Dynamic simulation on effect of flame arrangement on thermal process of regenerative reheating furnace

Abstract

By analyzing the characteristics of combustion and billet heating process, a 3-D transient computer fluid dynamic simulation system based on commercial software CFX4.3 and some self-programmed codes were developed to simulate the thermal process in a continuous heating furnace using high temperature air combustion technology. The effects of different switching modes on injection entrancement of multi burners, combustion and billet heating process in furnace were analyzed numerically, and the computational results were compared with on-site measurement, which verified the practicability of this numerical simulation system. The results indicate that the flow pattern and distribution of temperature in regenerative reheating furnace with partial same-side-switching combustion mode are favorable to satisfy the high quality requirements of reheating, in which the terminal heating temperature of billets is more than 1 460 K and the temperature difference between two nodes is not more than 10 K. But since the surface average temperature of billets apart from heating zone is only about 1 350 K and continued heating is needed in soaking zone, the design and operation of current state are still needed to be optimized to improve the temperature schedule of billet heating. The distribution of velocity and temperature in regenerative reheating furnace with same-side-switching combustion mode cannot satisfy the even and fast heating process. The terminal heating temperature of billets is lower than that of the former case by 30 K. The distribution of flow and temperature can be improved by using cross-switching combustion mode, whose terminal temperature of billets is about 1 470 K with small temperature difference within 10 K.

Keywords

high temperature air combustion / reheating furnace / switched combustion / numerical simulation

References

[1] WuZ.-k., YangR., WangJ., et al.. Numerical simulation of a 3-D combustion flow field in a single chamber heating furnace with horizontal tubes[J]. Fire Safety Science, 2001, 10(4): 213-217

[2] ShuZ.-c., ZhuT.. Numerical simulation investigation of the combustion system modification scheme for a cell pit furnace[J]. Journal of Engineering for Thermal Energy & Power, 2003, 18(6): 639-639

[3] ShenB.-z., ZhouJ., HanZ.-q., et al.. Numerical simulation on temperature field of steel slab in reheating furnace of hot rolling process[J]. Metallurgy Energy, 2002, 21(4): 24-28

[4] OuJ.-p., WuD.-h., XiaoZ.-qiang.. Numerical simulation on the flow, combustion and heat transfer in regenerative reheating furnace[J]. Industrial Furnace, 2003, 25(1): 44-47

[5] WuC.-b., LiangX.-p., WangY.. Numerical simulation of flow and heat transfer in impinging heating furnace[J]. Iron and Steel, 1995, 30(3): 58-62

[6] ChenM.-ye.. The numerical value method of metal heating in continuous rolling mill heating furnace[J]. Journal of Shanghai University of Engineering Science, 1995, 9(2): 37-41

[7] ZhangW.-jun.Study of Simulation, Optimization and Intelligence on the Control of Thermal Process for Reheating Furnace[D], 1998, Shenyang, Northeastern University

[8] YangW.-hong.Application of Computational Fluid Dynamics in Industrial Furnace Research and Development[D], 2000, Changsha, Central South University

[9] YutakaS.. Regenerative burner heating system[C]. Proceedings of Beijing Symposium on High Temperature Air Combustion, 1999, Changsha, The Federation of Engineering Societies of Chinese Association for Science and Technology: 170-180

[10] HasegawaT., TanakaR., NiiokaT.. High temperature air combustion contributing to energy saving and pollutant reduction in industrial furnace[C]. Proceedings of Beijing Symposium on High Temperature Air Combustion, 1999, Changsha, The Federation of Engineering Societies of Chinese Association for Science and Technology: 102-114

[11] WangY.-s., FanW.-c., ZhouL.-x., et al.Numerical Computation of Combustion[M], 1986, Changsha, Science Press

[12] TaoW.-quan.Numerical Heat Transfer[M], 1988, Xi’an, Xi’an Jiaotong University Press

[13] AEA Technology Engineering Software Ltd. CFX4.4 User Documentation[M]. Harwell, 1999.

[14] PatankarS. V., ZhangZ. Tr.Numerical Heat Transfer and Fluid Flow[M], 1984, Changsha, Science Press

[15] MeiC.Simulation and Optimization of Nonferrous Metallurgical Furnaces[M], 2001, Changsha, Metallurgical Industry Press

[16] Editorial Committee of References of Industrial Furnace Design for Steel Plant.References of Industrial Furnace Design for Steel Plant (Vol.2)[M], 1979, Changsha, Metallurgical Industry Press