Residual Stress Characteristics in Additive/Subtractive Hybrid Manufacturing: A Review

Abstract

This review methodically expounds on the genesis, distribution characteristics, and control methodologies of residual stress (RS) in additive/subtractive hybrid manufacturing (A/SHM). RS, originating from non-uniform temperature fields during manufacturing, rapid solidification of the molten pool, and complex thermal cycling, are key factors causing component deformation, performance degradation, and even cracking. It is evident that significant limitations are imposed on the industrial implementation of A/SHM technology in the domain of high-end equipment manufacturing. This review methodically unveils the influence patterns of process conditions, such as scanning strategies and laser parameters, on RS distribution. It elucidates the intrinsic relationship between microstructural evolution and RS and summarizes effective approaches to regulating RS through process optimization, post-heat treatment, and material modification. This paper proactively proposes a development direction for precise RS regulation through intelligent monitoring and control. This approach provides a theoretical foundation and technical support to enhance the reliability of A/SHM components and advance their industrial applications.

Keywords

Additive/subtractive hybrid manufacturing / Mechanism of residual stress formation / Residual stress characteristics / Microstructure

References

[1] Khan S, Al Rashid A, Muhammad J, Ali F, Koç M. 3D Printing Technology for Rapid Response to Climate Change: Challenges and Emergency Needs. Intell. Sustain. Manuf. 2024, 1, 10004. DOI: 10.35534/ism.2024.10004

[2] Li Z, Qu S, Sun Y, Gong Y, Chu D, Yao P, et al. Robot Grinding: From Frontier Hotspots to Key Technologies and Applications. Intell. Sustain. Manuf. 2025, 2, 10027. DOI: 10.70322/ism.2025.10027

[3] Yang Y, Zong J, Qu S, Xiao G, Xu C. Effects of interlayer milling on the interfacial characteristics and mechanical properties of 316 L/IN718 functionally graded materials. J. Mater. Process. Technol. 2026, 354, 119384. DOI: 10.1016/j.jmatprotec.2026.119384

[4] Qian C, Zhang Y, Liu Y, Wang Z. A cloud service platform integrating additive and subtractive manufacturing with high resource efficiency. J. Clean. Prod. 2019, 241, 118379. DOI: 10.1016/j.jclepro.2019.118379

[5] Ibhadode O, Zhang Z, Sixt J, Nsiempba K, Orakwe J, Martinez-Marchese A, et al. Topology optimization for metal additive manufacturing: Current trends, challenges, and future outlook. Virtual Phys. Prototyp. 2023, 18, e2181192. DOI: 10.1080/17452759.2023.2181192

[6] Popineau V, Célino A, Péron M, Baley C, Le Duigou A. Understanding the effect of hygroscopic cycling on the internal stress and stiffness of natural fibre biocomposites. Compos. Part A Appl. Sci. Manuf. 2022, 158, 106995. DOI: 10.1016/j.compositesa.2022.106995

[7] Lu X, Cervera M, Chiumenti M, Lin X. Residual Stresses Control in Additive Manufacturing. J. Manuf. Mater. Process. 2021, 5, 138. DOI: 10.3390/jmmp5040138

[8] Sebbe N, Fernandes F, Sousa V, Silva F. Hybrid Manufacturing Processes Used in the Production of Complex Parts: A Comprehensive Review. Metals 2022, 12, 1874. DOI: 10.3390/met12111874

[9] Dávila J, Neto P, Noritomi P, Coelho R, da Silva J. Hybrid manufacturing: A review of the synergy between directed energy deposition and subtractive processes. Int. J. Adv. Manuf. Technol. 2020, 110, 3377-3390. DOI: 10.1007/s00170-020-06062-7

[10] Stavropoulos P, Bikas H, Avram O, Valente A, Chryssolouris G. Hybrid subtractive-additive manufacturing processes for high value-added metal components. Int. J. Adv. Manuf. Technol. 2020, 111, 645-655. DOI: 10.1007/s00170-020-06099-8

[11] Yeung H, Lane B, Fox J. Part geometry and conduction-based laser power control for powder bed fusion additive manufacturing. Addit. Manuf. 2019, 30, 100844. DOI: 10.1016/j.addma.2019.100844

[12] Chen C, Xiao Z, Zhang W, Wang Y, Zhu H. Effect of laser jump speed on temperature distribution and thermal stress in laser powder bed fusion. Opt. Laser Technol. 2021, 142, 107275. DOI: 10.1016/j.optlastec.2021.107275

[13] Sun J, Gu D, Lin K, Yuan L, Sun J, Wang R, et al. Laser additive manufacturing of a novel NiTi doubly periodic continuous surface for dispersing in-plane stresses and improving thermo-mechanical protection. Addit. Manuf. 2025, 98, 104643. DOI: 10.1016/j.addma.2025.104643

[14] Qu S, Li L, Yang Y, Sun Y, Pang S, Yin G, et al. Surface roughness and damage evaluation of carbon fiber reinforced silicon carbide composites after laser ablation treatment and subsequent grinding. J. Eur. Ceram. Soc. 2026, 46, 118082. DOI: 10.1016/j.jeurceramsoc.2025.118082.

[15] Parlevliet P, Bersee H, Beukers A. Residual stresses in thermoplastic composites-A study of the literature-Part I: Formation of residual stresses. Compos. Part A Appl. Sci. Manuf. 2006, 37, 1847-1857. DOI: 10.1016/j.compositesa.2005.12.025

[16] Bruggeman K, Klingbeil N, Palazotto A. Residual Stress Generation in Additive Manufacturing of Complex Lattice Geometries. J. Mater. Eng. Perform. 2024, 33, 4088-4105. DOI: 10.1007/s11665-024-09229-5

[17] Li P, Gong Y, Wen X, Xin B, Liu Y, Qu S. Surface residual stresses in additive/subtractive manufacturing and electrochemical corrosion. Int. J. Adv. Manuf. Technol. 2018, 98, 687-697. DOI: 10.1007/s00170-018-2283-4

[18] Parry L, Ashcroft I, Wildman R. Understanding the effect of laser scan strategy on residual stress in selective laser melting through thermo-mechanical simulation. Addit. Manuf. 2016, 12, 1-15. DOI: 10.1016/j.addma.2016.05.014

[19] Guo J, Fu H, Pan B, Kang R. Recent progress of residual stress measurement methods: A review. Chin. J. Aeronaut. 2021, 34, 54-78. DOI: 10.1016/j.cja.2019.10.010

[20] Li C, Liu Z, Fang X, Guo Y. Residual Stress in Metal Additive Manufacturing. Procedia CIRP 2018, 71, 348-353. DOI: 10.1016/j.procir.2018.05.039

[21] Bartlett J, Li X. An overview of residual stresses in metal powder bed fusion. Addit. Manuf. 2019, 27, 131-149. DOI: 10.1016/j.addma.2019.02.020

[22] Qu S, Yao P, Gong Y, Yang Y, Chu D, Zhu Q. Modelling and grinding characteristics of unidirectional C-SiCs. Ceramics International. 2022, 48, 8314-8324. DOI: 10.1016/j.ceramint.2021.12.036.

[23] Sun C, He P, Hu Z, Liang X. Metallurgical Characteristics of 316L Stainless Steel by Laser Additive Manufacturing. Intell. Sustain. Manuf. 2024, 1, 10012. DOI: 10.35534/ism.2024.10012.

[24] Fang Z, Wu Z, Huang C, Wu C. Review on residual stress in selective laser melting additive manufacturing of alloy parts. Opt. Laser Technol. 2020, 129, 106283. DOI: 10.1016/j.optlastec.2020.106283

[25] Liu C, Lin C, Wang J, Wang J, Yan L, Luo Y, et al. Residual stress distributions in thick specimens excavated from a large circular wire+arc additive manufacturing mockup. J. Manuf. Process. 2020, 56, 474-481. DOI: 10.1016/j.jmapro.2020.05.007

[26] Mercelis P, Kruth J. Residual stresses in selective laser sintering and selective laser melting. Rapid Prototyp. J. 2006, 12, 254-265. DOI: 10.1108/13552540610707013

[27] Wang C. Simultaneous optimization of build orientation and topology for self-supported enclosed voids in additive manufacturing. Comput. Methods Appl. Mech. Eng. 2022, 388, 114227. DOI: 10.1016/j.cma.2021.114227

[28] Johnson T, Gaynor A. Three-dimensional projection-based topology optimization for prescribed-angle self-supporting additively manufactured structures. Addit. Manuf. 2018, 24, 667-686. DOI: 10.1016/j.addma.2018.06.011

[29] Campanelli S, Carone S, Casavola K, Errico V, Pappalettera G, Posa P. Residual stress evaluation in innovative layer-level continuous functionally graded materials produced by Powder Bed Fusion-Laser Beam. Int. J. Adv. Manuf. Technol. 2024, 134, 511-527. DOI: 10.1007/s00170-024-14148-9

[30] Yang S, Clare A, Jin X. Understanding residual stress in functionally graded directed energy deposition. Addit. Manuf. 2024, 96, 104581. DOI: 10.1016/j.addma.2024.104581

[31] Hafenecker J, Bartels D, Kuball C, Kreß M, Rothfelder R, Schmidt M, et al. Hybrid process chains combining metal additive manufacturing and forming-A review. CIRP J. Manuf. Sci. Technol. 2023, 46, 98-115. DOI: 10.1016/j.cirpj.2023.08.002

[32] Guo Y, Lu N, Yang Y, Liang J, Zhang G, Jia W, et al. Regulation of annealing treatment for lowering residual stress and avoiding recrystallization in directed energy deposition-repaired single-crystal superalloys. Mater. Charact. 2025, 228, 115382. DOI: 10.1016/j.matchar.2025.115382

