Transition metal carbide-engineered active layers for high-efficiency and stable perovskite solar cell

Abstract

We introduce an innovative perovskite solar cell (PSC) architecture featuring a multifunctional active layer (AL) of FA_0.85MA_0.15PbI₃ (FA: formamidine, MA: methylamine) integrated with two dimensional (2D) transition metal carbides (TiC/WC). The properties of the chemically reduced WC and TiC were thoroughly validated through structural and morphological analyses. This design significantly enhances the conventional charge-transporting properties of the AL by utilizing conductive carbide networks (conductivity (σ) > 1200 S/cm) and achieving defect passivation at grain boundaries (reducing trap density from 10¹⁶ to 10¹⁴ cm⁻³), along with providing intrinsic stability against environmental stressors. Devices constructed with the AL@WC configuration achieved a remarkable power conversion efficiency (PCE) of 24.25%, surpassing both the TiC-incorporated devices (23.74%) and the pristine AL devices (22.56%). Significantly, after 800 h in ambient air conditions (40% relative humidity), the AL@WC device retained 86% of its initial PCE under dark conditions and 81% under continuous illumination. In a nitrogen environment, dark stability measurements indicated a retention rate of 89%, while illumination stability exhibited an 83% retention for the AL@WC, affirming the enhanced protective capabilities and stability provided by the WC-integrated FA_0.85MA_0.15PbI₃ AL configuration. This work establishes a simplified and high-performance PSC paradigm by effectively uniting charge extraction and stabilization within the AL, paving the way for scalable photovoltaics exceeding 24% efficiency and operational stability.

Keywords

solar cells / perovskites / titanium carbide / tungsten carbide

References

[1] M. Cinquino, A. Fieramosca, R. Mastria, et al., Managing growth and dimensionality of quasi 2D perovskite single-crystalline flakes for tunable excitons orientation, Adv. Mater., 33(2021), No. 48, art. No. 2102326.

[2] Giacomo FD, Fakharuddin A, Jose R, Brown TM. Progress, challenges and perspectives in flexible perovskite solar cells. Energy Environ. Sci., 2016, 9(10): 3007

[3] T.M. Brenner, D.A. Egger, L. Kronik, G. Hodes, and D. Cahen, Hybrid organic–inorganic perovskites: Low-cost semiconductors with intriguing charge-transport properties, Nat. Rev. Mater., 1(2016), art. No. 15007.

[4] Baena JPC, Saliba M, Buonassisi T, et al. . Promises and challenges of perovskite solar cells. Science, 2017, 358(6364): 739

[5] Herz LM. Charge-carrier mobilities in metal halide perovskites: Fundamental mechanisms and limits. ACS Energy Lett., 2017, 2(7): 1539

[6] Zhao X, Gao NT, Wu SC, Li SZ, Wu SJ. Enhancing performance of low-temperature processed CsPbI₂Br all-inorganic perovskite solar cells using polyethylene oxide-modified TiO₂. Int. J. Miner. Metall. Mater., 2024, 31(4): 786

[7] Goetz KP, Taylor AD, Hofstetter YJ, Vaynzof Y. Sustainability in perovskite solar cells. ACS Appl. Mater. Interfaces, 2021, 13(1): 1

[8] Hussain S, Liu HL, Hussain M, et al. . Development of MXene/WO₃ embedded PEDOT:PSS hole transport layers for highly efficient perovskite solar cells and X-ray detectors. Int. J. Energy Res., 2022, 46(9): 12485

[9] Zhao X, Zhong SD, Wang SQ, Li SZ, Wu SJ. Potassium thiocyanate additive for PEDOT:PSS layer to fabricate efficient tin-based perovskite solar cells. Int. J. Miner. Metall. Mater., 2023, 30(12): 2451

[10] H.S. Li, R. Zhang, Y.S. Li, et al., Graphdiyne-based bulk heterojunction for efficient and moisture-stable planar perovskite solar cells, Adv. Energy Mater., 8(2018), No. 30, art. No. 1802012.

