Effect of rolling passes on AZ31 Mg alloy subjected to cross-rolling and cryogenic treatment

Abstract

In this paper, the multi cross-rolling and cryogenic treatment were adopted to process the AZ31 Mg alloy to study the influence of passes and cryogenic treatment on cross-rolled AZ31 Mg alloy. The tensile properties and hardness were tested. The microstructure was characterized using electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) in order to elucidate the influencing mechanism. The results indicate that the treatment method can significantly improve the mechanical properties of AZ31 Mg alloy. The 3-pass sample processed by cryogenic treatment shows the highest strength (351 MPa) and has the highest hardness (76.1HV) and best hardness uniformity (standard deviation=0.9HV). The 2-pass sample has the highest ductility among all the samples but poor hardness evenness. The strengthening mechanism of 3-pass sample can be attributed to the fine grains, bimodal structure, high dislocation density, and precipitation strengthening. Due to repeated heat preservation of 4-pass and 5-pass, their comprehensive performances decrease.

Keywords

AZ31 Mg alloy / cross-rolling / cryogenic treatment / pass / mechanical properties

References

[1] Yang C-y, Wang L-f, Xue L-l, et al. . Weakened in-plane anisotropy of AZ31 magnesium alloy sheet induced by pre-enhanced non-basal slips during hot rolling [J]. Journal of Central South University, 2025, 32(3): 706-726.

[2] Liu X, He D-d, Zhu B-w, et al. . The ordered orientation gradient “sandwich” texture induced high strength-ductility in AZ31 magnesium alloy [J]. Scripta Materialia, 2024, 253: 116296.

[3] Li J-r, Xie D-s, Yu H-s, et al. . Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet [J]. Journal of Alloys and Compounds, 2020, 835: 155228.

[4] Han T-z, Zhang H, Yang M-x, et al. . Microstructural evolution and mechanical properties of AZ31 Mg alloy fabricated by a novel bifurcation-equal channel angular pressing [J]. Journal of Central South University, 2024, 31(9): 2961-2972.

[5] Nazeer F, Long J-y, Yang Z, et al. . Superplastic deformation behavior of Mg alloys: A review [J]. Journal of Magnesium and Alloys, 2022, 10(1): 97-109.

[6] Zhu B-w, Cui Y, Xu K, et al. . Hard-soft-hard layered structure for enhanced mechanical properties in corrugated rolled AZ31 magnesium alloy sheets [J]. Journal of Materials Research and Technology, 2025, 35: 3205-3216.

[7] Wang Q-h, Jiang B, Liu L-t, et al. . Reduction per pass effect on texture traits and mechanical anisotropy of Mg-Al-Zn-Mn-Ca alloy subjected to unidirectional and cross rolling [J]. Journal of Materials Research and Technology, 2020, 9(5): 9607-9619.

[8] Yao Y, Liu C-m, Wan Y-c, et al. . Microstructure, texture and mechanical anisotropy of Mg-Gd-Y-Zr sheets processed via different rolling routes and reductions [J]. Materials Characterization, 2020, 161: 110120.

[9] Zhang P-f, Xin Y-c, Zhang L, et al. . On the texture memory effect of a cross-rolled Mg-2Zn-2Gd plate after unidirectional rolling [J]. Journal of Materials Science & Technology, 2020, 41: 98-104.

[10] Pei D, Wang L, Ge Z-b, et al. . Dynamic precipitation and twinning-induced dynamic recrystallization in Mg-6Al-3Sn-1Zn alloy during multi-pass high-speed rolling [J]. Journal of Materials Research and Technology, 2024, 30: 2200-2210.

[11] Ma R, Zhao Y-q, Wang Y-nong. Grain refinement and mechanical properties improvement of AZ31 Mg alloy sheet obtained by two - stage rolling [J]. Materials Science and Engineering A, 2017, 691: 81-87.

[12] Podgornik B, Paulin I, Zajec B, et al. . Deep cryogenic treatment of tool steels [J]. Journal of Materials Processing Technology, 2016, 229: 398-406.

[13] Li H-z, Tong W-p, Cui J-j, et al. . The influence of deep cryogenic treatment on the properties of high-vanadium alloy steel [J]. Materials Science and Engineering A, 2016, 662: 356-362.

[14] Gonçalves V R M, Podgornik B, Leskovšek V, et al. . Influence of deep cryogenic treatment on the mechanical properties of spring steels [J]. Journal of Materials Engineering and Performance, 2019, 28(2): 769-775.