[33] Zhao J, Wang X, Yang Q, Wang Q, Wang Y, Li W. Mechanism of lateral metal flow on residual stress distribution during hot strip rolling. J. Mater. Process. Technol. 2021, 288, 116838. DOI: 10.1016/j.jmatprotec.2020.116838

[34] Liu Y, Shi J, Wang Y. Evolution, Control, and Mitigation of Residual Stresses in Additively Manufactured Metallic Materials: A Review. Adv. Eng. Mater. 2023, 25, 2300489. DOI: 10.1002/adem.202300489

[35] Maleki E, Unal O, Guagliano M, Bagherifard S. The effects of shot peening, laser shock peening and ultrasonic nanocrystal surface modification on the fatigue strength of Inconel 718. Mater. Sci. Eng. A 2021, 810, 141029. DOI: 10.1016/j.msea.2021.141029

[36] Madireddy G, Feldhausen T, Kannan R, Nandwana P, MacDonald E, Love L, et al. Effect of additive and subtractive sequence on the distortion of cone-shaped part during hybrid direct energy deposition. J. Manuf. Process. 2024, 119, 146-155. DOI: 10.1016/j.jmapro.2024.03.080

[37] Chen S, Gao H, Zhang Y, Wu Q, Gao Z, Zhou X. Review on residual stresses in metal additive manufacturing: Formation mechanisms, parameter dependencies, prediction and control approaches. J. Mater. Res. Technol. 2022, 17, 2950-2974. DOI: 10.1016/j.jmrt.2022.02.054

[38] Liu W, Shen S, Meng J, Xiao J, Li H, Du H, et al. Mechanical field assisted additive manufacturing of ultrahigh strength aluminum alloy. Int. J. Extrem. Manuf. 2025, 7, 045008. DOI: 10.1088/2631-7990/adbb95

[39] Zhan Y, Xu H, Du W, Liu C. Research on the influence of heat treatment on residual stress of TC4 alloy produced by laser additive manufacturing based on laser ultrasonic technique. Ultrasonics 2021, 115, 106466. DOI: 10.1016/j.ultras.2021.106466

[40] Tonelli L, Liverani E, Morri A, Ceschini L. Role of Direct Aging and Solution Treatment on Hardness, Microstructure and Residual Stress of the A357 (AlSi7Mg0.6) Alloy Produced by Powder Bed Fusion. Met. Mater. Trans. B 2021, 52, 2484-2496. DOI: 10.1007/s11663-021-02179-6

[41] Dixit T, Al-Hajri E, Paul M, Nithiarasu P, Kumar S. High performance, microarchitected, compact heat exchanger enabled by 3D printing. Appl. Therm. Eng. 2022, 210, 118339. DOI: 10.1016/j.applthermaleng.2022.118339

[42] Feppon F, Allaire G, Dapogny C, Jolivet P. Body-fitted topology optimization of 2D and 3D fluid-to-fluid heat exchangers. Comput. Methods Appl. Mech. Eng. 2021, 376, 113638. DOI: 10.1016/j.cma.2020.113638

[43] Swesi S, Yousfi M, Tardif N, Banoune A. Process Parameters Optimization and Mechanical Properties of Additively Manufactured Ankle-Foot Orthoses Based on Polypropylene. Polymers 2025, 17, 1921. DOI: 10.3390/polym17141921

[44] Sun G, Zhang H, Wang R, Lv X, Li Q. Multiobjective reliability-based optimization for crashworthy structures coupled with metal forming process. Struct. Multidisc Optim. 2017, 56, 1571-1587. DOI: 10.1007/s00158-017-1825-y

[45] Gao W, Zhang Y, Ramanujan D, Ramani K, Chen Y, Williams C, et al. The status, challenges, and future of additive manufacturing in engineering. Comput.-Aided Des. 2015, 69, 65-89. DOI: 10.1016/j.cad.2015.04.001

[46] Armstrong M, Mehrabi H, Naveed N. An overview of modern metal additive manufacturing technology. J. Manuf. Process. 2022, 84, 1001-1029. DOI: 10.1016/j.jmapro.2022.10.060

[47] Zhang Y, Wu L, Guo X, Kane S, Deng Y, Jung Y, et al. Additive Manufacturing of Metallic Materials: A Review. J. Mater. Eng. Perform. 2018, 27, 1-13. DOI: 10.1007/s11665-017-2747-y

[48] Ngo T, Kashani A, Imbalzano G, Nguyen K, Hui D. Additive manufacturing (3D printing): A review of materials, methods, applications and challenges. Compos. Part B Eng. 2018, 143, 172-196. DOI: 10.1016/j.compositesb.2018.02.012

[49] Herzog D, Seyda V, Wycisk E, Emmelmann C. Additive manufacturing of metals. Acta Mater. 2016, 117, 371-392. DOI: 10.1016/j.actamat.2016.07.019

[50] Sanaei N, Fatemi A. Defects in additive manufactured metals and their effect on fatigue performance: A state-of-the-art review. Prog. Mater. Sci. 2021, 117, 100724. DOI: 10.1016/j.pmatsci.2020.100724

[51] Narasimharaju S, Zeng W, See T, Zhu Z, Scott P, Jiang X, et al. A comprehensive review on laser powder bed fusion of steels: Processing, microstructure, defects and control methods, mechanical properties, current challenges and future trends. J. Manuf. Process. 2022, 75, 375-414. DOI: 10.1016/j.jmapro.2021.12.033

[52] Kurose T, Abe Y, Santos M, Kanaya Y, Ishigami A, Tanaka S, et al. Influence of the Layer Directions on the Properties of 316L Stainless Steel Parts Fabricated through Fused Deposition of Metals. Materials 2020, 13, 2493. DOI: 10.3390/ma13112493

[53] Guo C, Li S, Shi S, Li X, Hu X, Zhu Q, et al. Effect of processing parameters on surface roughness, porosity and cracking of as-built IN738LC parts fabricated by laser powder bed fusion. J. Mater. Process. Technol. 2020, 285, 116788. DOI: 10.1016/j.jmatprotec.2020.116788

[54] Fan H, Liu C, Bian S, Ma C, Huang J, Liu X, et al. New era towards autonomous additive manufacturing: A review of recent trends and future perspectives. Int. J. Extrem. Manuf. 2025, 7, 032006. DOI: 10.1088/2631-7990/ada8e4

[55] Ng W, Goh G, Goh G, Ten J, Yeong W. Progress and Opportunities for Machine Learning in Materials and Processes of Additive Manufacturing. Adv. Mater. 2024, 36, 2310006. DOI: 10.1002/adma.202310006

[56] Wang T, Li Y, Li T, Liu B, Li X, Zhang X. Machine learning in additive manufacturing: Enhancing design, manufacturing and performance prediction intelligence. J. Intell. Manuf. 2026, 37, 711-736. DOI: 10.1007/s10845-025-02568-7

[57] Yu M, Zhu L, Yang Z, Ning J, Xue P, Wang S, et al. Machine learning-assisted process-structure-property correlation in laser metal additive manufacturing: A critical review. Int. J. Extrem. Manuf. 2026, 8, 042005. DOI: 10.1088/2631-7990/ae5297

[58] Hegab H, Khanna N, Monib N, Salem A. Design for sustainable additive manufacturing: A review. Sustain. Mater. Technol. 2023, 35, e00576. DOI: 10.1016/j.susmat.2023.e00576

[59] Kanishka K, Acherjee B. Revolutionizing manufacturing: A comprehensive overview of additive manufacturing processes, materials, developments, and challenges. J. Manuf. Process. 2023, 107, 574-619. DOI: 10.1016/j.jmapro.2023.10.024

[60] Orme M, Gschweitl M, Ferrari M, Vernon R, Madera I, Yancey R, et al. Additive Manufacturing of Lightweight, Optimized, Metallic Components Suitable for Space Flight. J. Spacecr. Rocket. 2017, 54, 1050-1059. DOI: 10.2514/1.A33749

[61] Orme M, Gschweitl M, Ferrari M, Madera I, Mouriaux F. Designing for Additive Manufacturing: Lightweighting Through Topology Optimization Enables Lunar Spacecraft. J. Mech. Des. 2017, 139, 100905. DOI: 10.1115/1.4037304

[62] Khan N, Riccio A. A systematic review of design for additive manufacturing of aerospace lattice structures: Current trends and future directions. Prog. Aerosp. Sci. 2024, 149, 101021. DOI: 10.1016/j.paerosci.2024.101021

[63] Gardner L, Kyvelou P, Herbert G, Buchanan C. Testing and initial verification of the world's first metal 3D printed bridge. J. Constr. Steel Res. 2020, 172, 106233. DOI: 10.1016/j.jcsr.2020.106233

[64] Shum J, Gadomski B, Tredinnick S, Fok W, Fernandez J, Nelson B, et al. Enhanced bone formation in locally-optimised, low-stiffness additive manufactured titanium implants: An in silicoand in vivotibial advancement study. Acta Biomater. 2023, 156, 202-213. DOI: 10.1016/j.actbio.2022.04.006

[65] Li Y, Jiang D, Zhu R, Yang C, Wang L, Zhang L. Revolutionizing medical implant fabrication: Advances in additive manufacturing of biomedical metals. Int. J. Extrem. Manuf. 2025, 7, 022002. DOI: 10.1088/2631-7990/ad92cc

[66] Carter L, Addison O, Naji N, Seres P, Wilman A, Shepherd D, et al. Reducing MRI susceptibility artefacts in implants using additively manufactured porous Ti-6Al-4V structures. Acta Biomater. 2020, 107, 338-348. DOI: 10.1016/j.actbio.2020.02.038

[67] Yadav D, Srivastava R, Dev S. Design & fabrication of ABS part by FDM for automobile application. Mater. Today Proc. 2020, 26, 2089-2093. DOI: 10.1016/j.matpr.2020.02.451

[68] Lyu M, Choi T. Research trends in polymer materials for use in lightweight vehicles. Int. J. Precis. Eng. Manuf. 2015, 16, 213-220. DOI: 10.1007/s12541-015-0029-x

