Microstructure and properties of Cu-50Fe alloy produced by chemical co-precipitation and powder metallurgy

Abstract

Traditional casting preparation of Cu-Fe alloy is difficult, especially when Fe content is relatively high, because there is a metastable immiscible region of liquid components between copper (Cu) and iron (Fe), which causes serious compositional segregation in Cu-Fe alloys and leads to low strength and undesirable electrical conductivity of the alloys. In this study, Cu-50Fe alloy was fabricated by chemical co-precipitation and powder metallurgy. Cu-Fe mixed powders prepared by chemical co-precipitation have an average particle size of about 3.5 µm and a near-spherical shape. Copper and iron phases in the fabricated alloy intertwine with each other. After cold deformation, copper and iron phases are elongated along the cold deformation direction to form strips. During aging treatment, a number of Fe particles with diameter of 10–50 nm precipitate in Cu phases in the alloy. The tensile strength and electrical conductivity of the deformed and aged Cu-50Fe alloy are 651 MPa and 41.5%IACS, respectively.

Keywords

Cu-Fe alloy / chemical co-precipitation / powder metallurgy / mechanical properties / electrical conductivity

References

[1] ZhangP, YuanX-b, LiY-d, et al. . Influence of minor Ag addition on the microstructure and properties of powder metallurgy Cu-10wt% Fe alloy [J]. Journal of Alloys and Compounds, 2022, 904: 163983

[2] WangM, ZhangR, XiaoZ, et al. . Microstructure and properties of Cu-10wt% Fe alloy produced by double melt mixed casting and multi-stage thermomechanical treatment [J]. Journal of Alloys and Compounds, 2020, 820153323

[3] LiuS-c, JieJ-c, GuoZ-k, et al. . A comprehensive investigation on microstructure and magnetic properties of immiscible Cu-Fe alloys with variation of Fe content [J]. Materials Chemistry and Physics, 2019, 238121909

[4] StepanovN D, KuznetsovA V, SalishchevG A, et al. . Evolution of microstructure and mechanical properties in Cu-14%Fe alloy during severe cold rolling [J]. Materials Science and Engineering A, 2013, 564264-272

[5] WangC P, LiuX J, OhnumaI, et al. . Formation of immiscible alloy powders with egg-type microstructure [J]. Science, 2002, 297(5583): 990-993

[6] WuY H, WangW L, ChangJ, et al. . Evolution kinetics of microgravity facilitated spherical macrosegregation within immiscible alloys [J]. Journal of Alloys and Compounds, 2018, 763: 808-814

[7] LiuS-c, JieJ-c, DongB-w, et al. . Novel insight into evolution mechanism of second liquid-liquid phase separation in metastable immiscible Cu-Fe alloy [J]. Materials & Design, 2018, 156: 71-81

[8] HeJ, ZhaoJ-zhou. Behavior of Fe-rich phase during rapid solidification of Cu-Fe hypoperitectic alloy [J]. Materials Science and Engineering A, 2005, 404(1–2): 85-90

[9] WangH P, LüP, CaiX, et al. . Rapid solidification kinetics and mechanical property characteristics of Ni-Zr eutectic alloys processed under electromagnetic levitation state [J]. Materials Science and Engineering A, 2020, 772: 138660

[10] WangM, JiangY-b, LiZ, et al. . Microstructure evolution and deformation behaviour of Cu-10wt%Fe alloy during cold rolling [J]. Materials Science and Engineering A, 2021, 801140379

[11] ZhangC-z, ChenC-g, LiuX-h, et al. . High strength and high electrical conductivity in Cu-Fe alloys with nano and micro Fe particles [J]. Materials Science and Engineering A, 2022, 855143948

[12] ZhangC-f, YaoY-l, ZhangY-l, et al. . Preparation of ultra-fine fibrous Fe-Ni alloy powder by coordinated co-precipitation-direct reduction process [J]. Transactions of Nonferrous Metals Society of China, 2012, 22(12): 2972-2978

[13] MaoM, GanX, ZhouK, et al. . Effect of sintering temperature and aging process on microstructure and properties of Cu-Fe alloy prepared by Cu-Fe composite powder [J]. Materials Science and Engineering of Powder Metallurgy, 2021, 26(4): 363-371

[14] WangF-l, WakohK, LiY-p, et al. . Study of microstructure evolution and properties of Cu-Fe microcomposites produced by a pre-alloyed powder method [J]. Materials & Design, 2017, 12664-72

[15] GoY S, SpitzigW A. Strengthening in deformation-processed Cu-20%Fe composite [J]. Journal of Materials Science, 1991, 26: 163-171

[16] JermanG A, AndersonI E, VerhoevenJ D. Strength and electrical conductivity of deformation-processed Cu-15 Vol Pct Fe alloys produced by powder metallurgy techniques [J]. Metallurgical Transactions A, 1993, 24(1): 35-42

[17] ShiG-d, ChenX-h, JiangH, et al. . Strengthening mechanisms of Fe nanoparticles for single crystal Cu-Fe alloy [J]. Materials Science and Engineering A, 2015, 636: 43-47

[18] LuoS B, WangW L, ChangJ, et al. . A comparative study of dendritic growth within undercooled liquid pure Fe and Fe₅₀Cu₅₀ alloy [J]. Acta Materialia, 2014, 69: 355-364

[19] MoonJ, ParkJ M, BaeJ W, et al. . A new strategy for designing immiscible medium-entropy alloys with excellent tensile properties [J]. Acta Materialia, 2020, 193: 71-82

[20] ZouJ, LuD-p, FuQ-f, et al. . Microstructure and properties of Cu-Fe deformation processed in situ composite [J]. Vacuum, 2019, 167: 54-58

[21] JeongE, HanS, GotoM, et al. . Effects of thermomechanical processing and trace amount of carbon addition on tensile properties of Cu-2.5Fe-0.1P alloys [J]. Materials Science and Engineering A, 2009, 520(1–2): 66-74

[22] MoustafaS F, DaoushW M. Synthesis of nano-sized Fe-Ni Powder by chemical process for magnetic applications [J]. Journal of Materials Processing Technology, 2007, 181(1–3): 59-63

[23] QuelennecX, MenandA, le BretonJ M, et al. . Homogeneous Cu-Fe supersaturated solid solutions prepared by severe plastic deformation [J]. Philosophical Magazine, 2010, 90(9): 1179-1195

[24] WangY F, WangM S, FangX T, et al. . Extra strengthening in a coarse/ultrafine grained laminate: Role of gradient interfaces [J]. International Journal of Plasticity, 2019, 123: 196-207

[25] ZhengZ-s, GuoP-s, LiJ-g, et al. . Effect of cold rolling on microstructure and mechanical properties of a Cu-Zn-Sn-Ni-Co-Si alloy for interconnecting devices [J]. Journal of Alloys and Compounds, 2020, 831(7): 154842

[26] ZhangZ-chao. Effect of aging treatment on hardness and electrical conductivity of polybasic copper alloy [J]. Material & Heat Treatment, 2009, 388144-146