[15] Hu J-q, Yang G-x, Liu Z, et al. . Effects of deep cryogenic treatment on microstructure, mechanical, and corrosion of ZK60 Mg alloy [J]. Journal of Materials Research and Technology, 2023, 26: 3686-3700.

[16] Kumar S D, Kumar S S. Effect of heat treatment conditions and cryogenic treatment on microhardness and tensile properties of AZ31B alloy [J]. Journal of Materials Engineering and Performance, 2023, 32(19): 8786-8794.

[17] Chen X, Liu C-m, Wan Y-c, et al. . Formation of nanocrystalline AZ31B Mg alloys via cryogenic rotary swaging [J]. Journal of Magnesium and Alloys, 2023, 11(5): 1580-1591.

[18] Dong N-n, Sun L-x, Ma H-b, et al. . Effects of cryogenic treatment on microstructures and mechanical properties of Mg-2Nd-4Zn alloy [J]. Materials Letters, 2021, 305: 130699.

[19] Lin T, Zhou J-x, Jing C-n, et al. . Improving mechanical properties of ZK60 magnesium alloy by cryogenic treatment before hot extrusion [J]. High Temperature Materials and Processes, 2020, 39(1): 200-208.

[20] Jia J-j, Meng M, Zhang Z-m, et al. . Effect of deep cryogenic treatment on the microstructure and tensile property of Mg-9Gd-4Y-2Zn-0.5Zr alloy [J]. Journal of Materials Research and Technology, 2022, 16: 74-87.

[21] Shen T-y, Liu H, Zhang J-l, et al. . The improvement on mechanical anisotropy of AZ31 magnesium alloy sheets by multi cross-rolling process [J]. Journal of Alloys and Compounds, 2023, 963: 171252.

[22] Yin W-j, Briffod F, Shiraiwa T, et al. . Mechanical properties and failure mechanisms of Mg-Zn-Y alloys with different extrusion ratio and LPSO volume fraction [J]. Journal of Magnesium and Alloys, 2022, 10(8): 2158-2172.

[23] Ma C-h, Ma X-l, Pei X, et al. . Effect of rolling reduction on the microstructure and mechanical properties of hot-rolled Mg-Li-Al-Ca alloys [J]. Materials Today Communications, 2023, 37: 107469.

[24] Li J-l, Chen H-c, Wu D, et al. . Strain rate-dependent tension-compression asymmetry in cast Mg-Gd-Y alloy: Insights into slip and twinning mechanisms [J]. Journal of Materials Science & Technology, 2025, 219: 134-146.

[25] Wang D-l, Xu D-k, Wang B-j, et al. . Effect of cross rolling on the microstructure and mechanical performance of a dual-phase structured Mg-8Li-6Zn-1Y (in wt.%) alloy [J]. Journal of Materials Science & Technology, 2024, 176: 132-144.

[26] Stanford N. The effect of rare earth elements on the behaviour of magnesium-based alloys: Part 2-recrystallisation and texture development [J]. Materials Science and Engineering A, 2013, 565: 469-475.

[27] Yao Y, Liu C-m, Wan Y-c, et al. . Microstructure, texture and mechanical anisotropy of Mg-Gd-Y-Zr sheets processed via different rolling routes and reductions [J]. Materials Characterization, 2020, 161: 110120.

[28] Liu X, Zhu B-w, Wei F-a, et al. . Heterogeneous lamella mixed grain structures of strength-ductility synergy in medium strain rate rolled AZ31 magnesium sheets [J]. Materials Science and Engineering A, 2024, 916: 147387.

[29] Zha M, Zhang X-h, Zhang H, et al. . Achieving bimodal microstructure and enhanced tensile properties of Mg-9Al-1Zn alloy by tailoring deformation temperature during hard plate rolling (HPR) [J]. Journal of Alloys and Compounds, 2018, 765: 1228-1236.

[30] Zhang J, Xi G-q, Wan X, et al. . The dislocation-twin interaction and evolution of twin boundary in AZ31 Mg alloy [J]. Acta Materialia, 2017, 133: 208-216.

[31] Lentz M, Risse M, Schaefer N, et al. . Strength and ductility with {101¯1}:{101¯2}\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\{10\bar{1}1\}:\,\{10\bar{1}2\}$$\end{document} double twinning in a magnesium alloy [J]. Nature Communications, 2016, 7: 11068.

[32] Zhang H, Yang M-x, Hou M-j, et al. . Effect of pre-existing{101¯2}\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\{10\bar{1}2\}$$\end{document}extension twins on mechanical properties, microstructure evolution and dynamic recrystallization of AZ31 Mg alloy during uniaxial compression [J]. Materials Science and Engineering A, 2019, 744: 456-470.