[69] Gao T, Zhang Y, Li C, Wang Y, Chen Y, An Q, et al. Fiber-reinforced composites in milling and grinding: Machining bottlenecks and advanced strategies. Front. Mech. Eng. 2022, 17, 24. DOI: 10.1007/s11465-022-0680-8

[70] Zhu Z, Tang X, Chen C, Peng F, Yan R, Zhou L, et al. High precision and efficiency robotic milling of complex parts: Challenges, approaches and trends. Chin. J. Aeronaut. 2022, 35, 22-46. DOI: 10.1016/j.cja.2020.12.030

[71] Li Z, Chen Y, Li H, Ju B. Force servo nano-precision diamond cutting of freeform surfaces on a micro-precision machine. J. Mater. Process. Technol. 2024, 325, 118283. DOI: 10.1016/j.jmatprotec.2024.118283

[72] Chen Z, Ding F, Zhang Z, Liao Q, Qiao Z, Jin Y, et al. A Review on Machining SiCp/Al Composite Materials. Micromachines 2024, 15, 107. DOI: 10.3390/mi15010107

[73] Liu X, Li Y, Zeng L, Li X, Chen N, Bai S, et al. A Review on Mechanochemistry: Approaching Advanced Energy Materials with Greener Force. Adv. Mater. 2022, 34, 2108327. DOI: 10.1002/adma.202108327

[74] Luo H, Zhang Y, Yu J, Dong X, Zhou T. Additive, subtractive and formative manufacturing of glass-based functional micro/nanostructures: A comprehensive review. Mater. Des. 2023, 233, 112285. DOI: 10.1016/j.matdes.2023.112285

[75] Touzé S, Rauch M, Hascoët J. Methodology for complexity and cost comparison between subtractive and additive manufacturing processes. J. Intell. Manuf. 2024, 35, 555-574. DOI: 10.1007/s10845-022-02059-z

[76] Wang X, Song Y, Li C, Zhang Y, Ali H, Sharma S, et al. Nanofluids application in machining: A comprehensive review. Int. J. Adv. Manuf. Technol. 2024, 131, 3113-3164. DOI: 10.1007/s00170-022-10767-2

[77] Gavalda D, Axinte D. Towards understanding the cutting and fracture mechanism in Ceramic Matrix Composites. Int. J. Mach. Tools Manuf. 2017, 118-119, 12-25. DOI: 10.1016/j.ijmachtools.2017.03.008

[78] Liu Q, Huang G, Xu X, Fang C, Cui C. Influence of grinding fiber angles on grinding of the 2D-Cf/C-SiC composites. Ceram. Int. 2018, 44, 12774-12782. DOI: 10.1016/j.ceramint.2018.04.083

[79] Luo W, Hu T, Zhang C, Wei Y. Digital twin for CNC machine tool: Modeling and using strategy. J. Ambient. Intell. Hum. Comput. 2019, 10, 1129-1140. DOI: 10.1007/s12652-018-0946-5

[80] Yao R, Pang T, Zhang B, Fang J, Li Q, Sun G. On the crashworthiness of thin-walled multi-cell structures and materials: State of the art and prospects. Thin-Walled Struct. 2023, 189, 110734. DOI: 10.1016/j.tws.2023.110734

[81] Chen Y, Zhang J, Li Z, Zhang H, Chen J, Yang W, et al. Manufacturing Technology of Lightweight Fiber-Reinforced Composite Structures in Aerospace: Current Situation and toward Intellectualization. Aerospace 2023, 10, 206. DOI: 10.3390/aerospace10030206

[82] Redmann A, Montoya-Ospina M, Karl R, Rudolph N, Osswald T. High-force dynamic mechanical analysis of composite sandwich panels for aerospace structures. Compos. Part C Open Access 2021, 5, 100136. DOI: 10.1016/j.jcomc.2021.100136

[83] Kausar A, Ahmad I, Rakha S, Eisa M, Diallo A. State-Of-The-Art of Sandwich Composite Structures: Manufacturing-to-High Performance Applications. J. Compos. Sci. 2023, 7, 102. DOI: 10.3390/jcs7030102

[84] da Silva L, Sales W, Campos F, de Sousa J, Davis R, Singh A, et al. A comprehensive review on additive manufacturing of medical devices. Prog. Addit. Manuf. 2021, 6, 517-553. DOI: 10.1007/s40964-021-00188-0

[85] Davis R, Singh A, Jackson M, Coelho R, Prakash D, Charalambous C, et al. A comprehensive review on metallic implant biomaterials and their subtractive manufacturing. Int. J. Adv. Manuf. Technol. 2022, 120, 1473-1530. DOI: 10.1007/s00170-022-08770-8

[86] Shah V, Bhaliya J, Patel G, Deshmukh K. Advances in polymeric nanocomposites for automotive applications: A review. Polym. Adv. Technol. 2022, 33, 3023-3048. DOI: 10.1002/pat.5771

[87] de Leon M, Shin H. Review of the advancements in aluminum and copper ultrasonic welding in electric vehicles and superconductor applications. J. Mater. Process. Technol. 2022, 307, 117691. DOI: 10.1016/j.jmatprotec.2022.117691

[88] Li L, Haghighi A, Yang Y. A novel 6-axis hybrid additive-subtractive manufacturing process: Design and case studies. J. Manuf. Process. 2018, 33, 150-160. DOI: 10.1016/j.jmapro.2018.05.008

[89] Du W, Bai Q, Zhang B. A Novel Method for Additive/Subtractive Hybrid Manufacturing of Metallic Parts. Procedia Manuf. 2016, 5, 1018-1030. DOI: 10.1016/j.promfg.2016.08.067

[90] Manogharan G, Wysk R, Harrysson O, Aman R. AIMS-A Metal Additive-hybrid Manufacturing System: System Architecture and Attributes. Procedia Manuf. 2015, 1, 273-286. DOI: 10.1016/j.promfg.2015.09.021

[91] Flynn J, Shokrani A, Newman S, Dhokia V. Hybrid additive and subtractive machine tools-Research and industrial developments. Int. J. Mach. Tools Manuf. 2016, 101, 79-101. DOI: 10.1016/j.ijmachtools.2015.11.007

[92] Feldhausen T, Heinrich L, Saleeby K, Burl A, Post B, MacDonald E, et al. Review of Computer-Aided Manufacturing (CAM) strategies for hybrid directed energy deposition. Addit. Manuf. 2022, 56, 102900. DOI: 10.1016/j.addma.2022.102900

[93] Dilberoglu U, Gharehpapagh B, Yaman U, Dolen M. Current trends and research opportunities in hybrid additive manufacturing. Int. J. Adv. Manuf. Technol. 2021, 113, 623-648. DOI: 10.1007/s00170-021-06688-1

[94] Du W, Bai Q, Zhang B. Machining characteristics of 18Ni-300 steel in additive/subtractive hybrid manufacturing. Int. J. Adv. Manuf. Technol. 2018, 95, 2509-2519. DOI: 10.1007/s00170-017-1364-0

[95] Ambrogio G, Gagliardi F, Muzzupappa M, Filice L. Additive-incremental forming hybrid manufacturing technique to improve customised part performance. J. Manuf. Process. 2019, 37, 386-391. DOI: 10.1016/j.jmapro.2018.12.008

[96] Behandish M, Nelaturi S, de Kleer J. Automated process planning for hybrid manufacturing. Comput.-Aided Des. 2018, 102, 115-127. DOI: 10.1016/j.cad.2018.04.022

[97] Liu Z, Zhao Y, Wang Q, Xing H, Sun J. Modeling and Assessment of Carbon Emissions in Additive-Subtractive Integrated Hybrid Manufacturing Based on Energy and Material Analysis. Int. J. Precis. Eng. Manuf.-Green Technol. 2024, 11, 799-813. DOI: 10.1007/s40684-023-00588-3

[98] Merklein M, Junker D, Schaub A, Neubauer F. Hybrid Additive Manufacturing Technologies-An Analysis Regarding Potentials and Applications. Phys. Procedia 2016, 83, 549-559. DOI: 10.1016/j.phpro.2016.08.057

[99] Chu W, Kim C, Lee H, Choi J, Park J, Song J, et al. Hybrid manufacturing in micro/nano scale: A Review. Int. J. Precis. Eng. Manuf.-Green Technol. 2014, 1, 75-92. DOI: 10.1007/s40684-014-0012-5

[100] Zhu Z, Dhokia V, Nassehi A, Newman S. A review of hybrid manufacturing processes-State of the art and future perspectives. Int. J. Comput. Integr. Manuf. 2013, 26, 596-615. DOI: 10.1080/0951192X.2012.749530

[101] Lalegani Dezaki M, Serjouei A, Zolfagharian A, Fotouhi M, Moradi M, Ariffin M, et al. A review on additive/subtractive hybrid manufacturing of directed energy deposition (DED) process. Adv. Powder Mater. 2022, 1, 100054. DOI: 10.1016/j.apmate.2022.100054

[102] Khorasani M, Gibson I, Ghasemi A, Hadavi E, Rolfe B. Laser subtractive and laser powder bed fusion of metals: Review of process and production features. Rapid Prototyp. J. 2023, 29, 935-958. DOI: 10.1108/RPJ-03-2021-0055

[103] Juhasz M, Tiedemann R, Dumstorff G, Walker J, Plessis A, Conner B, et al. Hybrid directed energy deposition for fabricating metal structures with embedded sensors. Addit. Manuf. 2020, 35, 101397. DOI: 10.1016/j.addma.2020.101397

[104] Cortina M, Arrizubieta J, Ruiz J, Ukar E, Lamikiz A. Latest Developments in Industrial Hybrid Machine Tools that Combine Additive and Subtractive Operations. Materials 2018, 11, 2583. DOI: 10.3390/ma11122583

[105] LASERTEC 65 DED Hybrid-Additive Manufacturing Machines, DMG MORI. Available online: https://en.dmgmori.com/products/machines/additive-manufacturing/powder-nozzle/lasertec-65-ded-hybrid (accessed on 16 January 2026).

