Effects of Lay-up Types of Out-of-autoclave Prepregs on Preparation Quality of L-shape Composite Laminates

Abstract

Effects of layer quantities and stacking sequences on L-shape composite manufacturing qualities in using OOA(out-of-autoclave) prepregs were studied. The mechanisms of air evacuated in 5 kinds of lay-ups were revealed by image analysis of cut surfaces and thickness measurements. Results show that air in OOA prepregs is evacuated in two ways. Most of the air is forced out of layers directly by vacuum before air accesses in prepregs closed. Very little entrapped air moves perpendicularly to outer layers under hydrostatic resin pressure. When a laminate contains less than 16 layers, voids can hardly be found in layers. When a laminate contains more than 16 layers, voids cannot be expelled completely during the window of vertical movement. As for stacking sequences, the synergetic effect of slip function and nest function determines the thickness and voids content of laminates. Results show that the average of single layer thickness of unidirectional layers is the lowest, and the average of single layer thickness of quasi-isotropic layers is the highest. The voids content of quasi isotropic is the highest, which is consistent with the theoretical analysis.

Keywords

OOA prepregs / L-shape composite laminates / lay-up type

References

[1] Krumenacker N, Hubert P. Effect of Processing Deficiencies on Vacuum-Bag-Only Complex-Shape Prepreg Laminate Consolidation and Interlaminar Tensile Behaviour[C]. In: Proceedings of 20th International Conference on Composite Materials 2015, Copenhagen, Denmark, 2015

[2] Zhang X, Zhou R, Chen J, et al. Influence of Low-Velocity Impact on Damage Behavior of Carbon Fiber-Reinforced Composites[J]. Journal of Wuhan Unversity of Technology-Materials Science Edtion, 2020, 35(3): 482-487.

[3] Ma Y Centea, T Nilakantan G, Nutt S, et al. Vacuum Bag Only Processing of Complex Shapes: Effect of Corner Angle, Material Properties and Processing Conditions[C]. In: American Society for Composites 29th Technical Conference, La Jolla, CA 2014

[4] Garschke C, Weimer C, Parlevliet P, et al. Out-of-autoclave Cure Cycle Study of a Resin Film Infusion Process Using in Situ Process Monitoring[J]. Composites Part A: Applied Science and Manufacturing, 2012, 43(6): 935-944.

[5] Helmus R, Centea T, Hubert P, et al. Out-of-Autoclave Prepreg Consolidation: Coupled Air Evacuation and Prepreg Impregnation Modeling[J]. Journal of Composite Materials, 2016, 50(10): 1403-1413.

[6] Centea T, Hubert P. The Effect of Material and Process Parameters on Tow Impregnation and Micro-void Formation in Out-of-autoclave Prepregs[J]. ASC Series on Advances in Composite Materials: Vol. 6, Manufacturing of Composites, 2013, 6: 255.

[7] Centea T, Grunenfelder LK, Nutt SR, et al. A Review of Out-of-Autoclave Prepregs-Material Properties, Process Phenomena, and Manufacturing Considerations[J]. Composites Part A: Applied Science and Manufacturing, 2015, 70: 132-154.

[8] Kourkoutsaki T, Comas-Cardona S, Binetruy C, et al. The Impact of Air Evacuation on the Impregnation Time of Out-of-Autoclave Prepregs[J]. Composites Part A: Applied Science and Manufacturing, 2015, 79: 30-42.

[9] Levy A, Stadlin J, Hubert P, et al. Corner Consolidation in Vacuum Bag Only Processing of Out-of-Autoclave Composite Prepregs Laminates[C]. In: SAMPE 2014 Technical Conference, Seattle 2014

[10] Hughes SM, Hubert P. Out-of-Autoclave Prepreg Processing: Effect of Integrated Geometric Features on Part Quality[C]. SAMPE Tech 2013, Wichita 2013

[11] Cauberghs J. Out-of-Autoclave Manufacturing of Aerospace Representative Parts[D], 2012 Canada: McGill University.