[11] J.V. Mili, N. Arora, M.I. Dar, S.M. Zakeeruddin, and M. Grätzel, Reduced graphene oxide as a stabilizing agent in perovskite solar cells, Adv. Mater. Interfaces, 5(2018), No. 22, art. No. 1800416.

[12] Q. Luo, R.G. Wu, L.T. Ma, et al., Recent advances in carbon nanotube utilizations in perovskite solar cells, Adv. Funct. Mater., 31(2021), No. 6, art. No. 2004765.

[13] A. Raj, M. Kumar, D.V. Singh, and A. Anshul, A critical review on transition metal dichalcogenides (TMDs): An efficiency booster for perovskite solar cells, FlatChem, 44(2024), art. No. 100629.

[14] S. Aftab, B.S. Goud, M. Mukhtar, et al., Perovskite photovoltaics with cutting-edge strategies in 2D TMDs-based interfacial layer optimization, Mater. Today Sustain., 28(2024), art. No. 100982.

[15] Zheng JH, Zhu LX, Shen ZT, et al. . Effects of the incorporation amounts of CdS and Cd(SCN₂H₄)₂Cl₂ on the performance of perovskite solar cells. Int. J. Miner. Metall. Mater., 2022, 29(2): 283

[16] S. Aftab, A. Abbas, M.Z. Iqbal, et al., Two-dimensional MXene incorporating for electron and hole transport in high-performance perovskite solar cells, Mater. Today Energy, 36(2023), art. No. 101366.

[17] Yang L, Li P, Ma JG, Zhang XT, Wang XF, Liu YC. MXenes for perovskite solar cells: Progress and prospects. J. Energy Chem., 2023, 81: 443

[18] Muduli SK, Varrla E, Kulkarni SA, et al. . 2D black phosphorous nanosheets as a hole transporting material in perovskite solar cells. J. Power Sources, 2017, 371: 156

[19] T. Liu, Y.J. Liu, M.W. Chen, et al., Fluorinated black phosphorene nanosheets with robust ambient stability for efficient and stable perovskite solar cells, Adv. Funct. Mater., 32(2022), No. 1, art. No. 2106779.

[20] Zhang CF, Ma YL, Zhang XT, et al. . Two-dimensional transition metal carbides and nitrides (MXenes): Synthesis, properties, and electrochemical energy storage applications. Energy Environ. Mater., 2020, 3(1): 29

[21] W. Li, Z.M. Wang, F. Deschler, S. Gao, R.H. Friend, and A.K. Cheetham, Chemically diverse and multifunctional hybrid organic–inorganic perovskites, Nat. Rev. Mater., 2(2017), art. No. 16099.

[22] H.L. Liu, S. Hussain, S.H.A. Jaffery, et al., Construction of perovskite solar cells and X-ray detectors using the indium selenide–carbon nanotube hybrids tuned hole transporting layer, Surf. Interfaces, 41(2023), art. No. 103234.

[23] Qiu XC, Liu Y, Li WW, Hu YY. Traps in metal halide perovskites: Characterization and passivation. Nanoscale, 2020, 12(44): 22425

[24] K.V. Seshaiah and J.H. Kim, Nature of defects and their passivation engineering for advancements in perovskite solar cells, Chem. Eng. J., 492(2024), art. No. 152370.

[25] H.J. Kim, G.S. Han, and H.S. Jung, Managing the lifecycle of perovskite solar cells: Addressing stability and environmental concerns from utilization to end-of-life, eScience, 4(2024), No. 2, art. No. 100243.

[26] Tu Q, Spanopoulos I, Yasaei P, et al. . Stretching and breaking of ultrathin 2D hybrid organic-inorganic perovskites. ACS Nano, 2018, 12(10): 10347

[27] D. Bin Kim, J.W. Lee, and Y.S. Cho, Anisotropic in situ strain-engineered halide perovskites for high mechanical flexibility, Adv. Funct. Mater., 31(2021), No. 4, art. No. 2007131.