[106] Hybrid Metal 3D Printer LUMEX Series, Hybrid Metal 3D Printer LUMEX Series. Available online: https://www.lumex-matsuura.com/english (accessed on 16 January 2026).

[107] OPM250L. Sodick Inc. Available online: https://sodick.com/product/opm250l/ (accessed on 16 January 2026).

[108] Iqbal A, Zhao G, Suhaimi H, He N, Hussain G, Zhao W. Readiness of subtractive and additive manufacturing and their sustainable amalgamation from the perspective of Industry 4.0: A comprehensive review. Int. J. Adv. Manuf. Technol. 2020, 111, 2475-2498. DOI: 10.1007/s00170-020-06287-6

[109] Liu J, To AC. Topology optimization for hybrid additive-subtractive manufacturing. Struct. Multidisc Optim. 2017, 55, 1281-1299. DOI: 10.1007/s00158-016-1565-4

[110] Yue W, Zhang Y, Zheng Z, Lai Y. Hybrid Laser Additive Manufacturing of Metals: A Review. Coatings 2024, 14, 315. DOI: 10.3390/coatings14030315

[111] Liu W, Deng K, Wei H, Zhao P, Li J, Zhang Y. A decision-making model for comparing the energy demand of additive-subtractive hybrid manufacturing and conventional subtractive manufacturing based on life cycle method. J. Clean. Prod. 2021, 311, 127795. DOI: 10.1016/j.jclepro.2021.127795

[112] Parlevliet P, Bersee H, Beukers A. Residual stresses in thermoplastic composites-A study of the literature-Part II: Experimental techniques. Compos. Part A Appl. Sci. Manuf. 2007, 38, 651-665. DOI: 10.1016/j.compositesa.2006.07.002

[113] Bektas N, Sayman O. Thermal Elastic-Plastic Stress Analysis in Simply Supported Thermoplastic Laminated Plates. J. Reinf. Plast. Compos. 2002, 21, 639-652. DOI: 10.1177/0731684402021007028

[114] Sayman O, Yanginci S, Sayer M. Thermoelastic-Plastic Stress Analysis in a Thermoplastic Composite Disc. J. Reinf. Plast. Compos. 2005, 24, 21-33. DOI: 10.1177/0731684405041716

[115] Safarabadi M. Evaluation of curing residual stresses in three-phase thin composite laminates considering micro-scale effects. J. Compos. Mater. 2016, 50, 3753-3764. DOI: 10.1177/0021998315624252

[116] Huang Z, Su S, Wang X, Chu F. Stress Analysis and Stiffness Degradation of Open Cracks Composite Laminates Subjected to External Loads. Biomimetics 2025, 10, 177. DOI: 10.3390/biomimetics10030177

[117] Lu C, Chen P, Yu Q, Gao J, Yu B. Thermal Residual Stress Distribution in Carbon Fiber/Novel Thermal Plastic Composite. Appl. Compos. Mater. 2008, 15, 157-169. DOI: 10.1007/s10443-008-9064-4

[118] Parlevliet P, Bersee H, Beukers A. Residual stresses in thermoplastic composites-A study of the literature. Part III: Effects of thermal residual stresses. Compos. Part A Appl. Sci. Manuf. 2007, 38, 1581-1596. DOI: 10.1016/j.compositesa.2006.12.005

[119] Sun L, Ren X, He J, Zhang Z. Numerical investigation of a novel pattern for reducing residual stress in metal additive manufacturing. J. Mater. Sci. Technol. 2021, 67, 11-22. DOI: 10.1016/j.jmst.2020.05.080

[120] Song X, Feih S, Zhai W, Sun CN, Li F, Maiti R, et al. Advances in additive manufacturing process simulation: Residual stresses and distortion predictions in complex metallic components. Mater. Des. 2020, 193, 108779. DOI: 10.1016/j.matdes.2020.108779

[121] Gu J, Liang Z, Shi J, Yang Y. Electrochemo‐Mechanical Stresses and Their Measurements in Sulfide‐Based All‐Solid‐State Batteries: A Review. Adv. Energy Mater. 2023, 13, 2203153. DOI: 10.1002/aenm.202203153

[122] Xie B, Li L, Fang Q, Li J, Liu B, Huang Z, et al. Evolution of residual stress and its impact on Ni-based superalloy. Int. J. Mech. Sci. 2021, 202-203, 106494. DOI: 10.1016/j.ijmecsci.2021.106494

[123] Roscow J, Li Y, Hall D. Residual stress and domain switching in freeze cast porous barium titanate. J. Eur. Ceram. Soc. 2022, 42, 1434-1444. DOI: 10.1016/j.jeurceramsoc.2021.11.046

[124] Hemmesi K, Mallet P, Farajian M. Numerical evaluation of surface welding residual stress behavior under multiaxial mechanical loading and experimental validations. Int. J. Mech. Sci. 2020, 168, 105127. DOI: 10.1016/j.ijmecsci.2019.105127

[125] Soori M, Arezoo B. A Review in Machining-Induced Residual Stress. J. New Technol. Mater. 2022, 12, 64-83. Available online: https://hal.science/hal-03679993/ (accessed on 16 January 2026).

[126] Narvan M, Ghasemi A, Fereiduni E, Kendrish S, Elbestawi M. Part deflection and residual stresses in laser powder bed fusion of H13 tool steel. Mater. Des. 2021, 204, 109659. DOI: 10.1016/j.matdes.2021.109659

[127] Tabatabaeian A, Ghasemi AR, Shokrieh M, Marzbanrad B, Baraheni M, Fotouhi M. Residual Stress in Engineering Materials: A Review. Adv. Eng. Mater. 2022, 24, 2100786. DOI: 10.1002/adem.202100786

[128] Wang C, Xiao J, Liu W, Ma Z. Unloading and reloading stress-strain relationship of recycled aggregate concrete reinforced with steel/polypropylene fibers under uniaxial low-cycle loadings. Cem. Concr. Compos. 2022, 131, 104597. DOI: 10.1016/j.cemconcomp.2022.104597

[129] Chen X, Cheng G, Yang J, Hu J, Liao C, Zhang X, et al. Effects of interfacial residual stress on mechanical behavior of SiCf/SiC composites. J. Adv. Ceram. 2022, 11, 94-104. DOI: 10.1007/s40145-021-0519-5

[130] Carpenter K, Tabei A. On Residual Stress Development, Prevention, and Compensation in Metal Additive Manufacturing. Materials 2020, 13, 255. DOI: 10.3390/ma13020255

[131] Uebing S, Brands D, Scheunemann L, Schröder J. Residual stresses in hot bulk formed parts: Microscopic stress analysis for austenite-to-martensite phase transformation. Arch. Appl. Mech. 2021, 91, 3603-3625. DOI: 10.1007/s00419-021-01921-5

[132] Alghamdi A, Alharthi H. Finite Element Simulation of the Effect of Phase Transformation on Residual Stress in a Thick Section T-Joint. Crystals 2022, 12, 1422. DOI: 10.3390/cryst12101422

[133] Villa M, Grumsen F, Pantleon K, Somers M. Martensitic transformation and stress partitioning in a high-carbon steel. Scr. Mater. 2012, 67, 621-624. DOI: 10.1016/j.scriptamat.2012.06.027

[134] Bai Q, Gao Y, Wu B, Kang R, Li J, Zhang Y. Solid-state phase transformation-induced residual stress in selective laser melting of martensitic stainless steel. Int. J. Adv. Manuf. Technol. 2022, 120, 6747-6760. DOI: 10.1007/s00170-022-09139-7

[135] Afzal M, Maqbool F, Hajavifard R, Buhl J, Walther F, Bambach M. Modeling the Residual Stresses Induced in the Metastable Austenitic Stainless Steel Disc Springs manufactured by Incremental Sheet Forming by a Combined Hardening Model with Phase Transformation. Procedia Manuf. 2020, 47, 1410-1415. DOI: 10.1016/j.promfg.2020.04.300

[136] Li X, Ju D, Cao J, Wang S, Chen Y, He F, et al. Effect of Transformation Plasticity on Gear Distortion and Residual Stresses in Carburizing Quenching Simulation. Coatings 2021, 11, 1224. DOI: 10.3390/coatings11101224

[137] Ni J, Zhuang X, Abdel Wahab M. Review on The Prediction of Residual Stress in Welded Steel Components. Comput. Mater. Contin. 2020, 62, 495-523. DOI: 10.32604/cmc.2020.08448

[138] Ding Z, Sun G, Guo M, Jiang X, Li B, Liang S. Effect of phase transition on micro-grinding-induced residual stress. J. Mater. Process. Technol. 2020, 281, 116647. DOI: 10.1016/j.jmatprotec.2020.116647

[139] Sun C, Yang M, Li H, Hui P, Ruan Y, Wei B. Dislocation motion and strengthening mechanism of Ti-Al-Mo-Si alloy with multiple interlaced phases. Mater. Sci. Eng. A 2025, 938, 148423. DOI: 10.1016/j.msea.2025.148423

[140] Luo H, Sun X, Xu L, He W, Liang X. A review on stress determination and control in metal-based additive manufacturing. Theor. Appl. Mech. Lett. 2023, 13, 100396. DOI: 10.1016/j.taml.2022.100396

[141] Zhang X, Dong M, Cai X, Chen D, Xian Y, Zheng X, et al. Progress in machining-induced residual stress and microstructural evolution of inhomogeneous materials and composites. Adv. Compos. Hybrid. Mater. 2023, 6, 122. DOI: 10.1007/s42114-023-00698-1

