Effects of pre-deformation on microstructure and properties of Al–Cu–Mg–Ag heat-resistant alloy

Abstract

The effects of the pre-deformation on the microstructure, mechanical properties and corrosion resistance of Al–Cu–Mg–Ag alloys were investigated by means of hardness tests, tensile tests, intergranullar corrosion (IGC) tests and transmission electron microscopy (TEM), respectively. The results show that with the increase of deformation amount, the aging hardening rate increases while the strength of the alloy decreases and then increases. The sample with a pre-deformation of 6% possesses the highest tensile strength due to the refinedly and homogeneously distributed precipitations. The pre-deformation aging accelerates the heterogeneous nucleation of Ω and θ′ phases at dislocations, and also refines the precipitations both in the grains and along the grain boundaries. The precipitation of Ω phase is restrained while that of θ′ phase is accelerated in pre-deformed Al–Cu–Mg–Ag alloy compared with the sample without pre-deformation. In addition, the width of the precipitate free zone decreases with increasing the pre-deformation amount, leading to a narrower IGC passageway. This results in an enhanced IGC resistance of Al–Cu–Mg–Ag alloy treated by pre-deformation aging.

Keywords

Al–Cu–Mg–Ag alloy / pre-deformation / dislocation / intergranullar corrosion

References

[1] BakavosD, PrangnellPB, BesB, EberlF. The effect of silver on microstructural evolution in two 2xxx series Al-alloys with a high Cu:Mg ratio during ageing to a T8 temper [J]. Materials Science and Engineering A, 2008, 491: 214-223

[2] SuhI S, ParkJ K. Influence of the elastic strain energy on the nucleation of O phase in Al-Cu-Mg(-Ag) alloys [J]. Scripta Metall Mater, 1995, 33: 205-211

[3] BaiS, LiuZ Y, ZhouX W, XiaP, LiuM. Stress-induced thickening of O phase in Al–Cu–Mg alloys containing various Ag additions [J]. Materials Science and Engineering A, 2014, 589: 89-96

[4] HutchinsonC R, FanX, PennycookS J, ShifletG J. On the origin of the high coarsening resistance of O plates in Al–Cu–Mg–Ag Alloys [J]. Acta Materialia, 2001, 49: 2827-2841

[5] BaiS, LiuZ Y, GuY X, ZhouX W, ZengS M. Microstructures and fatigue fracture behavior of an Al–Cu–Mg–Ag alloy with a low Cu/Mg ratio [J]. Materials Science and Engineering A, 2011, 530: 473-480

[6] SongY-f, PanQ-l, WangY, LiC, FengLei. Elevated-temperature mechanical properties and thermal stability of Al–Cu–Mg–Ag heat-resistant alloy [J]. Journal of Central South University, 2014, 21(9): 3434-3441

[7] ReddyA S. Fatigue and creep deformed microstructures of aged alloys based on Al–4% Cu–0.3% Mg [J]. Materials & Design, 2008, 29: 763-768

[8] LiuY-b, LiuZ-y, LiY-t, XiaQ-k, ZhouJ, DuanS-liang. Effects of aging temperature on microstructures and mechanical properties of Al–5.06%Cu–0.44%Mg–0.55%Ag–0.30%Mn–0.17%Zr alloy [J]. Journal of Central South University: Science and Technology, 2008, 39(3): 532-537

[9] LiY, LiuZ Y, BaiS, ZhouX W, WangH, ZengS M. Enhanced mechanical properties in an Al–Cu–Mg–Ag alloy by duplex aging [J]. Materials Science and Engineering A, 2011, 528: 8060-8064

[10] LUMLEY R N, POLMEAR I J, MORTON A J. Heat treatment of age-hardenable aluminum alloys: US, 7025839B2 [P]. 2006-04-11.

[11] RingerS P, MuddleD M, PolmerI J. Effects of cold work on precipitation in Al-Cu-Mg-(Ag) and Al-Cu-Li(Mg-Ag) alloys [J]. Metallurgical and Materials Transactions A, 1995, 26: 1659-1671

[12] AlipourM, EmamyM, EbrahimiS, HS, AzarbarmasM, KaramouzM, RassizadehghaniJ. Effects of predeformation and heat treatment conditions in the SIMA process on properties of an Al–Zn–Mg–Cu alloy modified by Al–8B grain refiner [J]. Materials Science and Engineering A, 2011, 528: 4482-4490

[13] CaiY H, LangY J, CaoL Y, ZhangJ S. Enhanced grain refinement in AA7050 Al alloy by deformation-induced precipitation [J]. Materials Science and Engineering A, 2012, 549: 100-104

[14] AnL H, CaiY, LiuW, YuanS J, ZhuS Q, MengF C. Effect of pre-deformation on microstructure and mechanical properties of 2219 aluminum alloy sheet by thermomechanical treatment [J]. Transactions of Nonferrous Metals Society of China, 2012, 22: s370-s375

[15] LiH Z, ZhangX M, ChenM A, LiY F, LiangX P. Effect of pre-deformation on the stress corrosion cracking susceptibility of aluminum alloy 2519 [J]. Rare Metals, 2007, 26(4): 385-390

[16] ZhangX M, LiuL, YeL Y, LiuJ, LeiZ, SongJ C. Effect of pre-deformation of rolling combined with stretching on stress corrosion of aluminum alloy 2519A plate [J]. Transactions of Nonferrous Metals Society of China, 2012, 22(1): 8-15

[17] RingerS P, HonoK. Nucleation of precipitates in aged Al–Cu–Mg–(Ag) alloys with high Cu:Mg ratios [J]. Acta Materialia, 1996, 44: 1883-1898

[18] LiuX Y, PanQ L, LuC G, HeY B, LiW B, LiangW J. Microstructure and mechanical properties of Al–Cu–Mg–Mn–Zr alloy with trace amounts of Ag [J]. Materials Science and Engineering A, 2009, 525: 128-132

[19] ReichL, MurayamaM, HonoK. Evolution of O phase in an Al–Cu–Mg–Ag alloy—A three-dimensional atom probe study [J]. Acta Materialia, 1998, 46: 6053-6062

[20] LiuX Y, LiM J, GaoF, LiangS X, ZhangX L, CuiH X. Effects of aging treatment on the intergranular corrosion behavior of Al–Cu–Mg–Ag alloy [J]. Journal of Alloys and Compounds, 2015, 639: 263-267