Effect of Curing Temperature on Tunnel Fire Insulation of Aerogel Cement Paste Coatings

Abstract

To further strengthen the protective effect of aerogel cement paste (ACP) coating on self-compacting concrete (SCC) in tunnel fire under the optimal mix proportion, the effect of curing temperature (from 5 to 80 °C, based on site construction curing temperature and surrounding rock temperature) on fire insulation of ACP was investigated. The mechanical properties, thermal conductivity and porosity of ACP were tested. The microstructure of ACP was characterized by means of SEM, XRD and TG/DTG. The results reveal that 50 °C is the optimal curing temperature for ACP with good mechanical properties and fire insulation. Relatively high curing temperature can facilitate hydration and pozzolanic reactions, contributing to the generation of more stable substances (such as C-S-H gels, tobermorite and thenardite, etc). ACP under excessive low curing temperature brings inhomogeneous microstructure with coarse pores, leading to producing wider and longer microcracks when it is exposed to tunnel fire. The microcracks make the heat convection and thermal radiation more significant and thus accelerate the damage of ACP under fire. In case of the less than 7% difference of thermal conductivity, dense microstructure and stable substances are more conducive to strengthening fire insulation of ACP. In practical engineering applications, the thickness of protective layer of ACP can be further optimized when ACP is cured under about 50 °C.

Keywords

aerogel cement paste / curing temperature / tunnel fire insulation / microstructure / stable hydration products

References

[1] Broere W. Urban Underground Space: Solving the Problems of Today’s Cities[J]. Tunnelling and Underground Space Technology, 2016, 55: 245-248.

[2] Huang Y, Li Y, Dong B, et al. Numerical Investigation on the Maximum Ceiling Temperature and Longitudinal Decay in a Sealing Tunnel Fire[J]. Tunnelling and Underground Space Technology, 2018, 72: 120-130.

[3] Du S, Zhang Y, Sun Q, et al. Experimental Study on Color Change and Compression Strength of Concrete Tunnel Lining in a Fire[J]. Tunnelling and Underground Space Technology, 2018, 71: 106-114.

[4] He L, Xu Z, Chen H, et al. Analysis of Entrainment Phenomenon Near Mechanical Exhaust Vent and a Prediction Model for Smoke Temperature in Tunnel Fire[J]. Tunnelling and Underground Space Technology, 2018, 80: 143-150.

[5] Ren R, Zhou H, Hu Z, et al. Statistical Analysis of Fire Accidents in Chinese Highway Tunnels 2000–2016[J]. Tunnelling and Underground Space Technology, 2019, 83: 452-460.

[6] Dong X, Ding Y, Wang T. Spalling and Mechanical Properties of Fiber Reinforced High-Performance Concrete Subjected to Fire[J]. Journal of Wuhan University of Technology-Mater. Sci. Ed., 2008, 23(5): 743-749.

[7] Wang Y, Qin T, Sun X, et al. Full-Scale Fire Experiments and Simulation of Tunnel with Vertical Shafts[J]. Applied Thermal Engineering, 2016, 105: 243-255.

[8] Kim J, Mook L, Won J, et al. Fire Resistant Behavior of Newly Developed Bottom-Ash-Based Cementitious Coating Applied Concrete Tunnel Lining under RABT Fire Loading[J]. Construction and Building Materials, 2010, 24(10): 1 984-1 994.

[9] Yasir M, Ahmad F, Megat-yusoff P, et al. Quantifying the Effects of Basalt Fibers on Thermal Degradation and Fire Performance of Epoxy-Based Intumescent Coating for Fire Protection of Steel Sub-strate[J]. Progress in Organic Coatings, 2019, 132: 148-158.

[10] Zhu P, Brunner S, Zhao S, et al. Study of Physical Properties and Microstructure of Aerogel-Cement Mortars for Improving the Fire Safety of High-Performance Concrete Linings in Tunnels[J]. Cecment and Concrete Composites, 2019, 104: 103 414.

[11] Zhu P, Xu X, Liu H, et al. Tunnel Fire Resistance of Self-Compacting Concrete Coated with SiO₂ Aerogel Cement Paste under 2.5 h HC Fire Loading[J]. Construction and Building Materials, 2020, 239: 117 857.

[12] Zhu P, Jia Z, Wang X, et al. Density Dependence of Tunnel Fire Resistance for Aerogel-Cement Mortar Coatings[J]. Journal of Wuhan University of Technology-Mater. Sci. Ed., 2020, 155(03): 134-140.

[13] Krishna R, Rupesh K. Comparative Study on the Behaviour of GPC Using Silica Fume and Fly Ash with GGBS Exposed to Elevated Temperature and Ambient Curing Conditions[J]. Materials Today: Proceedings, 2020, 27: 1 833-1 837.