[142] Pokharel R, Patra A, Brown D, Clausen B, Vogel S, Gray G. An analysis of phase stresses in additively manufactured 304L stainless steel using neutron diffraction measurements and crystal plasticity finite element simulations. Int. J. Plast. 2019, 121, 201-217. DOI: 10.1016/j.ijplas.2019.06.005

[143] Bouafia F, Serier B, Bouiadjra B. Finite element analysis of the thermal residual stresses of SiC particle reinforced aluminum composite. Comput. Mater. Sci. 2012, 54, 195-203. DOI: 10.1016/j.commatsci.2011.10.030

[144] Péron M, Célino A, Castro M, Jacquemin F, Le Duigou A. Study of hygroscopic stresses in asymmetric biocomposite laminates. Compos. Sci. Technol. 2019, 169, 7-15. DOI: 10.1016/j.compscitech.2018.10.027

[145] Zhang J, Hu M, Liu S, Wang L, Gu B, Sun B. High strain rate compressive behaviors and adiabatic shear band localization of 3-D carbon/epoxy angle-interlock woven composites at different loading directions. Compos. Struct. 2019, 211, 502-521. DOI: 10.1016/j.compstruct.2018.12.037

[146] He J, Cui X, Lua J, Liu L. Interplay of manufacturing-induced thermal residual stresses and microvoids in damage and failure of fiber-reinforced composites. Int. J. Mech. Sci. 2023, 242, 108000. DOI: 10.1016/j.ijmecsci.2022.108000

[147] Samuel A, Prabhu K. Residual Stress and Distortion during Quench Hardening of Steels: A Review. J. Mater. Eng. Perform. 2022, 31, 5161-5188. DOI: 10.1007/s11665-022-06667-x

[148] Franceschi A, Stahl J, Kock C, Selbmann R, Ortmann-Ishkina S, Jobst A, et al. Strategies for residual stress adjustment in bulk metal forming. Arch. Appl. Mech. 2021, 91, 3557-3577. DOI: 10.1007/s00419-021-01903-7

[149] Barath Kumar M, Manikandan M. Assessment of Process, Parameters, Residual Stress Mitigation, Post Treatments and Finite Element Analysis Simulations of Wire Arc Additive Manufacturing Technique. Met. Mater. Int. 2022, 28, 54-111. DOI: 10.1007/s12540-021-01015-5

[150] Gurmesa F, Lemu H. Literature Review on Thermomechanical Modelling and Analysis of Residual Stress Effects in Wire Arc Additive Manufacturing. Metals 2023, 13, 526. DOI: 10.3390/met13030526

[151] Zhang D, Du D, Xue S, Qi J, Pu Z, Lu Y, et al. Residual stress and deformation in wire-feed electron beam additive manufactured aluminum components. Int. J. Adv. Manuf. Technol. 2024, 131, 1665-1676. DOI: 10.1007/s00170-024-13169-8

[152] Chen C, Yin J, Zhu H, Xiao Z, Zhang L, Zeng X. Effect of overlap rate and pattern on residual stress in selective laser melting. Int. J. Mach. Tools Manuf. 2019, 145, 103433. DOI: 10.1016/j.ijmachtools.2019.103433

[153] Zhang W, Tong M, Harrison N. Scanning strategies effect on temperature, residual stress and deformation by multi-laser beam powder bed fusion manufacturing. Addit. Manuf. 2020, 36, 101507. DOI: 10.1016/j.addma.2020.101507

[154] Jiang X, Wei Y, Zhou J, Zhan K, Ding Z, Liang S. Residual stress generation and evaluation in milling: A review. Int. J. Adv. Manuf. Technol. 2023, 126, 3783-3812. DOI: 10.1007/s00170-023-11394-1

[155] Rossini N, Dassisti M, Benyounis K, Olabi A. Methods of measuring residual stresses in components. Mater. Des. 2012, 35, 572-588. DOI: 10.1016/j.matdes.2011.08.022

[156] Seers B, Tomlinson R, Fairclough P. Residual stress in fiber reinforced thermosetting composites: A review of measurement techniques. Polym. Compos. 2021, 42, 1631-1647. DOI: 10.1002/pc.25934

[157] Schmeiser F, Krohmer E, Schell N, Uhlmann E, Reimers W. Experimental observation of stress formation during selective laser melting using in situX-ray diffraction. Addit. Manuf. 2020, 32, 101028. DOI: 10.1016/j.addma.2019.101028

[158] Goel S, Neikter M, Capek J, Polatidis E, Colliander M, Joshi S, et al. Residual stress determination by neutron diffraction in powder bed fusion-built Alloy 718: Influence of process parameters and post-treatment. Mater. Des. 2020, 195, 109045. DOI: 10.1016/j.matdes.2020.109045

[159] Maurya P, Kota N, Gibmeier J, Wanner A, Roy S. Review on study of internal load transfer in metal matrix composites using diffraction techniques. Mater. Sci. Eng. A 2022, 840, 142973. DOI: 10.1016/j.msea.2022.142973

[160] Lee Y, Feldhausen T, Fancher C, Nandwana P, Babu S, Simunovic S, et al. Prediction of residual strain/stress validated with neutron diffraction method for wire-feed hybrid additive/subtractive manufacturing. Addit. Manuf. 2024, 79, 103920. DOI: 10.1016/j.addma.2023.103920

[161] Gurmesa F, Lemu H, Adugna Y, Harsibo M. Residual Stresses in Wire Arc Additive Manufacturing Products and Their Measurement Techniques: A Systematic Review. Appl. Mech. 2024, 5, 420-449. DOI: 10.3390/applmech5030025

[162] Zhang Y, Yu W, Zheng Z, Lai Y. A comprehensive review of residual stress in metal additive manufacturing: Detection techniques, numerical simulation, and mitigation strategies. J. Braz. Soc. Mech. Sci. Eng. 2025, 47, 17. DOI: 10.1007/s40430-024-05319-6

[163] Li R, Xiong J, Lei Y. Investigation on thermal stress evolution induced by wire and arc additive manufacturing for circular thin-walled parts. J. Manuf. Process. 2019, 40, 59-67. DOI: 10.1016/j.jmapro.2019.03.006

[164] Ahmad B, van der Veen S, Fitzpatrick M, Guo H. Residual stress evaluation in selective-laser-melting additively manufactured titanium (Ti-6Al-4V) and inconel 718 using the contour method and numerical simulation. Addit. Manuf. 2018, 22, 571-582. DOI: 10.1016/j.addma.2018.06.002

[165] Hong Y, Wang C, Wang L, She S, Lei J, Ji V. Characterization of microscopic residual stresses: A review. Eng. Fract. Mech. 2024, 310, 110441. DOI: 10.1016/j.engfracmech.2024.110441

[166] Kim I, Park S, Kim Y, Kim D, Lee K, Oh S, et al. Surface residual stress analysis of additive manufactured AlSi10Mg alloys. J. Alloys Compd. 2023, 945, 169315. DOI: 10.1016/j.jallcom.2023.169315

[167] Long X, Dong R, Su Y, Chang C. Critical Review of Nanoindentation-Based Numerical Methods for Evaluating Elastoplastic Material Properties. Coatings 2023, 13, 1334. DOI: 10.3390/coatings13081334

[168] Peng W, Jiang W, Yang B, Sun G, Shao X. An indentation method for measuring welding residual stress: Estimation of stress-free indentation curve using BP neural network prediction model. Int. J. Press. Vessel. Pip. 2023, 206, 105070. DOI: 10.1016/j.ijpvp.2023.105070

[169] Roskosz M, Bieniek M. Evaluation of residual stress in ferromagnetic steels based on residual magnetic field measurements. NDT E Int. 2012, 45, 55-62. DOI: 10.1016/j.ndteint.2011.09.007

[170] Dubov A, Kolokolnikov S. The metal magnetic memory method application for online monitoring of damage development in steel pipes and welded joints specimens. Weld. World 2013, 57, 123-136. DOI: 10.1007/s40194-012-0011-5

[171] Lu Y, Sun G, Xiao X, Mazumder J. Online Stress Measurement During Laser-aided Metallic Additive Manufacturing. Sci. Rep. 2019, 9, 7630. DOI: 10.1038/s41598-019-39849-0

[172] Shi X, Xiu S, Su H. Residual stress model of pre-stressed dry grinding considering coupling of thermal, stress, and phase transformation. Adv. Manuf. 2019, 7, 401-410. DOI: 10.1007/s40436-019-00280-3

[173] Zeng G, Zu R, Wu D, Shi W, Zhou J, Zhao J, et al. A Hybrid Method for the Online Evaluation of Stress Fields in Metal Additive Manufacturing. Exp. Mech. 2021, 61, 1261-1270. DOI: 10.1007/s11340-021-00735-4

[174] Bartlett J, Croom B, Burdick J, Henkel D, Li X. Revealing mechanisms of residual stress development in additive manufacturing via digital image correlation. Addit. Manuf. 2018, 22, 1-12. DOI: 10.1016/j.addma.2018.04.025

[175] Heigel J, Phan T, Fox J, Gnaupel-Herold T. Experimental Investigation of Residual Stress and its Impact on Machining in Hybrid Additive/Subtractive Manufacturing. Procedia Manuf. 2018, 26, 929-940. DOI: 10.1016/j.promfg.2018.07.120

[176] Zhang Z, Qin R, Li G, Du Z, Li Z, Lin Y, et al. Deep learning-based monitoring of surface residual stress and efficient sensing of AE for laser shock peening. J. Mater. Process. Technol. 2022, 303, 117515. DOI: 10.1016/j.jmatprotec.2022.117515

[177] Xia C, Julien S, Duran S, Chang-Davidson E, Paul S, Müftü S. Surrogate modelling of thermal and residual stress fields in cold-spray additive manufacturing using machine learning. Virtual Phys. Prototyp. 2025, 20, e2559996. DOI: 10.1080/17452759.2025.2559996

