P, Prashanth KG, et al. Effect of TiB2 Particles on Microstructure and Crystallographic Texture of Al-12Si Fabricated by Selective Laser Melting[J]. Journal of Alloys and Compounds, 2019, 786: 551-556.

[66] Zhao C, Wang Z, Li D, et al. Cu-Ni-Sn Alloy Fabricated by Melt Spinning and Selective Laser Melting: A Comparative Study on the Microstructure and Formation Kinetics[J]. Journal of Materials Research and Technology, 2020, 9: 13 097-13 105.

[67] Zhao C, Wang Z, Li D, et al. Selective Laser Melting Of Cu-Ni-Sn: A Comprehensive Study on the Microstructure, Mechanical Properties, and Deformation Behavior[J]. International Journal of Plasticity, 2021, 138: 102 926.

[68] Wang Z, Xie M, Li Y, et al. Premature Failure of an Additively Manufactured Material[J]. NPG Asia Materials, 2020, 12: 1-10.

[69] Wang G, Ouyang H, Fan C, et al. The Origin of High-Density Dislocations in Additively Manufactured Metals[J]. Materials Research Letters, 2020, 8: 283-290.

[70] Jung HY, Choi SJ, Prashanth KG, et al. Fabrication of Fe-based Bulk Metallic Glass by Selective Laser Melting: a Parameter Study[J]. Materials and Design, 2015, 86: 703-708.

[71] DebRoy T, Wei HL, Zuback JS, et al. Additive Manufacturing of Metallic Components-Process, Structure and Properties[J]. Progress in Materials Science, 2018, 92: 112-224.

[72] Zhou L, Gao F, Peng GS, et al. Effect of Potent TiB₂ Addition Levels and Impurities on the Grain Refinement of Al[J]. Journal of Alloys and Compounds, 2016, 689: 401-407.

[73] Mohanty PS, Gruzleski JE. Mechanism of Grain Refinement in Aluminium[J]. Acta Metallurgica et Materialia, 1995, 43: 2 001-2 012.

[74] Mair P, Kaserer L, Braun J, et al. Microstructure and Mechanical Properties of a TiB₂-modified Al-Cu Alloy Processed by Laser Powder-bed Fusion[J]. Materials Science and Engineering: A, 2021, 799: 140 209.

[75] Antonio JAM, Lfo LFM. Grain Refinement in Aluminum Alloyed with Titanium and Boron[J]. Metallurgical Transactions, 1971, 2(2): 465-471.

[76] Murty BS, Kori SA, Chakraborty M. Grain Refinement of Aluminium and Its Alloys by Heterogeneous Nucleation and Alloying[J]. International Materials Reviews, 2002, 47: 3-29.