[12] Centea T, Hubert P. Out-of-Autoclave Prepreg Consolidation under Deficient Pressure Conditions[J]. Journal of Composite Materials, 2014, 48(16): 2033-2045.

[13] Li Y, Li M, Gu Y, et al. Numerical and Experimental Study on the Effect of Lay-up Type and Structural Elements on Thickness Uniformity of L-Shaped Laminates[J]. Applied Composite Materials, 2009, 16(2): 101-115.

[14] Brillant M, Hubert P. Out-of-Autoclave Processing of Complex Shape Laminates[C]. In: 54th International SAMPE Symposium and Exhibition 2010, 2010

[15] Cauberghs J, Hubert P. Effect of Tight Corners and Ply Terminations on Quality in Out-of-Autoclave Parts[C]. In: Proceedings of the SAMPE 2011 Conference of the Society for the Advancement of Materials and Process Engineering 2011, 2011

[16] Hubert P, Poursartip A. Aspects of the Compaction of Composite Angle Laminates: An Experimental Investigation[J]. Journal of Composite Materials, 2001, 35(1): 2-26.

[17] Sorrentino L, Bellini C. Potentiality of Hot Drape Forming to Produce Complex Shape Parts in Composite Material[J]. The International Journal of Advanced Manufacturing Technology, 2016, 85(5–8): 945-954.

[18] Wysocki M, Larsson R, Toll S, et al. Modelling the Consolidation of Partially Impregnated Prepregs[C]. In: 17th International Conference on Composite Materials, Edinburgh, Scotland, 2009

[19] Centea T, Hubert P. Measuring the Impregnation of an Out-of-Autoclave Prepreg by Micro-CT[J]. Composites Science and Technology, 2011, 71(5): 593-599.

[20] O’Neill S, Kilic MH. Discontinuous Long-Fiber (DLF) Thermoplastic Composite Replacement for Complex-Shape Metallic Helicopter Fairing Rib[J]. SAMPE. J., 2016, 52(5): 28-35.

[21] Shi H, Fernandez Villegas, I Bersee, et al. A Study of Process Induced Voids in Resistance Welding of Thermoplastic Composites[C]. In: ICCM 20: 20th International Conference on Composite Materials, Copenhagen, Denmark, 2015

[22] Liu L, Zhang B-M, Wang D-F, et al. Effects of Cure Cycles on Void Content and Mechanical Properties of Composite Laminates[J]. Composite Structures, 2006, 73(3): 303-309.

[23] Grunenfelder L, Nutt S. Void Formation in Composite Prepregs-Effect of Dissolved Moisture[J]. Composites Science and Technology, 2010, 70(16): 2304-2309.

[24] Dave R, Kardos J, Duduković M, et al. A Model for Resin Flow During Composite Processing Part 2: Numerical Analysis for Unidirectional Graphite/Epoxy Laminates[J]. Polymer Composites, 1987, 8(2): 123-132.

[25] Kardos, J, Duduković M, Dave R et al. Void Growth and Resin Transport During Processing of Thermosetting—Matrix Composites[C]. In: Epoxy Resins and Composites IV, Springer, 1986

[26] Thomas S, Bongiovanni C, Nut S, et al. In Situ Estimation of Through-Thickness Resin Flow Using Ultrasound[J]. Composites Science and Technology, 2008, 68(15): 3093-3098.

[27] Guo Z-S, Liu L, Zhang B-M, et al. Critical Void Content for Thermoset Composite Laminates[J]. Journal of Composite Materials, 2009, 43(17): 1775-1790.

[28] Alshahrani H, Hojjati M. A Theoretical Model with Experimental Verification for Bending Stiffness of Thermosetting Prepreg During Forming Process[J]. Composite Structures, 2017, 166: 136-145.

[29] Kratz J, Hsiao K, Fernlund G, et al. Thermal Models for MTM45-1 and Cycom 5320 Out-of-Autoclave Prepreg Resins[J]. Journal of Composite Materials, 2013, 47(3): 341-352.

[30] Vora KUR. Mechanical Properties Evolution During Cure for Out-of-autoclave Carbon-Epoxy Prepregs[D], 2012 Wichita: Wichita State University.