[178] Huang W, Wang Q, Ma N, Kitano H. Distribution characteristics of residual stresses in typical wall and pipe components built by wire arc additive manufacturing. J. Manuf. Process. 2022, 82, 434-447. DOI: 10.1016/j.jmapro.2022.08.010

[179] Guerain M, Duriez C, Grosseau-Poussard JL, Mermoux M. Review of stress fields in Zirconium alloys corrosion scales. Corros. Sci. 2015, 95, 11-21. DOI: 10.1016/j.corsci.2015.03.004

[180] Tu S, Ren X, He J, Zhang Z. Stress-strain curves of metallic materials and post‐necking strain hardening characterization: A review. Fatigue Fract. Eng. Mat. Struct. 2020, 43, 3-19. DOI: 10.1111/ffe.13134

[181] Yang Y, Xia L, Zhao G, Meng L, He N. Investigation of the coupled distribution of initial and machining-induced residual stress on the surface of thin-walled parts. Int. J. Adv. Manuf. Technol. 2018, 98, 213-222. DOI: 10.1007/s00170-017-1567-4

[182] Liu C, Zhang Y, Zhu L, Li Q, Shu X, Qin S, et al. A Review of Ultrasonic Vibration-Assisted Grinding for Advanced Materials. Intell. Sustain. Manuf. 2025, 2, 10001. DOI: 10.70322/ism.2025.10001

[183] Pardini C, Anselmo L. Monitoring the orbital decay of the Chinese space station Tiangong-1 from the loss of control until the re-entry into the Earth’s atmosphere. J. Space Saf. Eng. 2019, 6, 265-275. DOI: 10.1016/j.jsse.2019.10.004

[184] Huang Y, Wu Y, Xiao G, Zhang Y, Wang W. Analysis of abrasive belt wear effect on residual stress distribution on a grinding surface. Wear 2021, 486-487, 204113. DOI: 10.1016/j.wear.2021.204113

[185] Hou Y, Zuo D, Sun Y, Wang L, Li L. Distributional analysis of residual stresses with the Ti-6Al-4V internal trapezoidal thread torsional vibration extrusion. Int. J. Adv. Manuf. Technol. 2019, 105, 4289-4307. DOI: 10.1007/s00170-019-04472-w

[186] Song H, Gao H, Wu Q, Zhang Y. Residual stress relief mechanisms of 2219 Al-Cu alloy by thermal stress relief method. Rev. Adv. Mater. Sci. 2022, 61, 102-116. DOI: 10.1515/rams-2022-0019

[187] Idarraga I, Mermoux M, Duriez C, Crisci A, Mardon J. Potentialities of Raman Imaging for the Analysis of Oxide Scales Formed on Zircaloy-4 and M5® in Air at High Temperature. Oxid. Met. 2013, 79, 289-302. DOI: 10.1007/s11085-012-9331-5

[188] Sun B, Zhao J, Qiao H, Lu Y. Residual Stress Distribution and Dynamic Stress Variation in Aluminum Alloy Round Rods after Laser Shock Peening. J. Mater. Eng. Perform. 2022, 31, 9073-9082. DOI: 10.1007/s11665-022-06885-3

[189] Xu Q, Liu Z, Yang X, Zhang C, Liu J, Li G. Evolutions of porosity, microstructure, microhardness, and residual stress in 316L stainless steel subjected to interlayer hybrid laser additive, milling subtractive, and ultrasonic rolling equivalent manufacturing process. Mater. Today Commun. 2025, 46, 112565. DOI: 10.1016/j.mtcomm.2025.112565

[190] Karunakaran R, Sotelo L, Maharaja H, Nez C, Ramoni M, Halliday S, et al. Increased ductility of Ti-6Al-4V by interlayer milling during directed energy deposition. Addit. Manuf. 2023, 78, 103818. DOI: 10.1016/j.addma.2023.103818

[191] Uçak N, Outeiro J, Çiçek A, Aslantas K. Numerical analysis of the influence of sequential cuts during micro-milling of wrought and LPBF Ti6Al4V alloys. Manuf. Lett. 2025, 44, 622-630. DOI: 10.1016/j.mfglet.2025.06.073

[192] Liu C, Zhao W, Gao X, Wang N, Lv Y, Ning Z, et al. LDED-based additive-subtractive hybrid manufacturing of Inconel 718 superalloy: Evolution of microstructure and residual stress. Virtual Phys. Prototyp. 2024, 19, e2400329. DOI: 10.1080/17452759.2024.2400329

[193] Yan Z, Guo J, Zou X, Wang S. Integrated Control of Thermal Residual Stress and Mechanical Properties by Adjusting Pulse-Wave Direct Energy Deposition. Materials 2024, 17, 5231. DOI: 10.3390/ma17215231

[194] Lisiecki A, Ślizak D. Hybrid Laser Deposition of Composite WC-Ni Layers with Forced Local Cryogenic Cooling. Materials 2021, 14, 4312. DOI: 10.3390/ma14154312

[195] Ma L, Qiu W, Fan X. Stress/strain characterization in electronic packaging by micro-Raman spectroscopy: A review. Microelectron. Reliab. 2021, 118, 114045. DOI: 10.1016/j.microrel.2021.114045

[196] Yi G, Liang Y, Wang C, Xu J. Evolution of Residual Stress Based on Curvature Coupling in Multi-Roll Levelling. Appl. Sci. 2019, 9, 4975. DOI: 10.3390/app9224975

[197] Yuan Z, Wang Y, Yang G, Tang A, Yang Z, Li S, et al. Evolution of curing residual stresses in composite using multi-scale method. Compos. Part B Eng. 2018, 155, 49-61. DOI: 10.1016/j.compositesb.2018.08.012

[198] Koo S, Hoshikawa Y, Kawagoe Y, Ryuzono K, Okabe T. Process-induced residual stress in non-crimp fabric composites: Experimental and numerical evaluation considering viscoelasticity. Mech. Mater. 2025, 209, 105423. DOI: 10.1016/j.mechmat.2025.105423

[199] Li C, Ji B, Yao Y. Stress biaxiality-based residual stress assessment in welded T-joints using the blind-hole method. J. Constr. Steel Res. 2024, 216, 108610. DOI: 10.1016/j.jcsr.2024.108610

[200] Shipley H, McDonnell D, Culleton M, Coull R, Lupoi R, O’Donnell G, et al. Optimisation of process parameters to address fundamental challenges during selective laser melting of Ti-6Al-4V: A review. Int. J. Mach. Tools Manuf. 2018, 128, 1-20. DOI: 10.1016/j.ijmachtools.2018.01.003

[201] Liu D, Lee B, Babkin A, Chang Y. Research Progress of Arc Additive Manufacture Technology. Materials 2021, 14, 1415. DOI: 10.3390/ma14061415

[202] Zhang Y, Wang C, Xu W, Zhang X, Ren K, Wang S, et al. Laser Cutting of Titanium Alloy Plates: A Review of Processing, Microstructure, and Mechanical Properties. Metals 2024, 14, 1152. DOI: 10.3390/met14101152

[203] Ding D, Pan Z, Cuiuri D, Li H. Wire-feed additive manufacturing of metal components: Technologies, developments and future interests. Int. J. Adv. Manuf. Technol. 2015, 81, 465-481. DOI: 10.1007/s00170-015-7077-3

[204] Yang Y, Yan S, Qu S, Yi M, Chen Z, Zhou T, et al. Microstructure of titanium alloy in additive/subtractive hybrid manufacturing: A review. J. Alloys Compd. 2025, 1014, 178769. DOI: 10.1016/j.jallcom.2025.178769

[205] Cheng M, Zou X, Pan Y, Zhou Y, Liu W, Song L. Residual Stress Control Using Process Optimization in Directed Energy Deposition. Materials 2023, 16, 6610. DOI: 10.3390/ma16196610

[206] Chen Q, Liang X, Hayduke D, Liu J, Cheng L, Oskin J, et al. An inherent strain based multiscale modeling framework for simulating part-scale residual deformation for direct metal laser sintering. Addit. Manuf. 2019, 28, 406-418. DOI: 10.1016/j.addma.2019.05.021

[207] Zhao H, Liu Z, Yu C, Liu C, Zhan Y. Finite element analysis for residual stress of TC4/Inconel718 functionally gradient materials produced by laser additive manufacturing. Opt. Laser Technol. 2022, 152, 108146. DOI: 10.1016/j.optlastec.2022.108146

[208] Bian P, Shi J, Liu Y, Xie Y. Influence of laser power and scanning strategy on residual stress distribution in additively manufactured 316L steel. Opt. Laser Technol. 2020, 132, 106477. DOI: 10.1016/j.optlastec.2020.106477

[209] McCann R, Obeidi M, Hughes C, McCarthy É, Egan D, Vijayaraghavan R, et al. In-situ sensing, process monitoring and machine control in Laser Powder Bed Fusion: A review. Addit. Manuf. 2021, 45, 102058. DOI: 10.1016/j.addma.2021.102058

[210] Dar J, Ponsot A, Jolma C, Lin D. A review on scan strategies in laser-based metal additive manufacturing. J. Mater. Res. Technol. 2025, 36, 5425-5467. DOI: 10.1016/j.jmrt.2025.04.068

[211] Yeung H, Lane B. A residual heat compensation based scan strategy for powder bed fusion additive manufacturing. Manuf. Lett. 2020, 25, 56-59. DOI: 10.1016/j.mfglet.2020.07.005

[212] Oliveira J, LaLonde A, Ma J. Processing parameters in laser powder bed fusion metal additive manufacturing. Mater. Des. 2020, 193, 108762. DOI: 10.1016/j.matdes.2020.108762

[213] Nandhakumar R, Venkatesan K. A process parameters review on selective laser melting-based additive manufacturing of single and multi-material: Microstructure, physical properties, tribological, and surface roughness. Mater. Today Commun. 2023, 35, 105538. DOI: 10.1016/j.mtcomm.2023.105538

