Microstructure & texture evolution and magnetic properties of high magnetic-induction 6.5% Si electrical steel thin sheet fabricated by a specially designed rolling route

Abstract

Electrical steel sheets with 6.5% (mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm rolling both with interpass thermal treatment, and final annealing. The sheets were of 0.2 mm and 0.3 mm thick over 140 mm width. A detailed study of the microstructural and textural evolutions from the hot rolling to annealing was carried out by optical microscopy, X-ray diffraction and electron backscattered diffraction. The hot rolled sheet characterized by near-equiaxed grains was dominated by the mixture of <001>//ND fiber (λ-fiber), <110>//RD fiber (α-fiber) and <111>//ND fiber (γ-fiber) textures owing to the partial recrystallization and strain induced boundary migration (SIBM) during the hot rolling interpass thermal treatment. The static recovery and SIBM during the warm rolling interpass thermal treatment result in large and elongated warm rolling grains. The warm rolling texture is dominated by obvious λ, Goss and strong γ-fiber textures. The application of the interpass thermal treatment during hot and warm rolling significantly enhances the impact of SIBM during annealing, which is responsible for the formation of the moderate λ-fiber, some near-λ fiber texture components and the obviously weakened γ-fiber texture in the annealed sheet, leading to a higher magnetic induction compared to the commercially produced 6.5% Si steel by chemical vapor deposition (CVD).

Keywords

6.5% Si electrical steel / microstructure / texture / magnetic property

References

[1] HuneusH., GuntherK., KochmannT., PlutnioklV., SchoppaA.. Nonoriented magnetic steel with improved texture and permeability [J]. Journal of Materials Engineering and Performance, 1993, 2(2): 199-203

[2] AraiK. I., IshiyamaK.. Recent developments of new soft magnetic materials [J]. Journal of Magnetism and Magnetic Materials, 1994, 133(1/2/3): 233-237

[3] YuJ. H., ShinJ. S., BaeJ. S., LeeZ. H., LeeT. D., LeeH. M., LaverniaE. J.. The effect of heat treatments and Si contents on B2 ordering reaction in high-silicon steels [J]. Materials Science and Engineering A, 2001, 307(1/2): 29-34

[4] FuH.-d., ZhangZ.-h., PanH.-j., MoY.-k., XieJ.-x.. Warm/cold rolling processes for producing Fe-6.5% Si electrical steel with columnar grains [J]. International Journal of Minerals Metallurgy and Materials, 2013, 20: 535-540

[5] LiuH.-t., LiuZ.-y., QiuY.-q., SunY., WangG.-d.. Microstructure, texture and magnetic properties of strip casting Fe-6.2%Si steel sheet [J]. Journal of Materials Processing Technology, 2012, 212(9): 1941-1945

[6] LiuH.-t., LiuZ.-y., SunY., GaoF., WangG.-d.. Development of fiber recrystallization texture and magnetic property in Fe–6.5% Si thin sheet produced by strip casting and warm rolling method [J]. Materials Letters, 2013, 91: 150-153

[7] AbeM., TakadaY., MurakamiT., TanakaY., MiharaY.. Magnetic properties of commercially produced Fe-6.5% Si sheet [J]. Journal of Materials Engineering, 1989, 11(1): 109-116

[8] WangX., ZhangF., ZhuH.-f., PanH.-l.. Influence of temperature and diffusion time on manufacturing procedure of high silicon steel by CVD method [J]. Surface Technology, 2013, 42(1): 85-87

[9] Yos-YañezT., HoubaertY., FischerO., SchneiderJ.. Production of high silicon steel for electrical applications by thermomechanical processing [J]. Journal of Materials Processing Technology, 2003, 141: 132-137

[10] LinJ.-p., YeF., ChenG.-l., WangY.-l., LiangY.-f., JinJ.-n., LiuY.. Fabrication technology, microstructures and properties of Fe-6.5%Si alloy sheets by cold rolling [J]. Frontier Science, 2007, 2: 13-26

[11] YangK., LiangY.-f., YeF., LinJ.-p.. Fe-6. 5%Si electrical steel strip core losses detection and comparison by means of Epstein frame and inductor [J]. Materials Review, 2013, 27(22): 102-104

[12] QinZ., ZhuJ., WuJ., ZhanL., GongT., CongS.-h., ZhuB.-l.. Research status and development of the texture evolution of high silicon steel [J]. Materials Review, 2014, 28(6): 79-83

[13] LiuJ.-l., ShaY.-h., ZhangF., LiJ.-c., YaoY.-c., ZuoL.. Development of {210} <001> recrystallization texture in Fe–6.5% Si thin sheets [J]. Scripta Materialia, 2011, 65: 292-295

[14] StojakovicD., DohertyR. D., KalidindiS. R.. L<001> fiber texture in electric motor steels [J]. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 2008, 39: 1738-1746

[15] LeeD. N., JeongH. T.. The evolution of the Goss texture in silicon steel [J]. Scripta Materialia, 1998, 38(8): 1219-1223

[16] WagnerP., EnglerO., LuckeK.. Formation of Cu-type shear bands and their influence on deformation and texture of rolled fcc {112}<111> single crystals [J]. Acta Metallurgica et Materialia, 1995, 43: 3799-3812

[17] QuadirM. Z., DugganB. J.. A microstructural study of the origins of recrystallization textures in 75% warm rolled IF steel [J]. Acta Materialia, 2006, 54: 4337-4350

[18] BeckP. A., SperryP. R.. Strain induced boundary migration in high purity aluminium [J]. Journal of Applied Physics, 1950, 21: 150-152

[19] BellierS. P., DohertyR. D.. The structure of deformed aluminium and its recrystallization-investigations with transmission Kossel diffraction [J]. Acta Metallurgica, 1977, 25: 521-538

[20] BateP., HutchinsonB.. A re-evaluation of the mechanism of SIBM [J]. Scripta Materialia, 1997, 36(2): 195-198