[28] Ren GH, Han WB, Deng YY, et al. . Strategies of modifying spiro-OMeTAD materials for perovskite solar cells: A review. J. Mater. Chem. A, 2021, 9(8): 4589

[29] C.Z. Xu, S.C. Zhang, W.Q. Fan, et al., Pushing the limit of open-circuit voltage deficit via modifying buried interface in CsPbI₃ perovskite solar cells, Adv. Mater., 35(2023), No. 7, art. No. 2207172.

[30] S. Hussain, H.L. Liu, D. Vikraman, et al., Characteristics of Mo₂C–CNTs hybrid blended hole transport layer in the perovskite solar cells and X-ray detectors, J. Alloy. Compd., 885(2021), art. No. 161039.

[31] Hussain S, Liu HL, Vikraman D, et al. . Tuning of electron transport layers using MXene/metal-oxide nanocomposites for perovskite solar cells and X-ray detectors. Nanoscale, 2023, 15(16): 7329

[32] Liu HL, Hussain S, Abbas Z, et al. . Fabrication of high-performance solar cells and X-ray detectors using MoX₂@CNT nanocomposite-tuned perovskite layers. ACS Appl. Mater. Interfaces, 2022, 14(29): 33626

[33] Y. Zhao, B. Li, C.M. Tian, et al., Anhydrous organic etching derived fluorine-rich terminated MXene nanosheets for efficient and stable perovskite solar cells, Chem. Eng. J., 469(2023), art. No. 143862.

[34] Z.L. Guo, L.G. Gao, Z.H. Xu, et al., High electrical conductivity 2D MXene serves as additive of perovskite for efficient solar cells, Small, 14(2018), No. 47, art. No. 1802738.

[35] X. Liu, Z.A. Zhang, J.K. Jiang, et al., Chlorine-terminated MXene quantum dots for improving crystallinity and moisture stability in high-performance perovskite solar cells, Chem. Eng. J., 432(2022), art. No. 134382.

[36] J.K. Zhang, C.W. Huang, Y.P. Sun, and H.Z. Yu, Amino-functionalized niobium-carbide MXene serving as electron transport layer and perovskite additive for the preparation of high-performance and stable methylammonium-free perovskite solar cells, Adv. Funct. Mater., 32(2022), No. 24, art. No. 2113367.

[37] Hu T, Hu MM, Li ZJ, et al. . Covalency-dependent vibrational dynamics in two-dimensional titanium carbides. J. Phys. Chem. A, 2015, 119(52): 12977

[38] Kasimuthumaniyan S, Singh SK, Jayasankar K, Mohanta K, Mandal A. An alternate approach to synthesize TiC powder through thermal plasma processing of titania rich slag. Ceram. Int., 2016, 42(16): 18004

[39] Pawbake A, Waykar R, Jadhavar A, et al. . Wide band gap and conducting tungsten carbide (WC) thin films prepared by hot wire chemical vapor deposition (HW-CVD) method. Mater. Lett., 2016, 183: 315

[40] Xu RD, Chen H, Zhang JJ, et al. . Preparation of WC@graphene reinforced titanium diboride-based composite ceramic materials fabricated via SPS. Int. J. Appl. Ceram. Technol., 2024, 21(6): 4048

[41] Nishide D, Wakabayashi T, Sugai T, et al. . Raman spectroscopy of size-selected linear polyyne molecules C_2nH₂ (n = 4–6) encapsulated in single-wall carbon nanotubes. J. Phys. Chem. C, 2007, 111(13): 5178

[42] Hussain S, Aftab S, Abbas Z, et al. . Designing CoS₂–Mo₂C and CoS₂–W₂C hybrids for high-performance supercapacitors and hydrogen evolution reactions. Inorg. Chem. Front., 2024, 11(13): 4001

[43] S. Hussain, I. Rabani, D. Vikraman, et al., MoS₂@X₂C (X = Mo or W) hybrids for enhanced supercapacitor and hydrogen evolution performances, Chem. Eng. J., 421(2021), art. No. 127843.