[33] Zhao F, Suo T, Chen B, et al. . Strength-ductility combination of fine-grained magnesium alloy with high deformation twin density [J]. Journal of Alloys and Compounds, 2019, 798: 350-359.

[34] Alaneme K K, Anaele J U, Bodunrin M O. Hot deformation processing of shape memory alloys: A review of effects on plastic flow behaviour, deformation mechanisms, and functional characteristics [J]. Alexandria Engineering Journal, 2022, 61(12): 12759-12783.

[35] Mirzadeh H. Grain refinement of magnesium alloys by dynamic recrystallization (DRX): A review [J]. Journal of Materials Research and Technology, 2023, 25: 7050-7077.

[36] Yu H, Liu H, Jiang B-n, et al. . A comprehensive study of dynamic recrystallization behavior of Mg alloy with 3 wt.% Bi addition [J]. Metals, 2021, 11(5): 838.

[37] Fan Y-t, Lu L-w, Zhao H-l, et al. . Effect of deformation temperatures on microstructure of AQ80 magnesium alloy under repeated upsetting-extrusion [J]. Acta Metallurgica Sinica (English Letters), 2023, 36(10): 1649-1664.

[38] Che B, Lu L-w, Zhang J-l, et al. . Effects of cryogenic treatment on microstructure and mechanical properties of AZ31 magnesium alloy rolled at different paths [J]. Materials Science and Engineering A, 2022, 832: 142475.

[39] Lu F-m, Ma A-b, Jiang J-h, et al. . Enhanced mechanical properties and rolling formability of fine-grained Mg-Gd-Zn-Zr alloy produced by equal-channel angular pressing [J]. Journal of Alloys and Compounds, 2015, 643: 28-33.

[40] Chen W Z, Zhang W C, Zhang L X, et al. . Property improvements in fine-grained Mg-Zn-Zr alloy sheets produced by temperature-step-down multi-pass rolling [J]. Journal of Alloys and Compounds, 2015, 646: 195-203.

[41] Li L, Zhang C-c, Lv H, et al. . Texture development and tensile properties of Mg-Yb binary alloys during hot extrusion and subsequent annealing [J]. Journal of Magnesium and Alloys, 2022, 10(1): 249-265.

[42] Liu X, He D-d, Zhu B-w, et al. . Periodical mixed grain and mechanical properties of as-cast AZ31 magnesium alloy corrugated slab after single-pass medium-strain rate rolling with subsequent annealing [J]. Journal of Alloys and Compounds, 2025, 1014: 178741.

[43] Che B, Lu L-w, Zhang J-l, et al. . Effects of cryogenic treatment on microstructure and mechanical properties of AZ31 magnesium alloy rolled at different paths [J]. Materials Science and Engineering A, 2022, 832: 142475.

[44] Zha M, Ma X, Jia H-l, et al. . Dynamic precipitation and deformation behaviors of a bimodal-grained WE43 alloy with enhanced mechanical properties [J]. International Journal of Plasticity, 2023, 167: 103682.

[45] Wang Q-h, Jiang B, Tang A-t, et al. . Formation of the elliptical texture and its effect on the mechanical properties and stretch formability of dilute Mg-Sn-Y sheet by Zn addition [J]. Materials Science and Engineering A, 2019, 746: 259-275.

[46] Shen T-y, Liu H, Yang G-j, et al. . Influence of cryogenic treatment time on the mechanical properties of AZ31 magnesium alloy sheets after cross-rolling [J]. Journal of Alloys and Compounds, 2024, 986: 174096.

[47] Ganguly S, Reddy S T, Majhi J, et al. . Enhancing mechanical properties of squeeze-cast AZ91 magnesium alloy by combined additions of Sb and SiC nanoparticles [J]. Materials Science and Engineering A, 2021, 799: 140341.

[48] Sarvesha R, Alam W, Gokhale A, et al. . Quantitative assessment of second phase particles characteristics and its role on the deformation response of a Mg-8Al-0.5Zn alloy [J]. Materials Science and Engineering A, 2019, 759: 368-379.

[49] Liu X, Wan Q-h, Zhu B-w, et al. . Effect of low-angle grain boundary and twin on precipitation mechanism in pre-rolled AZ91 magnesium alloy [J]. Journal of Materials Science, 2024, 59(8): 3662-3675.

RIGHTS & PERMISSIONS

Central South University