[214] Chenglin Z, Yan W, Haiyi L, Mengcan Y, Xiaohui J. Effect of process parameters on residual stresses in SLM-formed bionic porous titanium alloy structures. Mater. Today Commun. 2024, 39, 108539. DOI: 10.1016/j.mtcomm.2024.108539

[215] Chen C, Yin J, Zhu H, Zeng X, Wang G, Ke L, et al. The effect of process parameters on the residual stress of selective laser melted Inconel 718 thin-walled part. Rapid Prototyp. J. 2019, 25, 1359-1369. DOI: 10.1108/RPJ-09-2018-0249

[216] Xu S, Liu J, Li X, Ma Y. Concurrent Island scanning pattern and large-scale topology optimization method for laser powder bed fusion processed parts. Finite Elem. Anal. Des. 2023, 225, 104018. DOI: 10.1016/j.finel.2023.104018

[217] Chen Q, Liu J, Liang X, To A. A level-set based continuous scanning path optimization method for reducing residual stress and deformation in metal additive manufacturing. Comput. Methods Appl. Mech. Eng. 2020, 360, 112719. DOI: 10.1016/j.cma.2019.112719

[218] Shamsaei N, Yadollahi A, Bian L, Thompson S. An overview of Direct Laser Deposition for additive manufacturing; Part II: Mechanical behavior, process parameter optimization and control. Addit. Manuf. 2015, 8, 12-35. DOI: 10.1016/j.addma.2015.07.002

[219] Chen C, Chang S, Zhu J, Xiao Z, Zhu H, Zeng X. Residual stress of typical parts in laser powder bed fusion. J. Manuf. Process. 2020, 59, 621-628. DOI: 10.1016/j.jmapro.2020.10.009

[220] Yan Z, Guo J, Song L. Improved molten-pool boundary stability and residual stress for microstructure control using additive manufacturing utilizing quasi-continuous-wave laser. Opt. Laser Technol. 2025, 192, 113561. DOI: 10.1016/j.optlastec.2025.113561

[221] Kazemi Movahed A, Ghanavati R, Saboori A, Iuliano L. A Review of Strategies for In Situ Mitigating of Residual Stress in Laser-Based Metal Additive Manufacturing: Insights, Innovations, and Challenges. Acta Metall. Sin. 2025, 38, 1657-1698. DOI: 10.1007/s40195-025-01902-5

[222] Teixeira Ó, Silva FJG, Ferreira LP, Atzeni E. A Review of Heat Treatments on Improving the Quality and Residual Stresses of the Ti-6Al-4V Parts Produced by Additive Manufacturing. Metals 2020, 10, 1006. DOI: 10.3390/met10081006

[223] Motallebi R, Savaedi Z, Mirzadeh H. Post-processing heat treatment of lightweight magnesium alloys fabricated by additive manufacturing: A review. J. Mater. Res. Technol. 2022, 20, 1873-1892. DOI: 10.1016/j.jmrt.2022.07.154

[224] Sanusi K, Malatji N, Jeje S, Kanyane R, Shongwe M. A review on heat treatment of laser additive manufactured medium entropy alloys. Int. J. Adv. Manuf. Technol. 2025, 137, 5405-5429. DOI: 10.1007/s00170-025-15479-x

[225] Barros R, Silva F, Gouveia R, Saboori A, Marchese G, Biamino S, et al. Laser Powder Bed Fusion of Inconel 718: Residual Stress Analysis Before and After Heat Treatment. Metals 2019, 9, 1290. DOI: 10.3390/met9121290

[226] Wang X, Chou K. The effects of stress relieving heat treatment on the microstructure and residual stress of Inconel 718 fabricated by laser metal powder bed fusion additive manufacturing process. J. Manuf. Process. 2019, 48, 154-163. DOI: 10.1016/j.jmapro.2019.10.027

[227] Marchese G, Piscopo G, Lerda S, Salmi A, Atzeni E, Biamino S. Heat-Treated Inconel 625 by Laser Powder Bed Fusion: Microstructure, Tensile Properties, and Residual Stress Evolution. J. Mater. Eng. Perform. 2024, 33, 6825-6834. DOI: 10.1007/s11665-024-09235-7

[228] Gu L, Zhang J, Liu Y, Liu Z, Wang Q, He L, et al. Macroscopic and microscopic residual stress relief in SiC/Al composites: Effects of annealing and cryogenic treatment. J. Mater. Sci. Technol. 2026, 254, 106-116. DOI: 10.1016/j.jmst.2025.08.013

[229] Zhou F, Hu X, Zhou Y, Xu Z, Guo C, Li G, et al. Effects of post-heat treatment on anisotropic mechanical properties of laser additively manufactured IN718. Mater. Sci. Eng. A 2023, 877, 145144. DOI: 10.1016/j.msea.2023.145144

[230] Tan C, Li R, Su J, Du D, Du Y, Attard B, et al. Review on field assisted metal additive manufacturing. Int. J. Mach. Tools Manuf. 2023, 189, 104032. DOI: 10.1016/j.ijmachtools.2023.104032

[231] Nguyen H, Pramanik A, Basak A, Dong Y, Prakash C, Debnath S, et al. A critical review on additive manufacturing of Ti-6Al-4V alloy: Microstructure and mechanical properties. J. Mater. Res. Technol. 2022, 18, 4641-4661. DOI: 10.1016/j.jmrt.2022.04.055

[232] Aziz U, McAfee M, Manolakis I, Timmons N, Tormey D. A Review of Optimization of Additively Manufactured 316/316L Stainless Steel Process Parameters, Post-Processing Strategies, and Defect Mitigation. Materials 2025, 18, 2870. DOI: 10.3390/ma18122870

[233] Mokhtari Homami R, Wanjara P, Gholipour J, Asala G, Akinrinlola B, Ojo O. Numerical analysis of residual stress in a material produced by additive manufacturing and hot isostatic pressing. J. Manuf. Process. 2025, 150, 1018-1039. DOI: 10.1016/j.jmapro.2025.06.108

[234] Niu H, Liu Z, Wang H, Wu H, Liu Q, Fan G. Effects of hot isostatic pressing on the micron-scale residual stress of nickel-based single-crystal superalloys. J. Mater. Sci. Technol. 2025, 221, 102-116. DOI: 10.1016/j.jmst.2024.09.036

[235] Zhou C, Sun Q, Qian D, Liu J, Sun J, Sun Z. Effect of deep cryogenic treatment on mechanical properties and residual stress of AlSi10Mg alloy fabricated by laser powder bed fusion. J. Mater. Process. Technol. 2022, 303, 117543. DOI: 10.1016/j.jmatprotec.2022.117543

[236] Ding C, Cui X, Jiao J, Zhu P. Effects of Substrate Preheating Temperatures on the Microstructure, Properties, and Residual Stress of 12CrNi2 Prepared by Laser Cladding Deposition Technique. Materials 2018, 11, 2401. DOI: 10.3390/ma11122401

[237] Bai X, Zhang H, Wang G. Modeling of the moving induction heating used as secondary heat source in weld-based additive manufacturing. Int. J. Adv. Manuf. Technol. 2015, 77, 717-727. DOI: 10.1007/s00170-014-6475-2

[238] Martina F, Roy M, Szost B, Terzi S, Colegrove P, Williams S, et al. Residual stress of as-deposited and rolled wire+arc additive manufacturing Ti-6Al-4V components. Mater. Sci. Technol. 2016, 32, 1439-1448. DOI: 10.1080/02670836.2016.1142704

[239] Zhao X, Wang Y, Wang G, Li R, Zhang H. Effect of process parameters on stress and strain of hybrid deposition and micro-rolling. Rapid Prototyp. J. 2022, 28, 490-504. DOI: 10.1108/RPJ-01-2021-0012

[240] Shen H, Lin J, Zhou Z, Liu B. Effect of induction heat treatment on residual stress distribution of components fabricated by wire arc additive manufacturing. J. Manuf. Process. 2022, 75, 331-345. DOI: 10.1016/j.jmapro.2022.01.018

[241] Yadav S, Liu S, Singh R, Sharma A, Rawat P. A state-of-art review on functionally graded materials (FGMs) manufactured by 3D printing techniques: Advantages, existing challenges, and future scope. J. Manuf. Process. 2024, 131, 2051-2072. DOI: 10.1016/j.jmapro.2024.10.026

[242] Wang X, Zhai W, Li H, Wang J, Wei B. Ultrasounds induced eutectic structure transition and associated mechanical property enhancement of FeCoCrNi_2.1Al high entropy alloy . Acta Mater. 2023, 252, 118900. DOI: 10.1016/j.actamat.2023.118900

[243] Yan P, Chang J, Wang W, Zhu X, Lin M, Wei B. Metastable phase separation and crystalline orientation feature of electromagnetic levitation processed CoCrCuFeNi high entropy alloy. Acta Mater. 2024, 269, 119778. DOI: 10.1016/j.actamat.2024.119778

[244] Arif Z, Khalid M, ur Rehman E, Ullah S, Atif M, Tariq A. A review on laser cladding of high-entropy alloys, their recent trends and potential applications. J. Manuf. Process. 2021, 68, 225-273. DOI: 10.1016/j.jmapro.2021.06.041

[245] Zhang W, Chabok A, Kooi B, Pei Y. Additive manufactured high entropy alloys: A review of the microstructure and properties. Mater. Des. 2022, 220, 110875. DOI: 10.1016/j.matdes.2022.110875

[246] Yan P, Chang J, Wang W, Zhu X, Lin M, Wei B. Eutectic growth kinetics and microscopic mechanical properties of rapidly solidified CoCrFeNiMo_0.8 high entropy alloy . Acta Mater. 2022, 237, 118149. DOI: 10.1016/j.actamat.2022.118149

[247] Bui T, Fang T, Lee C. Deformation and machining mechanism of nanocrystalline NiCoCrFe high entropy alloys. J. Alloys Compd. 2022, 924, 166525. DOI: 10.1016/j.jallcom.2022.166525

