Finite element analysis of contact fatigue and bending fatigue of a theoretical assembling straight bevel gear pair

Abstract

The aim of this work is to propose a 3D FE model of a theoretical assembling straight bevel gear pair to analyze the contact fatigue on the tooth surface and the bending fatigue in the tooth root. Based on the cumulative fatigue criterion and the stress-life equation, the key meshing states of the gear pair were investigated for the contact fatigue and the bending fatigue. Then, the reliability of the proposed model was proved by comparing the calculation result with the simulation result. Further study was performed to analyze the variation of the contact fatigue stress and the bending fatigue stress under different loads. Furthermore, the roles of the driving pinion and the driven gear pair were evaluated in the fatigue life of the straight bevel gear pair and the main fatigue failure mode was determined for the significant gear. The results show that the fatigue failure of the driving pinion is the main fatigue failure for the straight bevel gear pair and the bending fatigue failure is the main fatigue failure for the driving pinion.

Keywords

straight bevel gear / finite element method / contact fatigue / bending fatigue

References

[1] AsiO.. Fatigue failure of a helical gear in a gearbox [J]. Engineering Failure Analysis, 2006, 13(7): 1116-1125

[2] GuaglianoM., RivaE., GuidettiM.. Contact fatigue failure analysis of shot-peened gears [J]. Engineering Failure Analysis, 2002, 9(2): 147-158

[3] DuzcukouluH., ImrekH.. A new method for preventing premature pitting formation on spur gears [J]. Engineering Fracture Mechanics, 2008, 75(15): 4431-4438

[4] FernandesP. J. L.. Tooth bending fatigue failures in gears [J]. Engineering Failure Analysis, 1996, 3(3): 219-225

[5] PengC. H., LiuZ. Y., ZhuW. H.. Failure analysis of a gear tooth facture of a rolling mill decelerator [J]. Engineering Failure Analysis, 2011, 18(1): 25-35

[6] FonteM., ReisL., FreitasM.. Failure analysis of a gear wheel of a marine azimuth thruster [J]. Engineering Failure Analysis, 2011, 18(7): 1884-1888

[7] DonzellaG., FaccoliM., MazzuA., PetrogalliC., DesimoneH.. Influence of inclusion content on rolling contact fatigue in a gear steel: Experimental analysis and predictive modeling [J]. Engineering Fracture Mechanics, 2011, 78(16): 2761-74

[8] GlodezS., RenZ., FlasikerJ.. Surface fatigue of gear teeth flanks [J]. Computers and Structures, 1999, 73(1–5): 475-483

[9] AkataE., AltinbalikM. T., CanY.. Three point load application in single tooth bending fatigue test for evaluation of gear blank manufacturing methods [J]. International Journal of Fatigue, 2004, 26(7): 785-789

[10] KrambergerJ., SramlM., GlodezS., FlaskerJ., PotrcI.. Computational model for the analysis of bending fatigue in gears [J]. Computers and Structures, 2004, 82(23/24/25/26): 2261-2269

[11] KrambergerJ., SsramlM., PotrI., FlaskerJ.. Numerical calculation of bending fatigue life of thin-rim spur gears [J]. Engineering Fracture Mechanics, 2004, 71(4/5/6): 647-656

[12] GearK. M.. Tooth contact analysis and its application in the reduction of fatigue wear [J]. Wear, 2007, 262(11/12): 1281-1288

[13] PrasannavenkatesanR., ZhangJ., McdowellD. L., OlsonG. B., JouH. J.. 3D modeling of subsurface fatigue crack nucleation potency of primary inclusions in heat treated and shot peened martensitic gear steels [J]. International Journal of Fatigue, 2009, 31(7): 1176-89

[14] ZhangJ., PrasannavenkatesanR., ShenoyM. M., McdowellD. L.. Modeling fatigue crack nucleation at primary inclusions in carburized and shot-peened martensitic steel [J]. Engineering Fracture Mechanics, 2009, 76(3): 315-34

[15] WangB., HuaLin.. Accurate parametric modeling of spiral bevel gear based on CAD software Pro/E [J]. Journal of Wuhan University of Technology, 2010, 32(10): 99-103

[16] FongZ., TsayC.. A mathematical model for the tooth geometry of circular-cut spiral bevel gears [J]. J Mech Des, 1991, 13(30): 174-181

[17] TsayC. B., JengJ. W., FengH. S.. A mathematical model for ZK-type worm gear set [J]. Mech Mach Theor, 1995, 30(8): 777-789

[18] BairB., TsayC.. ZK-type dual-lead worm and worm gear drives: Contact teeth, contact ratios and kinematic errors [J]. J Mech Des, 1998, 120(10): 422-428

[19] DUDLEY D W. Handbook of practical gear design [M]. New York: McGraw-Hill Book Co, 1994: 215–223.

[20] LITVIN F L Gear Geometry and Applied Theory [M]. PTR Prentice Hall, 1994: 318–324.

[21] LitvinF. L., AlfonsofuentesN., Ignaciogonzalez-PerezM.. Modified involute helical gears: Computerized design, simulation of meshing and stress analysis [J]. Computer Methods in Applied Mechanics and Engineering, 2003, 192(33/34): 3619-3655

[22] LitvinF. L., Gonzalez-PerezI., FuentesA., HayasakaK., YukishimaK.. Topology of modified surfaces of involute helical gears with line contact developed for improvement of bearing contact, reduction of transmission errors, and stress analysis [J]. Mathematical and Computer Modeling, 2005, 42(9/10): 1063-1078

[23] LuJ., LitvinF. L., ChenJ. S.. Load share and finite element stress analysis for double circular-arc helical gears [J]. Mathematical and Computer Modeling, 1995, 21(10): 13-30

[24] ZienkiewiczO. C.The finite element Method [M], 1977LondonMcGraw-Hill124-263

[25] NiD.Application of ANSYS to mechanics [M], 2003LondonPublishing House of Electronics Industry241-292

[26] WangZ.-guang.Fatigue of Materials [M], 1999BeijingNational Defense Industry Press162-163

[27] ZengC.-h., GuoK.-min.Fatigue [M], 1984BeijingScience Press15-16

[28] ZhuX.-lu.Handbook of gear design [M], 2004BeijingChemical Industry Press124-125

[29] Mechanical design manual editorial committee. Gear transmission [M].Machinerys Handbook, 2007BeijingMechanic industry Press67-68