[44] D. Vikraman, S.S. Patil, S. Hussain, et al., Decoration of X₂C nanoparticles on CdS nanostructures for highly efficient photocatalytic wastewater treatment under visible light, Appl. Surf. Sci., 583(2022), art. No. 152533.

[45] H. Li, S.L. Ma, L.X. Chen, and Z. Yu, Carbon-deficient titanium carbide with highly enhanced hardness, Front. Phys., 8(2020), art. No. 364.

[46] Z.J. Yao, X.H. Xia, D. Xie, et al., Enhancing ultrafast lithium ion storage of Li₄Ti₅O₁₂ by tailored TiC/C core/shell skeleton plus nitrogen doping, Adv. Funct. Mater., 28(2018), No. 31, art. No. 1802756.

[47] D. Vikraman, H.L. Liu, S. Hussain, et al., Impact of molybdenum dichalcogenides on the active and hole-transport layers for perovskite solar cells, X-ray detectors, and photodetectors, Small, 18(2022), No. 13, art. No. 2104216.

[48] Liu J, Yin XT, Guo YX, et al. . Influence of hole transport layers/perovskite interfaces on the hysteresis behavior of inverted perovskite solar cells. ACS Appl. Energy Mater., 2020, 3(7): 6391

[49] W. Tress, N. Marinova, O. Inganäs, M.K. Nazeeruddin, S.M. Zakeeruddin, and M. Graetzel, Predicting the open-circuit voltage of CH₃NH₃PbI₃ perovskite solar cells using electroluminescence and photovoltaic quantum efficiency spectra: The role of radiative and non-radiative recombination, Adv. Energy Mater., 5(2015), No. 3, art. No. 1400812.

[50] Agresti A, Pazniak A, Pescetelli S, et al. . Titanium-carbide MXenes for work function and interface engineering in perovskite solar cells. Nat. Mater., 2019, 18(11): 1228

[51] Si HN, Zhao X, Liao QL, Zhang Y. Design and tailoring of patterned ZnO nanostructures for perovskite light absorption modulation. Int. J. Miner. Metall. Mater., 2024, 31(5): 855

[52] W.H. Wang and L.M. Qi, Light management with patterned micro- and nanostructure arrays for photocatalysis, photovoltaics, and optoelectronic and optical devices, Adv. Funct. Mater., 29(2019), No. 25, art. No. 1807275.

[53] Liu XY, Tan XH, Liu ZY, et al. . Boosting the efficiency of carbon-based planar CsPbBr₃ perovskite solar cells by a modified multistep spin-coating technique and interface engineering. Nano Energy, 2019, 56: 184

[54] C.Y. Chang, M.M. Zhao, K.J. Jiang, and R.Z. Wang, Polybenzimidazole-modified perovskite films for efficient and stable planar heterojunction solar cells, Chem. Eng. J., 523(2025), art. No. 168260.

[55] Liu Y, Xu HZ, Ji SL, et al. . Thiourea derivative induced crystallization for enhanced efficiency and stability of perovskite solar cells over 25%. J. Energy Chem., 2025, 108: 109

[56] X. Xie, Z.G. Zhu, Y. Huang, et al., Multifunctional organoacyl chloride molecule for enhancing the efficiency and stability of perovskite solar cells, Chem. Eng. J., 523(2025), art. No. 168322.

[57] Wu XF, Yang TS, Che YL, et al. . Multisite-passivating molecules assisted regulation of perovskite crystallization kinetics for constructing high-efficiency and stable perovskite solar cells. J. Energy Chem., 2025, 110: 50

[58] Wu P, Zhang XY, Zhang K, et al. . Ti₂CT_x-MXene as an efficient passivation layer to regulate the vertical growth of perovskite layers and enhance the performance of solar cells. ACS Appl. Mater. Interfaces, 2025, 17(8): 12095

[59] Baek D, Park GY, Cha J, Na H, Ham DS, Kim M. Enhancing the efficiency and scalability of perovskite solar cells through pseudo-halide salt addition. J. Mater. Sci. Technol., 2023, 165: 161

