Numerical study of effect of front cavity on hydrogen/air premixed combustion in a micro-combustion chamber

Abstract

The micro-combustion chamber is the key component for micro-TPV systems. To improve the combustor wall temperature level and its uniformity and efficiency an improved flat micro-combustor with a front cavity is built, and the combustion performance of the original and improved combustors of premixed H₂/air flames under various inlet velocities and equivalence ratios is numerically investigated. The effects of the front cavity height and length on the outer wall temperature and efficiency are also discussed. The front cavity significantly improves the average outer wall temperature, outer wall temperature uniformity, and combustion efficiency of the micro-combustor, increases the area of the high temperature zone, and enhances the heat transfer between the burned blends and inner walls. The micro-combustor with the front cavity length of 2.0 mm and height of 0.5 mm is suitable for micro-TPV system application due to the relatively high outer wall temperature, combustion efficiency, and the most uniform outer wall temperature.

Keywords

micro-combustor / hydrogen / front cavity / numerical study / energy conversion efficiency

References

[1] YanY-f, ZhangZ-e, ZhangL, WangX, LiuK, YangZ-qing. Investigation of auto thermal reforming of methane for hydrogen production in a spiral multi-cylinder micro-reactor used for mobile fuel cell [J]. International Journal of Hydrogen Energy, 2015, 40(4): 1886-1893

[2] ZuoH-y, LiuG-l E J-q, ZuoW, WeiK-x, HuW-y, TanL-q, ZhongD-qing. Catastrophic analysis on the stability of a large dish solar thermal power generation system with wind-induced vibration [J]. Solar Energy, 2019, 183: 40-49

[3] LiY-q, TangW, ChenY, LiuJ-w, LeeC F F. Potential of acetone-butanol-ethanol (ABE) as a biofuel [J]. Fuel, 2019, 242: 673-686

[4] PengQ-g E J-q, YangW M, XuH-p, ChenJ-w, ZhangF, MengT, QiuR-zhi. Experimental and numerical investigation of a micro-thermophotovoltaic system with different backward-facing steps and wall thicknesses [J]. Energy, 2019, 173: 540-547

[5] PengQ-g, WuY-f E J-q, YangW-m, XuH-p, LiZ-wei. Combustion characteristics and thermal performance of premixed hydrogen-air in a two-rearward-step micro tube [J]. Applied Energy, 2019, 242: 424-438

[6] PengQ-g E J-q, YangW-m, XuH-p, ChenJ-w, MengT, QiuR-zhi. Effects analysis on combustion and thermal performance enhancement of a nozzle-inlet micro tube fueled by the premixed hydrogen/air [J]. Energy, 2018, 160: 349-360

[7] MaW-w, XueX-p, LiuGang. Techno-economic evaluation for hybrid renewable energy system: Application and merits [J]. Energy, 2018, 159: 385-409

[8] LiuG, LiM-s, ZhouB-j, ChenY-y, LiaoS-ming. General indicator for techno-economic assessment of renewable energy resources [J]. Energy conversion and management, 2018, 156: 416-426

[9] WuG, LuZ-l, PanW-c, GuanY-h, LiS-s, JiC Z. Experimental demonstration of mitigating self-excited combustion oscillations using an electrical heater [J]. Applied Energy, 2019, 239: 331-342

[10] WuG, LuZ-l, XuX, PanW-c, WuW-w, LiJ, CiJ. Numerical investigation of aeroacoustics damping performance of a Helmholtz resonator: Effects of geometry, grazing and bias flow [J]. Aerospace Science and Technology, 2019, 86: 191-203

[11] ZhangL, ZhuJ-c, YanY-f, GuoH-l, YangZ-qing. Numerical investigation on the combustion characteristics of methane/air in a micro-combustor with a hollow hemispherical bluff body [J]. Energy Conversion and Management, 2015, 94: 293-299

[12] PengQ-g E J-q, ZhangZ-q, HuW-y, ZhaoX-huan. Investigation on the effects of front-cavity on flame location and thermal performance of a cylindrical micro-combustor [J]. Applied Thermal Engineering, 2018, 130: 541-551

[13] EJ-q, LiuH-j, ZhaoX-h, HanD-d, PengQ-g, ZuoW, MengT, QiuR-zhi. Investigation on the combustion performance enhancement of the premixed methane/air in a two-step micro-combustor [J]. Applied Thermal Engineering, 2018, 141: 114-125

[14] PanJ-f, ZhuJ, LiuQ-s, ZhuY-j, TangA-k, LuQ-bo. Effect of micro-pin-fin arrays on the heat transfer and combustion characteristics in the micro-combustor [J]. International Journal of Hydrogen Energy, 2017, 42(36): 23207-23217

[15] AkhtarS, KhanM N, KurniaJ C, ShamimT. Investigation of energy conversion and flame stability in a curved micro-combustor for thermo-photovoltaic (TPV) applications [J]. Applied energy, 2017, 192: 134-145

[16] WanJ-l, FanA-w, YaoH, LiuWei. Effect of thermal conductivity of solid wall on combustion efficiency of a micro-combustor with cavities [J]. Energy Conversion and Management, 2015, 96: 605-612

[17] WanJ-l, FanA-w, YaoH, LiuWei. Flame-anchoring mechanisms of a micro cavity-combustor for premixed H₂/air flame [J]. Chemical Engineering Journal, 20151726

[18] LiL-h, YangW, FanA-wu. Effect of the cavity aft ramp angle on combustion efficiency of lean hydrogen/air flames in a micro cavity-combustor [J]. International Journal of Hydrogen Energy, 2019, 44(11): 5623-5632

[19] WanJ-l, FanA-wu. Effect of channel gap distance on the flame blow-off limit in mesoscale channels with cavities for premixed CH₄/air flames [J]. Chemical Engineering Science, 2015, 132: 99-107

[20] ARAVIND B, RAGHURAM G K S, KISHORE V R, LUMAR S. Compact design of planar stepped micro-combustor for portable thermoelectric power generation [J]. Energy Conversion and Management, 2018, 156: 224 -234. DOI: 10.1016/j.enconman.2017.11.021.

