Optimization of abrasive water jet cutting of ductile materials

Abstract

Full factorial design of experiments was developed in order to investigate the effects of jet pressure, abrasive mixing rate, cutting feed, and plate thickness upon three response variables, surface finish of cutting wear zone, percentage proportion of striation free area, and maximum width of cut. The set of sixteen experiments was performed on each of the following two ductile materials: AISI 4340 (high strength low alloy steel, hardened to 49HRc) and Aluminum 2219. Analysis of Variance (ANOVA) was performed on experimental data in order to determine the significance of effects of different parameters on the performance measures. It was found that cutting feed and thickness were highly influential parameters, while abrasive mixing rate is influential upon surface roughness only. Strong interaction was found between jet pressure and workpiece material. Multi-criteria numerical optimization was performed in order to simultaneously maximize/minimize different combinations of performance measures.

Keywords

abrasive jet cutting / ductile metals / material processing / striations / optimization

References

[1] Jou M. Analysis of the Stability of Water-Jet Cutting with Linear Theory[J]. J. Mater. Process. Technol., 2000, 104: 17-20.

[2] Junkar M., Jurisevic B., Fajdiga M., . Finite Element Analysis of Single-Particle Impact in Abrasive Water Jet Machining[J]. Int. J. Impact Eng., 2006, 32: 1 095-1 112.

[3] Chen F.L., Siores E. The Effect of Cutting Jet Variation on Striation Formation in Abrasive Water Jet Cutting[J]. Int. J. Machine Tools & Manuf., 2001, 41: 1 479-1 486.

[4] Lemma E., Chen L., Siores E., . Study of Cutting Fiber-Reinforced Composites by Using Abrasive Water-Jet with Cutting Head Oscillation[J]. Compos. Struct., 2002, 57: 297-303.

[5] J Chao, ES Geskin. Experimental Study of the Striation Formation and Spectral Analysis of the Abrasive Water Jet Generated Surfaces[C]. Proc. 7th American Water Jet Conference, 1993: 27–41

[6] Hashish M. A Modeling Study of Metal Cutting with Water Jets[J]. J. Eng. Mater. Technol., 1984, 106: 88-100.

[7] Hashish M. Characteristics of Surfaces Machined with Abrasive Water Jets[J]. J. Eng. Mater. Technol., 1991, 113: 354-362.

[8] Bittar J.G.A. A Study of Erosion Phenomenon-Part I[J]. Wear, 1963, 6: 5-21.

[9] Bittar J.G.A. A Study of Erosion Phenomenon-Part II[J]. Wear, 1963, 6: 169-190.

[10] Paul S., Hoogstrate S.M., van Luttervelt C.A., . Analytical Modeling of the Total Depth of Cut in the Abrasive Water Jet Machining of Polycrystalline Brittle Material[J]. J. Mater. Process. Technol., 1998, 73: 206-212.

[11] Hashish M. Pressure Effects in Abrasive Water Jet Machining[J]. J. Eng. Mater. Technol., 1989, 111: 221-228.

[12] E Capello, R Groppetti. On a Simplified Model for Hydro Control and Optimization[C]. Proc. 7 ^th American Water Jet Conference, 1993: 157–174

[13] L Chen, E Siores, Y Morsi, et al. A Study of Surface Striation Formation Mechanisms Applied to Abrasive Water Jet Process[J]. Ann. CIRP, 1997: 570–575

[14] Patel K. J. Quantitative Evaluation of Abrasive Contamination in Ductile Material during Abrasive Water Jet Machining and Minimizing with a Nozzle Head Oscillation Technique[J]. Int. J. Machine Tools & Manuf., 2004, 44: 1 125-1 132.

[15] Wang J. Abrasive Water Jet Machining of Polymer Matrix Composites-Cutting Performance, Erosive Process and Predictive Models[J]. Int. J. Advanced Manufac. Technol., 1999, 15: 757-768.

[16] Derringer G., Suich R. Simultaneous Optimization of Several Response Variables[J]. J. Qual. Technol., 1980, 12: 214-219.