[14] Adam A, Horianto X. The Effect of Temperature and Duration of Curing on the Strength of Fly Ash Based Geopolymer Mortar[J]. Procedia Engineering, 2014, 95: 410-414.

[15] Borštnar M, Daneu N, Dolenec S. Phase Development and Hydration Kinetics of Belite-Calcium Sulfoaluminate Cements at Different Curing Temperatures[J]. Ceramics International, 2020, 46(18): 29 421-29 428. Part B

[16] Zhao H, Xiang Y, Xie D, et al. Effects of CaO-Based and MgO-Based Expansion Agent, Curing Temperature and Restraint Degree on Pore Structure of Early-Age Mortar[J]. Construction and Building Materials, 2020, 257: 119 572.

[17] Wang P, Li N, Xu L. Hydration Evolution and Compressive Strength of Calcium Sulphoaluminate Cement Constantly Cured over the Temperature Range of 0 to 80 °C[J]. Cement and Concrete Research, 2017, 100: 203-213.

[18] Peng G, Niu X, Shang Y, et al. Combined Curing as a Novel Approach to Improve Resistance of Ultra-High Performance Concrete to Explosive Spalling under High Temperature and Its Mechanical Properties[J]. Cement and Concrete Research, 2018, 109: 147-158.

[19] Li T, Huang F, Zhu J, et al. Effect of Foaming Gas and Cement Type on the Thermal Conductivity of Foamed Concrete[J]. Construction and Building Materials, 2020, 231: 117 197.

[20] Niubó M, Formosa J, Maldonado A, et al. Magnesium Phosphate Cement Formulated with Low Grade Magnesium Oxide with Controlled Porosity and Low Thermal Conductivity as a Function of Admixture[J]. Ceramics International, 2016, 42(13): 15 049-15 056.

[21] Wang J, Xu H, Xu D, et al. Accelerated Carbonation of Hardened Cement Pastes: Influence of Porosity[J]. Construction and Building Materials, 2019, 225: 159-169.

[22] Zhang X, Yang J, Li K, et al. Effects of Steam on the Compressive Strength and Microstructure of Cement Paste Cured under Alternating Ultrahigh Temperature[J]. Cement and Concrete Composites, 2020, 112: 103 681.

[23] Habib A, Aiad I, El-hosiny F, et al. Development of the Fire Resistance and Mechanical Characteristics of Silica Fume-Blended Cement Pastes Using Some Chemical Admixtures[J]. Construction and Building Materials, 2018, 181: 163-174.

[24] Ng S, Jelle B, Sandberg L, et al. Experimental Investigations of Aerogel-Incorporated Ultra-High Performance Concrete[J]. Construction and Building Materials, 2015, 77: 307-316.

[25] Leiva C, Vilches L, Vale J, et al. Influence of the Type of Ash on the Fire Resistance Characteristics of Ash-Enriched Mortars[J]. Fuel, 2005, 84(11): 1 433-1 439.

[26] Hu J, Zhao F, Kuang Y, et al. Microscopic Characteristics of the Action of an Air Entraining Agent on Cemented Paste Backfill Pores[J]. Alexandria Engineering Journal, 2020, 59(3): 1 583-1 593.

[27] Ke G, Zhang J, Tian B, et al. Characteristic Analysis of Concrete Air Entraining Agents in Different Media[J]. Cement and Concrete Research, 2020, 135: 106 142.

[28] Robalo K, Soldado E, Costa H, et al. Efficiency of Cement Content and of Compactness on Mechanical Performance of Low Cement Concrete Designed with Packing Optimization[J]. Construction and Building Materials, 2021, 266: 121 077.

[29] Lai J, Qiu J, Fan H, et al. Freeze-Proof Method and Test Verification of a Cold Region Tunnel Employing Electric Heat Tracing[J]. Tunnelling and Underground Space Technology, 2016, 60: 56-65.

[30] Liu P, Cui S, Li Z, et al. Influence of Surrounding Rock Temperature on Mechanical Property and Pore Structure of Concrete for Shotcrete Used in a Hot-Dry Environment of High-Temperature Geothermal Tunnel[J]. Construction and Building Materials, 2019, 207: 329-337.

[31] Li Y, Ingason H. Overview of Research on Fire Safety in Underground Road and Railway Tunnels[J]. Tunnelling and Underground Space Technology, 2018, 81: 568-589.

[32] BSI Standards Press. Methods of Testing Cement. Determination of Strength[S]. BS EN 196-1, 2016

[33] Chindaprasirt P, Rukzon S. Strength, Porosity and Corrosion Resistance of Ternary Blend Portland Cement, Rice Husk Ash and Fly Ash Mortar[J]. Construction and Building Materials, 2008, 22(8): 1 601-1 606.

[34] Ruuska T, Vinha J, Kivioja H. Measuring Thermal Conductivity and Specific Heat Capacity Values of Inhomogeneous Materials with a Heat Flow Meter Apparatus[J]. Journal of Building Engineering, 2017, 9: 135-141.

