Comparative study on constitutive models to predict flow stress of Fe-Cr-Ni preform reinforced Al-Si-Cu-Ni-Mg composite

Abstract

The isothermal compression tests were carried out on Gleeble-3500 thermal-mechanical simulation machine in a temperature range of 298-473 K and strain rate range of 0.001-10 s^-1. The experimental results show that the flow stress data are negatively correlated with temperature for temperature softening, and the strain rates sensitivity of this composite increases with elevating temperature. Based on the experimental data, Johnson-Cook, modified Johnson-Cook and Arrhenius constitutive models were established. The accuracy of these three constitutive models was analyzed and compared. The results show that the values predicted by Johnson-Cook model could not agree well with the experimental values. The prediction accuracy of Arrhenius model is higher than that of Johnson-Cook model but lower than that of the Modified Johnson-Cook model.

Keywords

Fe-Cr-Ni porous preform / composite / isothermal compression / constitutive model

References

[1] Liu B, Huang W M, Wang H W, et al. Compressive Behavior of High Particle Content B4C/Al Composite at Elevated Temperature[J]. Trans. Non ferr. Metal. Soc., 2013, 23: 2826-2832.

[2] Marchi C S, Cao F H, Kouzeli M, et al. Quasi-static and Dynamic Compression of Aluminum-oxide Particle Reinforced Pure Aluminum[J]. Mater. Sci. Eng. A, 2002, 337: 202-211.

[3] Wegner L D, Gibson L J. Mechanical Behavior of Interpenetrating Phase Composites-I: Modelling[J]. Int. J. Mech. Sci., 2000, 42: 925-942.

[4] Wegner L D, Gibson L J. Mechanical Behavior of Interpenetrating Phase Composites-II: A Case Study of a Three-dimensionally Printed Material[J]. Int. J. Mech. Sci., 2000, 42: 943-964.

[5] Wegner L D, Gibson L J. Mechanical Behavior of Interpenetrating Phase Composites-III: Resin-impregnated Porous Stainless Steel[J]. Int. J. Mech. Sci., 2001, 43: 1061-1072.

[6] Johnson G R, Cook W H. Proceedings of the 7th International Symposium on Ballistics, 1983

[7] Johnson G R, Cook W H. Fracture Characteristics of Three Metals Subjected to Various Strains, Strain Rates, Temperatures and Pressures[J]. Eng. Fract. Mech., 1985, 21(1): 31-48.

[8] He A, Xie G L, Zhang H L, et al. A Comparative Study on Johnson- Cook, Modified Johnson-Cook and Arrhenius-type Constitutive Models to Predict the High Temperature Flow Stress in 20CrMo Alloy Steel[J]. Mater. Des., 2013, 52: 677-685.

[9] Li H P, He L F, Zhao G Q, et al. Constitutive Relationship of Hot Stamping Boron Steel B1500HS Based on the Modified Arrhenius and Johnson-Cook Model[J]. Mater. Sci. Eng. A, 2013, 580: 330-348.

[10] Li H Y, Wang X F, Duan J Y, et al. A Modified Johnson Cook Model for Elevated Temperature Flow Behavior of T24 Steel[J]. Mater. Sci. Eng. A, 2013, 577: 138-146.

[11] Li H Y, Li Y H, Wang X F, et al. A Comparative Study on Modified Johnson-Cook, Modified Zerilli-Armstrong and Arrhenius-type Constitutive Models to Predict the Hot Deformation Behavior in 28CrMn-MoV Steel[J]. Mater. Des., 2013, 49: 493-501.

[12] Lin Y C, Chen X M, Liu G. A Modified Johnson-Cook Model for Tensile Behaviors of Typical High-strength Alloy Steel[J]. Mater. Sci. Eng. A., 2010, 527: 6980-6986.

[13] Lin Y C, Chen X M. A Combined Johnson-Cook and Zerilli-Armstrong Model for Hot Compressed Typical High-strength Alloy Steel[J]. Comput. Mater. Sci., 2010, 49: 628-633.

[14] Liu W Y, Zhao H, Li D, et al. Hot Deformation Behavior of AA7085 Aluminum Alloy During Isothermal Compression at Elevated Temperature[J]. Mater. Sci. Eng. A, 2014, 596: 176-182.

[15] Quan G Z, Shi Y, Wang Y X, et al. Constitutive Modeling for the Dynamic Recrystallization Evolution of AZ80 Magnesium Alloy Based on Stress-strain Data[J]. Mater. Sci. Eng. A, 2011, 528(28): 8051-8059.