Correlating Cutting Performance and Surface Roughness under Different Bias Using TiAlTaN Coated Milling Tools

Abstract

Driven by the industry’s ongoing pursuit of continuous improvement in machining processes, the need to meet environmental targets, and the limited number of scientific studies addressing coatings doped with Tantalum (Ta), were the main motivations to undertake this investigation. This study investigates the impact of coating cutting tools with a TiAlTaN film deposited at two different bias voltages, −90 V and −135 V, and its relationship with cutting forces, surface roughness, and overall performance when machining AISI P20 steel. The choice of AISI P20 steel was deliberate, considering its widespread use in the mould manufacturing industry and the machining challenges posed by its mechanical properties. Throughout the study, during the machining process, the cutting forces in the three axes were measured, as well as the surface roughness of the AISI P20 steel after machining. A correlation was made between the cutting forces obtained and the roughness of the machined surface, considering the coated tools using bias of −90 V and −135 V. The results show that increasing bias level during the coating deposition has a positive effect on the tool machining performance. Also, there was a correlation between the cutting forces during the machining process and the surface roughness of the machined AISI P20 steel. The coated tool with −135 V bias induced lower cutting forces, in line with the lower roughness shown on the machined surface, when compared to the coated tool with −90 V bias.

Keywords

bias voltage / coated tools / TiAlTaN / tool wear / AISI P20 steel / milling / hard coatings / surface roughness / sustainable manufacturing

References

[1] Schubert M.; Perfetto S.; Dafnis A.; et al. Multifunctional Load Carrying Lightweight Structures for Space Design; Deutsche Gesellschaft für Luft-und Raumfahrt: Bonn, Germany, 2017.

[2] Stampone B.; Pulcini V.; Vitale G.; et al. Towards Industry 5.0 within Micro-Injection moulding Production and Industrialisation: A proof of concept. Procedia Comput. Sci. 2025, 253, 3007-3014.

[3] Farooque R.; Asjad M.; Rizvi S.J.A. A current state of art applied to injection moulding manufacturing process—A review. Mater. Today Proc. 2021, 43, 441-446.

[4] Párizs R.D.; Török D.; Ageyeva T.; et al. Machine Learning in Injection Molding: An Industry 4.0 Method of Quality Prediction. Sensors 2022, 22, 2704.

[5] Silva B.; Marques R.; Faustino D.; et al. Enhance the Injection Molding Quality Prediction with Artificial Intelligence to Reach Zero-Defect Manufacturing. Processes 2023, 11, 62.

[6] Pozzi R.; Rossi T.; Secchi R. Industry 4.0 technologies: critical success factors for implementation and improvements in manufacturing companies. Prod. Plan. Control. 2023, 34, 139-158.

[7] Baptista A.; Silva F.; Porteiro J.; et al. Sputtering Physical Vapour Deposition (PVD) Coatings: A Critical Review on Process Improvement and Market Trend Demands. Coatings 2018, 8, 402.

[8] Baptista A.; Porteiro J.; Míguez J.L.; et al. On the Physical Vapour Deposition (PVD): Evolution of Magnetron Sputtering Processes for Industrial Applications. Procedia Manuf. 2018, 17, 746-757.

[9] Çalışkan H.; Küçükköse M. The effect of aCN/TiAlN coating on tool wear, cutting force, surface finish and chip morphology in face milling of Ti6Al4V superalloy. Int. J. Refract. Met. Hard Mater. 2015, 50, 304-312.

[10] Bouzakis A.; Skordaris G.; Bouzakis E.; et al. Wear Evolution on PVD Coated Cutting Tool Flank and Rake Explained Considering Stress, Strain and Strain-Rate Dependent Material Properties. Coatings 2023, 1982, 13.

[11] Sousa V.F.C.; Da Silva F.J.G.; Pinto G.F.; et al. Characteristics and Wear Mechanisms of TiAlN-Based Coatings for Machining Applications: A Comprehensive Review. Metals 2021, 11, 260.

[12] Girisken I.; Cam G. Characterization of microstructure and high-temperature wear behavior of pack-borided Co-based Haynes 25 superalloy. CIRP J. Manuf. Sci. Technol. 2023, 45, 82-98. https://doi.org/10.1016/j.cirpj.2023.06.012.

[13] Gunen A.; Gurol U.; Kocak M.; et al. Investigation into the influence of boronizing on the wear behavior of additively manufactured Inconel 625 alloy at elevated temperature. Prog. Addit. Manuf. 2023, 8, 1281-1301. https://doi.org/10.1007/s40964-023-00398-8.

[14] Gunen A.; Gurol U.; Kocak M.; et al. A new approach to improve some properties of wire arc additively manufactured stainless steel components: Simultaneous homogenization and boriding. Surf. Coat. Technol. 2023, 460, 129395. https://doi.org/10.1016/j.surfcoat.2023.129395.

[15] Kocaman E.; Gurol U.; Gunen A.; et al. Effect of post-deposition heat treatments on high-temperature wear and corrosion behavior of Inconel 625. Mater. Today Commun. 2025, 42, 111101. https://doi.org/10.1016/j.mtcomm.2024.111101.

[16] Cam G.; Gunen A. Challenges and opportunities in the production of magnesium parts by directed energy deposition processes. J. Magnes. Alloys 2024, 12, 1663-1686. https://doi.org/10.1016/j.jma.2024.05.004.