[35] Pan Z, Wang S, Liu Y, et al. The Hydration, Pore Structure and Strength of Cement-Based Material Prepared with Waste Soaking Solution from Acetic Acid Treatment of Regenerated Aggregates[J]. Journal of Cleaner Production, 2019, 235: 866-874.

[36] China Building Industry Press. Fireproof Coatings for Concrete Structure[S]. GB 28375-2012, 2012

[37] Batool F, Rafi M M, Bindiganavile V. Microstructure and Thermal Conductivity of Cement-Based Foam: a Review[J]. Journal of Building Engineering, 2018, 20: 696-704.

[38] Ledesma R, Lopes N, Bacca K, et al. Zeolite and Fly Ash in the Composition of Oil Well Cement: Evaluation of Degradation by CO₂ under Geological Storage Condition[J]. Journal of Petroleum Science and Engineering, 2020, 185: 106 656.

[39] Kurtay M, Gerengi H, Kocak Y. The Effect of Caffeine Molecule on the Physico-Chemical Properties of Blended Cement[J]. Construction and Building Materials, 2020, 255: 119 394.

[40] Paradiso P, Santos R L, Horta R B, et al. Formation of Nanocrystalline Tobermorite in Calcium Silicate Binders with Low C/S Ratio[J]. Acta Materialia, 2018, 152: 7-15.

[41] Kupwade-patil K, Palkovic S, Bumajdad A, et al. Use of Silica Fume and Natural Volcanic Ash as a Replacement to Portland Cement: Micro and Pore Structural Investigation Using NMR, XRD, FTIR and X-Ray Microtomography[J]. Construction and Building Materials, 2018, 158: 574-590.

[42] Berger S, Coumes C, Lebescop P, et al. Influence of a Thermal Cycle at Early Age on the Hydration of Calcium Sulphoaluminate Cements with Variable Gypsum Contents[J]. Cement and Concrete Research, 2011, 41(2): 149-160.

[43] Xiao J, Xie M, Zhang C. Residual Compressive Behaviour of Pre-Heated High-Performance Concrete with Blast-Furnace-Slag[J]. Fire Safety Journal, 2006, 41(2): 91-98.

[44] Li G, Zhang L. Microstructure and Phase Transformation of Graphene-Cement Composites under High Temperature[J]. Composites Part B: Engineering, 2019, 166: 86-94.

[45] Liu M, Zhao Y, Xiao Y, et al. Performance of Cement Pastes Containing Sewage Sludge Ash at Elevated Temperatures[J]. Construction and Building Materials, 2019, 211: 785-795.

[46] Pan Z, Tao Z, Murphy T, et al. High Temperature Performance of Mortars Containing Fine Glass Powders[J]. Journal of Cleaner Production, 2017, 162: 16-26.

[47] Ahn Y, Jang J, Lee H. Mechanical Properties of Lightweight Concrete Made with Coal Ashes after Exposure to Elevated Temperatures[J]. Cement and Concrete Composites, 2016, 72: 27-38.

[48] Huang G, Pudasainee D, Gupta R, et al. Hydration Reaction and Strength Development of Calcium Sulfoaluminate Cement-Based Mortar Cured at Cold Temperatures[J]. Construction and Building Materials, 2019, 224: 493-503.

[49] Myers R, L’hôpital E, Provis J, et al. Effect of Temperature and Aluminium on Calcium (Alumino)Silicate Hydrate Chemistry under Equilibrium Conditions[J]. Cement and Concrete Research, 2015, 68: 83-93.

[50] Xu W, Zhang Y, Liu B. Influence of Silica Fume and Low Curing Temperature on Mechanical Property of Cemented Paste Backfill[J]. Construction and Building Materials, 2020, 254: 119 305.

[51] Husem M, Gozutok S. The Effects of Low Temperature Curing on the Compressive Strength of Ordinary and High Performance Concrete[J]. Construction & Building Materials, 2005, 19(1): 49-53.

[52] Cai H, Jiang Y, Feng J, et al. Nanostructure Evolution of Silica Aerogels under Rapid Heating from 600 to 1 300 °C via In-situ TEM Observation[J]. Ceramics International, 2020, 46(8): 12 489-12 498. Part B

[53] Xu H, Xing Z, Wang F, et al. Review on Heat Conduction, Heat Convection, Thermal Radiation and Phase Change Heat Transfer of Nanofluids in Porous Media: Fundamentals and Applications[J]. Chemical Engineering Science, 2019, 195: 462-483.

[54] Arioz O. Effects of Elevated Temperatures on Properties of Concrete[J]. Fire Safety Journal, 2007, 42(8): 516-522.

[55] Szelag M. Evaluation of Cracking Patterns of Cement Paste Containing Polypropylene Fibers[J]. Composite Structures, 2019, 220: 402-11.