[248] Lin D, Hu J, Song X, Tang Z, Wang Y, Hu S, et al. Vacuum brazing SiC to Mo using Nb_0.74CoCrFeNi₂ eutectic high-entropy alloy filler. Mater. Charact. 2023, 204, 113199. DOI: 10.1016/j.matchar.2023.113199

[249] Li H, Lee T, Zheng W, Lu Y, Yin H, Yang J, et al. Characterization of residual stress in laser melting deposited CoCrFeMnNi high entropy alloy by neutron diffraction. Mater. Lett. 2020, 263, 127247. DOI: 10.1016/j.matlet.2019.127247

[250] Sun Z, Tan X, Wang C, Descoins M, Mangelinck D, Tor S, et al. Reducing hot tearing by grain boundary segregation engineering in additive manufacturing: Example of an AlxCoCrFeNi high-entropy alloy. Acta Mater. 2021, 204, 116505. DOI: 10.1016/j.actamat.2020.116505

[251] Li H, Wang X, Wang J, Zhai W, Wei B. Strengthening Cu-containing high entropy alloys through ultrasonic solidification constructed heterostructures. Mater. Sci. Eng. A 2024, 916, 147336. DOI: 10.1016/j.msea.2024.147336

[252] Manimaran G, Anwar S, Rahman M, Erdi Korkmaz M, Gupta M, Alfaify A, et al. Investigation of surface modification and tool wear on milling Nimonic 80A under hybrid lubrication. Tribol. Int. 2021, 155, 106762. DOI: 10.1016/j.triboint.2020.106762

[253] Chen Y, Yue C, Zhang W, Peng Y, Liu X, Gao Y, et al. Construction of strong coupling interface between Diamond@WC/Co and CuSn matrix for interfacial stress modulation. Diam. Relat. Mater. 2025, 153, 112054. DOI: 10.1016/j.diamond.2025.112054

[254] Wang X, Li J, Zhang Y, Wang Y. Improvement of interfacial bonding and mechanical properties of Cu-Al₂O₃ composite by Cr-nanoparticle-induced interfacial modification . J. Alloys Compd. 2017, 695, 2124-2130. DOI: 10.1016/j.jallcom.2016.11.055

[255] Riggins A, Dadmun M. Controlling residual stress in material extrusion 3D printing through material formulation. Addit. Manuf. 2023, 73, 103678. DOI: 10.1016/j.addma.2023.103678

[256] Kattoura M, Telang A, Mannava S, Qian D, Vasudevan V. Effect of Ultrasonic Nanocrystal Surface Modification on residual stress, microstructure and fatigue behavior of ATI 718Plus alloy. Mater. Sci. Eng. A 2018, 711, 364-377. DOI: 10.1016/j.msea.2017.11.043

[257] Gill A, Telang A, Mannava S, Qian D, Pyoun Y, Soyama H, et al. Comparison of mechanisms of advanced mechanical surface treatments in nickel-based superalloy. Mater. Sci. Eng. A 2013, 576, 346-355. DOI: 10.1016/j.msea.2013.04.021

[258] Gisario A, Kazarian M, Martina F, Mehrpouya M. Metal additive manufacturing in the commercial aviation industry: A review. J. Manuf. Syst. 2019, 53, 124-149. DOI: 10.1016/j.jmsy.2019.08.005

[259] Wan N, Zhao B, Ding W, He Q. Research status and tendency on cold expansion anti-fatigue manufacturing technology for aircraft structural fastening holes. J. Manuf. Process. 2025, 141, 319-335. DOI: 10.1016/j.jmapro.2025.02.068

[260] Wu K, van Keulen F, Wu J. Residual stress-constrained space-time topology optimization for multi-axis additive manufacturing. Comput. Methods Appl. Mech. Eng. 2025, 440, 117913. DOI: 10.1016/j.cma.2025.117913

[261] Wu C, Wang C, Kim J. Welding sequence optimization to reduce welding distortion based on coupled artificial neural network and swarm intelligence algorithm. Eng. Appl. Artif. Intell. 2022, 114, 105142. DOI: 10.1016/j.engappai.2022.105142

[262] Shao Z, Zhang C, Li Y, Shen H, Zhang D, Yu X, et al. A Review of Non-Destructive Evaluation (NDE) Techniques for Residual Stress Profiling of Metallic Components in Aircraft Engines. Aerospace 2022, 9, 534. DOI: 10.3390/aerospace9100534

[263] Fan J, Wang Z, Liu C, Shi D, Yang X. A tensile properties-related fatigue strength predicted machine learning framework for alloys used in aerospace. Eng. Fract. Mech. 2024, 301, 110057. DOI: 10.1016/j.engfracmech.2024.110057

[264] Zhang Z, Luo M, Tang K, Zhang D. A new in-processes active control method for reducing the residual stresses induced deformation of thin-walled parts. J. Manuf. Process. 2020, 59, 316-325. DOI: 10.1016/j.jmapro.2020.09.079

[265] Ji S, Yang Z, Wen Q, Yue Y, Zhang L. Effect of Trailing Intensive Cooling on Residual Stress and Welding Distortion of Friction Stir Welded 2060 Al-Li Alloy. High Temp. Mater. Process. 2018, 37, 397-403. DOI: 10.1515/htmp-2016-0217

[266] Satya Hanush S, Manjaiah M. Topology optimization of aerospace part to enhance the performance by additive manufacturing process. Mater. Today Proc. 2022, 62, 7373-7378. DOI: 10.1016/j.matpr.2022.02.074

[267] Careri F, Khan R, Todd C, Attallah M. Additive manufacturing of heat exchangers in aerospace applications: A review. Appl. Therm. Eng. 2023, 235, 121387. DOI: 10.1016/j.applthermaleng.2023.121387

[268] Abd El-Aty A, Xu Y, Guo X, Zhang S, Ma Y, Chen D. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: A review. J. Adv. Res. 2018, 10, 49-67. DOI: 10.1016/j.jare.2017.12.004

[269] Li S, Yue X, Li Q, Peng H, Dong B, Liu T, et al. Development and applications of aluminum alloys for aerospace industry. J. Mater. Res. Technol. 2023, 27, 944-983. DOI: 10.1016/j.jmrt.2023.09.274

[270] Li H, Wang M, Lou D, Xia W, Fang X. Microstructural features of biomedical cobalt-chromium-molybdenum (CoCrMo) alloy from powder bed fusion to aging heat treatment. J. Mater. Sci. Technol. 2020, 45, 146-156. DOI: 10.1016/j.jmst.2019.11.031

[271] Lowther M, Louth S, Davey A, Hussain A, Ginestra P, Carter L, et al. Clinical, industrial, and research perspectives on powder bed fusion additively manufactured metal implants. Addit. Manuf. 2019, 28, 565-584. DOI: 10.1016/j.addma.2019.05.033

[272] Vijayan V, Panneerselvam K, Sathiya P. Advancements in biocompatibility and mechanical behaviour of wire arc additive manufacturing for biomedical applications. Multiscale Multidiscip. Model. Exp. Des. 2025, 8, 190. DOI: 10.1007/s41939-025-00791-6

[273] Ginestra P, Ferraro R, Zohar-Hauber K, Abeni A, Giliani S, Ceretti E. Selective Laser Melting and Electron Beam Melting of Ti6Al4V for Orthopedic Applications: A Comparative Study on the Applied Building Direction. Materials 2020, 13, 5584. DOI: 10.3390/ma13235584

[274] Ninpetch P, Kowitwarangkul P, Chalermkarnnon P, Promoppatum P, Chuchuay P, Rattanadecho P. Numerical Modeling of Distortion of Ti-6Al-4V Components Manufactured Using Laser Powder Bed Fusion. Metals 2022, 12, 1484. DOI: 10.3390/met12091484

[275] Chowdhury S, Arunachalam N. Surface functionalization of additively manufactured titanium alloy for orthopaedic implant applications. J. Manuf. Process. 2023, 102, 387-405. DOI: 10.1016/j.jmapro.2023.07.015

[276] Kannan S, Srinivasan S. Influence of manufacturing processes and their sequence of execution on fatigue life of axle house tubes in automobiles. Eng. Fail. Anal. 2013, 34, 79-92. DOI: 10.1016/j.engfailanal.2013.07.013

[277] Nugroho W, Dong Y, Pramanik A, Chithirai Pon Selvan M, Zhang Z, Ramakrishna S. Additive manufacturing of re-entrant structures: Well-tailored structures, unique properties, modelling approaches and real applications. Addit. Manuf. 2023, 78, 103829. DOI: 10.1016/j.addma.2023.103829

[278] Wang H, Xie H, Cheng W, Liu Q, Shen Y. Multi-objective optimisation on crashworthiness of front longitudinal beam (FLB) coupled with sheet metal stamping process. Thin-Walled Struct. 2018, 132, 36-47. DOI: 10.1016/j.tws.2018.07.050

[279] Park S, Kim T, Kim K, Seo J, Chung J, Choi J, et al. Quick dimensional inspection for continuous welding and assembly using machine learning-powered smart jig. J. Manuf. Syst. 2025, 82, 478-496. DOI: 10.1016/j.jmsy.2025.07.001

[280] Kudrna L, Fojtík F, Kozák J, Váňová P, Ma Q, Hajnyš J, et al. Comparative analysis of residual stress distributions in a braking pedal from a historical motorbike manufactured via selective laser melting and wire arc additive manufacturing. Int. J. Adv. Manuf. Technol. 2025, 138, 1113-1127. DOI: 10.1007/s00170-025-15593-w

[281] Kumar L, Goyal A, Pathak VK, Bhowmik A. A state-of-the-art review of soft computing-based monitoring and control in the machining of hard alloys. Discov. Appl. Sci. 2025, 7, 681. DOI: 10.1007/s42452-025-07385-4