Effect of post-weld heat treatment on mechanical characteristics of AZ31 magnesium alloy welded joints

Abstract

Tungsten inert gas (TIG) welding was performed on 2.7 mm thick commercial extruded AZ31B magnesium alloy plates. We investigated the effect of post-weld heat treatment (PWHT) on the microstructure, mechanical properties and precipitated phase of the weld joints. The results showed that during the annealing treatment (200 °C-1 h, 250 °C-1 h, 300 °C-1 h, 350 °C-1 h, 400 °C-1 h, and 450 °C-1 h), the average grain size in the weld seam was the minimum after annealing at 400 °C for 1 hour, and then abnormally grew up after annealing at 450 °C for 1 hour. The mechanical properties enhanced when the joints were processed from 200 °C-1 h to 400 °C-1 h but sharply decreased with increasing annealing temperature. In contrast to the annealing treatment, solution treatment (250 °C-10 h, 300 °C-10 h, 350 °C-10 h, 400 °C-10 h, and 450 °C-10 h) exhibited a better ductility but a slight deterioration in tensile strength. Especially speaking, no eutectic compounds (such as Mg₁₇Al₁₂) were observed in the weld seam. The supersaturated Al atoms were precipitated in a coarse spherical shape dispersed in the weld seam. The precipitated Al atoms dissolved in the matrix substances at the condition (400 °C-1 h) or (250 °C-10 h). The solution treatment caused grain coarsening and precipitated Al atoms dissolved in the weld seam substantially, which resulted in a drop in micro-hardness at the weld seam compared to the area of the annealed joints.

Keywords

magnesium alloy / welded joint / heat treatments / microstructure / mechanical properties

References

[1] Mordike BL, Ebert T. Magnesium: Properties Applications Potential[J]. Materials Science and Engineering: A, 2001, 302: 37-45.

[2] Mustafa, Kemal, Kulekci. Magnesium and Its Alloys Applications in Automotive Industry[J]. International Journal of Advanced Manufacturing Technology, 2008, 39: 851-865.

[3] Ma L, Qiao PX, Long WM, et al. Interface Characteristics and Mechanical Properties of the Induction Brazed Joint of Magnesium Alloy AZ31B with an Al–based Filler Metal[J]. Materials and Design, 2012, 37: 465-469.

[4] Manuel M, Louis G H, Ravi V, et al. Microstructural Effects of AZ31 Magnesium Alloy on Its Tensile Deformation and Failure Behaviors[J]. Materials Science and Engineering: A, 2006, 418: 341-356.

[5] Commin L, Dumont M, Masse J, et al. Friction Stir Welding of AZ31 Magnesium Alloy Rolled Sheets: Influence of Processing Parameters[J]. Acta Materialia, 2009, 57: 326-334.

[6] Krishnan K N. The Effect of Post Weld Heat Treatment on the Properties of 6061 Friction Stir Welded Joints[J]. Journal of Materials Science, 2002, 37: 473-480.

[7] Smith C, Pistorius PGH, Wannenburg J. The Effect of a Long Post Weld Heat Treatment on the Integrity of a Welded Joint in a Pressure Vessel Steel[J]. International Journal of Pressure Vessels and Piping, 1997, 70: 183-195.

[8] Ravi S, Balasubramanian V, Nemat Nasser S. Influences of Post Weld Heat Treatment on Fatigue Life Prediction of Strength Mis–matched HSLA Steel Welds[J]. International Journal of Fatigue, 2005, 27: 547-553.

[9] Elangovan K, Balasubramanian V. Influences of Post-Weld Heat Treatment on Tensile Properties of Friction Stir-Welded AA6061 Aluminum Alloy Joints[J]. Materials Characterization, 2008, 59: 1168-1177.

[10] Hu ZL, Yuan SJ, Wang XS, et al. Effect of Post-Weld Heat Treatment on the Microstructure and Plastic Deformation Behavior of Friction Stir Welded 2024[J]. Materials and Design, 2011, 32: 5055-5060.

[11] Hakan A, Ali B, Ismail Durgun. The Effect of Post-Weld Heat Treatment on the Mechanical Properties of 2024-T4 Friction Stir-Welded joints[J]. Materials and Design, 2010, 31: 2568-2577.

[12] Sullivan A, Robson JD. Microstructural Properties of Friction Stir Welded and Post Weld Heat Treated 7449 Aluminium Alloy Thick Plate[J]. Materials Science and Engineering: A, 2008, 478: 351-360.

[13] Fukumoto S, Yamamoto D, Tomita T, et al. Effect of Post Weld Heat Treatment on Microstructures and Mechanical Properties of AZ31B Friction Welded Joint[J]. Materials Transactions, 2007, 48: 44-52.

[14] Standards Press of China. Recommended Joint Preparation for Gas Welding, Manual Metal Arc Welding, Gas-Shield Arc Welding and Beam Welding[S]. 2008

[15] Chen ZH. Wrought Magnesium Alloy[M]. 2005 Beijing: Chemical Industry Press.

[16] Standards Press of China. Metallic Materials-Tensile Testing at Room Temperature[S]. 2010

[17] Yan ZF, Zhang HX, Wang WX, et al. Infrared Thermography Technology Predicting Fatigue Property of AZ31B Magnesium Alloy[J]. Materials for Mechanical Engineering, 2012, 36(2): 72-75.

[18] EO Hall. The Deformation and Ageing of Mild Steel: III Discussion of Results[J]. Proceedings of the Physical Society, 1951, 64: 742-752.

[19] NJ Petch. The Cleavage Strength of Polycrystals[J]. The Journal of the Iron and Steel Institute, 1953, 174: 25-28.

[20] NAGASAKI R, SHIRAISHI Kensuke. The Effect of Grain Size on the Tensile Properties of Magnox AL80[J]. Journal of Nuclear Science and Technology, 2012, 2(9): 369-374.

[21] Pavel L, Zuzanka Trojanová. Influence of Grain Size on Ductility of Magnesium Alloys[J]. Materials Engineering-Materiálové inžinierstvo, 2011, 18: 110-114.

[22] Atwell DL, Barnett MR, Hutchinson WB. The Effect of Initial Grain Size and Temperature on the Tensile Properties of Magnesium Alloy AZ31 Sheet[J]. Materials Science and Engineering: A, 2012, 549: 1-6.

[23] Lu L, LIU T, CHEN Y, et al. Deformation and Fracture Behavior of Hot Extruded Mg Alloys AZ31[J]. Materials Characterization, 2012, 67: 93-100.

[24] Aydin H, Bayram A, Uguz A, et al. Tensile Properties of Friction Stir Welded Joints of 2024 Aluminum Alloys in Different Heat-Treated-State[J]. Materials and Design, 2009, 30(6): 2211-2221.

[25] Ashby MF, Jones DRH. Engineering Materials 1[J]. 1980 Oxford: Pergamon Press.

[26] Sato YS, Park SHC, Kokawa H. Microstructural Factors Governing Hardness in Friction-Stir Welds of Solid-Solution-Hardened Al Alloys[J]. Metallurgical and Materials Transactions A, 2001, 32(12): 3033-3042.