[21] BagheriG, HosseiniS E, WahidM A. Effects of bluff body shape on the flame stability in premixed micro-combustion of hydrogen-air mixture [J]. Applied Thermal Engineering, 2014266272

[22] YilmazH, CamO, YilmazI. Effect of micro-combustor geometry on combustion and emission behavior of premixed hydrogen/air flames [J]. Energy, 2017, 135: 585-597

[23] YilmazI, YilmazH, CamO, IlbasM. Combustion characteristics of premixed hydrogen/air flames in a geometrically modified micro-combustor [J]. Fuel, 2018, 217: 536-543

[24] NiS-l, ZhaoD, SunY-z E J-qiang. Numerical and entropy studies of hydrogen-fuelled micro-combustors with different geometric shaped ribs [J]. International Journal of Hydrogen Energy, 2019, 44(14): 7692-7705

[25] EJ-q, PengQ-g, ZhaoX-h, ZhangZ-qing. Numerical investigation on the combustion characteristics of non-premixed hydrogen-air in a novel micro-combustor [J]. Applied Thermal Engineering, 2017, 110: 665-677

[26] WanJ-l, FanA-w, YaoHong. Effect of the length of a plate flame holder on flame blowout limit in a micro-combustor with preheating channels [J]. Combustion and Flame, 2016, 170: 53-62

[27] ZuoW E J-q, LiuH-l, PengQ-g, ZhaoX-h, ZhangZ-qing. Numerical investigations on an improved micro-cylindrical combustor with rectangular rib for enhancing heat transfer [J]. Applied Energy, 2016, 184: 77-87

[28] TangA-k, DengJ, XuY-m, PanJ-f, CaiTao. Experimental and numerical study of premixed propane/air combustion in the micro-planar combustor with a cross-plate insert [J]. Applied Thermal Engineering, 2018, 136: 177-184

[29] FanA-w, LiL-h, YangW, YuanZ-li. Comparison of combustion efficiency between micro-combustors with single-and double-layered walls: A numerical study [J]. Chemical Engineering and Processing-Process Intensification, 2019, 137: 39-47

[30] LiL-h, YuanZ-l, XiangY, FanA-wu. Numerical investigation on mixing performance and diffusion combustion characteristics of H2 and air in planar micro-combustor [J]. International Journal of Hydrogen Energy, 2018, 43(27): 12491-12498

[31] LiM-h, ZhangQ, LiG-x, LiP-xin. Effects of hydrogen addition on the performance of a pilot-ignition direct-injection natural gas engine: A numerical study [J]. Energy & Fuels, 2017, 31(4): 4407-4423

[32] TangA-k, XuY-m, PanJ-f, YangW-m, JiangD-y, LuQ-bo. Combustion characteristics and performance evaluation of premixed methane/air with hydrogen addition in a micro-planar combustor [J]. Chemical Engineering Science, 2015, 131: 235-242

[33] WuL, KobayashiN, LiZ-y, HuangH-yu. Experimental study on the effects of hydrogen addition on the emission and heat transfer characteristics of laminar methane diffusion flames with oxygen-enriched air [J]. International Journal of Hydrogen Energy, 2016, 41(3): 2023-2036

[34] WangW, ZuoZ-g, LiuJ-x, YangW-ming. The effects of hydrogen addition, inlet temperature and wall thermal conductivity on the flame-wall thermal coupling of premixed propane/air mixtures in meso-scale tubes [J]. International Journal of Hydrogen Energy, 2018, 43(22): 10458-10468

[35] AmaniE, AlizadehP, MoghadamR S. Micro-combustor performance enhancement by hydrogen addition in a combined baffle-bluff configuration [J]. International Journal of Hydrogen Energy, 2018, 43: 8127-8138

[36] TangA-k, XuY-m, ShanC-x, PanJ-f, LiuY-xian. A comparative study on combustion characteristics of methane, propane and hydrogen fuels in a micro-combustor [J]. International Journal of Hydrogen Energy, 2015, 40(46): 16587-16596

[37] KuoC H, RonneyP D. Numerical modeling of non-adiabatic heat-recirculating combustors [J]. Proceedings of the Combustion Institute, 2007, 31(2): 3277-3284

[38] LiJ, ZhaoZ-w, AndreiK A, DryerF L. An updated comprehensive kinetic model of hydrogen combustion [J]. International Journal of Chemical Kinetics, 2004, 36(10): 566-575

[39] WanJ-l, YangW, FanA-w, LiuY, YaoH, LiuW, DuY-q, ZhaoD-qing. A numerical investigation on combustion characteristics of H₂/air mixture in a micro-combustor with wall cavities [J]. International Journal of Hydrogen Energy, 2014, 39(15): 8138-8146