[17] Bejaxhin A.B.H.; Paulraj G. A Review on Effect of Coatings on Tools and Surface Roughness as Vibration Resistance. Int. J. Emerg. Technol. Eng. Res. 2017, 5, 50-57.

[18] Saruhan H.; Yıldız M. Experimental Vibration Analysis of Titanium Aluminum Nitride (TiAlN) Coated Milling Cutting Tool Effects on Surface Roughness of AISI 4140 Steel Products. Duzce Univ. J. Sci. Technol. 2018, 6, 745-753.

[19] Sousa V.F.C.; Silva F.J.G.; Alexandre R.; et al. Study of the wear behaviour of TiAlSiN and TiAlN PVD coated tools on milling operations of pre-hardened tool steel. Wear 2021, 476, 203695.

[20] Alhafian M.R.; Valle N.; Chemin J.B.; et al. Influence of Si addition on the phase structure and oxidation behavior of PVD AlTiN and AlTiCrN coatings using high-resolution characterization techniques. J. Alloys Compd. 2023, 968, 171800.

[21] Fang C.; Zhang C.; Zhu S.; et al. The influence of Y additions on the microstructure and mechanical properties of MoTaWNb refractory high entropy alloy films by magnetron sputtering. Surf. Coat. Technol. 2024, 484, 130792.

[22] Gordon S.; Rodriguez-Suarez T.; Roa J.J.; et al. Mechanical integrity of PVD TiAlN-coated PcBN: Influence of substrate bias voltage and microstructural assemblage. Ceram. Int. 2024, 50, 6299-6308.

[23] Yang W.; Xiong J.; Guo Z.; et al. Structure and properties of PVD TiAlN and TiAlN/CrAlN coated Ti(C, N)-based cermets. Ceram. Int. 2017, 43, 1911-1915.

[24] Aninat R.; Valle N.; Chemin J.B.; et al. Addition of Ta and Y in a hard Ti-Al-N PVD coating: Individual and conjugated effect on the oxidation and wear properties. Corros. Sci. 2019, 156, 171-180.

[25] Abbas A.T.; Sharma N.; Alsuhaibani Z.A.; et al. Multi-Objective Optimization of AISI P20 Mold Steel Machining in Dry Conditions Using Machine Learning. Machines 2023, 11, 748.

[26] Baptista A. Efficiency, Coating Properties, and Machining Performance of Thin Films Deposited Using HiPIMS: An Experimental Analysis. Ph.D. Thesis, University of Vigo, Vigo, Spain, 2024, https://doi.org/10.35869/11093/8887.

[27] Pinto G.F. Experimental Study on PVD DC Sputtering Thin Films: Efficiency, Coating Properties, and Wear Tools Performance on Milling Pre-Hardness Tools Steels. Ph.D. Thesis, University of Vigo, Vigo, Spain, 2024, https://doi.org/10.35869/11093/8885.

[28] Dias N.F.L.; Meijer A.L.; Biermann D.; et al. Structure and mechanical properties of TiAlTaN thin films deposited by dcMS, HiPIMS, and hybrid dcMS/HiPIMS. Surf. Coat. Technol. 2024, 487, 130987.

[29] Pfeiler M.; Fontalvo G.A.; Wagner J.; et al. Arc Evaporation of Ti-Al-Ta-N Coatings: The Effect of Bias Voltage and Ta on High-temperature Tribological Properties. Tribol. Lett. 2008, 30, 91-97.

[30] Cao H.-S.; Liu F.-J.; Li H.; et al. Effect of bias voltage on microstructure, mechanical and tribological properties of TiAlN coatings. Trans. Nonferrous Met. Soc. China 2022, 32, 3596-3609.

[31] Sui X.; Li G.; Jiang C.; et al. Effect of Ta content on microstructure, hardness and oxidation resistance of TiAlTaN coatings. Int. J. Refract. Met. Hard Mater. 2016, 58, 152-156.

[32] Sun X.; Liu Z.R.; Chen L. Influence of Si and Ta mixed doping on the structure, mechanical and thermal properties of TiAlN coatings. Surf. Coat. Technol. 2023, 461, 129428.

[33] Liu X.; Zhang H.; Liu C.; et al. Influence of bias patterns on the tribological properties of highly hydrogenated PVD a-C:H films. Surf. Coat. Technol. 2022, 442, 128234.

[34] Elmkhah H.; Zhang T.F.; Abdollah-zadeh A.; et al. Surface characteristics for the TiAlN coatings deposited by high power impulse magnetron sputtering technique at the different bias voltages. J. Alloys Compd. 2016, 688, 820-827.

[35] Zhao B.; Zhao X.; Lin L.; et al. Effect of bias voltage on mechanical properties, milling performance and thermal crack propagation of cathodic arc ion-plated TiAlN coatings. Thin Solid Film. 2020, 708, 138116.

[36] ISO 4288: 1996; Geometrical Product Specifications (GPS)—Surface Texture: Profile Method—Rules and Procedures for the Assessment of Surface Texture. International Organization for Standardization: Geneva, Switzerland, 1996.

[37] ISO 8688-2: 1989; Tool Life Testing in Milling—Part 2:End Milling. International Organization for Standardization: Geneva, Switzerland, 1989.

[38] Tillmann W.; Meijer A.L.; Platt T.; et al. Cutting performance of TiAlN-based thin films in micromilling high-speed steel AISI M3:2. Manuf. Lett. 2024, 40, 6-10. https://doi.org/10.1016/j.mfglet.2024.01.005.