[60] Li ZH, Cao JG, Yang XJ, et al. . Buried interface engineering for MAPbI3 perovskite solar cells by the novel carbon nitride synergistic strategy. ACS Appl. Mater. Interfaces, 2025, 17(15): 22860

[61] Qin ZX, Chen YT, Wang XT, Liu XM, Miao YF, Zhao YX. Incorporation of two-dimensional WSe₂ into MAPbI₃ perovskite for efficient and stable photovoltaics. J. Phys. Chem. Lett., 2021, 12(29): 6883

[62] Ding XD, Wang HX, Miao YW, et al. . Bi(trifluoromethyl) benzoic acid-assisted shallow defect passivation for perovskite solar cells with an efficiency exceeding 21%. ACS Appl. Mater. Interfaces, 2022, 14(3): 3930

[63] Han BY, Cai HK, Liu C, et al. . Bifunctional passivation of wide-bandgap perovskite solar cells via long-chain organic ammonium salts. ACS Appl. Mater. Interfaces, 2025, 17(17): 25400

[64] D.F. Xu, T. Li, Y. Han, et al., Fluorine functionalized MXene QDs for near-record-efficiency CsPbI₃ solar cell with high open-circuit voltage, Adv. Funct. Mater., 32(2022), No. 33, art. No. 2203704.

[65] Y.X. Li, D.D. Wang, L.Y. Yang, and S.G. Yin, Preparation and performance of perovskite solar cells with two dimensional MXene as active layer additive, J. Alloy. Compd., 904(2022), art. No. 163742.

[66] X. Jin, L. Yang, and X.F. Wang, Efficient two-dimensional perovskite solar cells realized by incorporation of Ti₃C₂T_x MXene as nano-dopants, Nano-Micro Lett., 13(2021), No. 1, art. No. 68.

[67] Z. Yang, J.W. Mao, B.L. He, et al., Enhanced charge extraction by dual-heteroatoms co-doped carbon nanospheres as electrode and interface modifier for carbon-based perovskite solar cells, Chem. Eng. J., 523(2025), art. No. 168258.

[68] Park BW, Kwon HW, Lee Y, et al. . Stabilization of formamidinium lead triiodide α-phase with isopropylammonium chloride for perovskite solar cells. Nat. Energy, 2021, 6(4): 419

[69] Kim M, Jeong J, Lu HZ, et al. . Conformal quantum dot-SnO₂ layers as electron transporters for efficient perovskite solar cells. Science, 2022, 375(6578): 302

[70] Y.C. Zhou, Z.Y. He, Q.L. Wei, et al., A chain entanglement gelled SnO electron transport layer for enhanced perovskite solar cell performance and effective lead capture, Adv. Mater., 37(2025), No. 8, art. No. 2416932.

[71] Blaha P, Schwarz K, Madsen GKH, Kvasnicka D, Luitz J. Wien2k: An Augmented Plane Wave Plus Local Orbitals Program for Calculating Crystal Properties, 2001, Vienna, Vienna University of Technology

[72] Schwarz K, Blaha P, Trickey SB. Electronic structure of solids with WIEN2k. Mol. Phys., 2010, 108(21–23): 3147

[73] S. Azam, M. Irfan, Z. Abbas, et al., DFT study of the electronic and optical properties of ternary chalcogenides AlX₂Te₄, Mater. Res. Express, 6(2019), No. 11, art. No. 116314.

[74] Z. Abbas, S. Hussain, S. Muhammad, S.M. Siddeeg, and J. Jung, A first-principles investigation on the structural, optoelectronic, and thermoelectric properties of pyrochlore oxides (La₂Tm₂O₇ (Tm = Hf, Zr)) for energy applications, Int. J. Mol. Sci., 23(2022), No. 23, art. No. 15266.

[75] Murnaghan FD. The compressibility of media under extreme pressures. PNAS, 1944, 30(9): 244

RIGHTS & PERMISSIONS

University of Science and Technology Beijing