Effect of cooling modes on microstructure and electrochemical performance of LiFePO₄

Abstract

LiFePO₄ was prepared by heating the pre-decomposed precursor mixtures sealed in vacuum quartz-tube. Three kinds of cooling modes including nature cooling, air quenching, and water quenching were applied to comparing the effects of cooling modes on the microstructure and electrochemical characteristics of the material. The results indicate that the water quenching mode can control overgrowth of the grain size of final product and improve its electrochemical performance compared with nature cooling mode and air quenching mode. The sample synthesized by using water quenching mode is of the highest reversible discharge specific capacity and the best cyclic electrochemical performance, demonstrating the first discharge capacity of 138.1 mA·h/g at 0.1C rate and the total loss of capacity of 3.11% after 20 cycles.

Keywords

Li-ion battery / cathode material / LiFePO₄ / cooling mode / microstructure / electrochemical performance

References

[1] NishiY.. Lithium ion batteries: Past 10 years and the future[J]. J Power Sources, 2001, 100(1/2): 101-106

[2] PadhiA. K., NajundaswamyK. S., GoodenoughJ. B.. Phospho-olivines as positive-electrode materials for rechargeable lithium batteries[J]. J Electrochem Soc, 1997, 144(4): 1188-1194

[3] BauerE. M., BellittoC., PasqualiM., et al.. Versatile synthesis of carbon-rich LiFePO₄ enhancing its electrochemical properties[J]. Electrochem Solid-State Lett, 2004, 7(4): A85-A90

[4] ZaghibK., StriebelK., GuerfiA., et al.. LiFePO₄/polymer/natural graphite: Low cost Li-ion batteries[J]. Electrochimica Acta, 2004, 50(2/3): 263-270

[5] HuangH., YinS. C., NazarL. F.. Approaching theoretical capacity of LiFePO₄ at room temperature at high rates[J]. Electrochem Solid-State Lett, 2001, 4(10): A170-A172

[6] GuerfiA., KanekoM., PetitclercM., et al.. LiFePO₄ water-soluble binder electrode for Li-ion batteries[J]. J Power Sources, 2007, 163(2): 1047-1052

[7] HuG.-r., GaoX.-g., PengZ.-d., et al.. Synthesis of LiFePO₄/C composite electrode with enhanced electrochemical performance[J]. Trans Nonferrous Met Soc China, 2005, 15(4): 795-798

[8] MyungS. T., KomabaS., HirosakiN., et al.. Emulsion drying synthesis of olivine LiFePO₄/C composite and its electrochemical properties as lithium intercalation material[J]. Electrochimica Acta, 2004, 49(24): 4213-4222

[9] HoC. S., WonC., HoJ.. Electrochemical properties of carbon-coated LiFePO₄ cathode using graphite, carbon black, and acetylene black[J]. Electrochimica Acta, 2006, 52(4): 1472-1476

[10] YangS.-f., ZavalijP. Y., WhittingghamM. S.. Hydrothermal synthesis of lithium iron phosphate cathodes[J]. Electrochemistry Commun, 2001, 3(9): 505-508

[11] ParkK. S., KangK. T., LeeS. B., et al.. Synthesis of LiFePO₄ with fine particle by co-precipitation method[J]. Materials Research Bulletin, 2004, 39(12): 1803-1810

[12] YamadaA., ChungS. C., HinokumaK.. Optimized LiFePO₄ for lithium battery cathodes[J]. J Electrochem Soc, 2001, 148(3): A224-A229

[13] ChungS. Y., BlockingJ. T., ChiangY. M.. Electronically conductive phospho-olivines as lithium storage electrodes[J]. Nature Mater, 2002, 2: 123-128

[14] HuG.-r., GaoX.-g., PengZ.-d., et al.. Influence of Ti ion doping on electrochemical properties of LiFePO₄/C cathode material for lithium-ion batteries[J]. Trans Nonferrous Met Soc China, 2007, 17(2): 296-300

[15] HongJ., WangC.-s., KasavajjulaU.. Kinetic behavior of LiFeMgPO₄ cathode material for Li-ion batteries[J]. J Power Sources, 2006, 162(2): 1289-1296

[16] WangD.-y., LiH., ShiS.-q., et al.. Improving the rate performance of LiFePO₄ by Fe-site doping[J]. Electrochimica Acta, 2005, 50(14): 2955-2958

[17] RavetN., AbouimraneA., ArmandM., et al.. On the electronic conductivity of phospho-olivines as lithium storage electrodes[J]. Nature Mater, 2003, 2: 702-720

[18] SubramanyaH. P., EllisB., CoombsN., et al.. Nano-network electronic conduction in iron and nickel olivine phosphates[J]. Nature Mater, 2004, 3: 147-152