Effect of Nb-V microalloying on the hot deformation behavior of medium Mn steels

Abstract

The influence of Nb-V microalloying on the hot deformation behavior and microstructures of medium Mn steel (MMS) was investigated by uniaxial hot compression tests. By establishing the constitutive equations for simulating the measured flow curves, we successfully constructed deformation activation energy (Q) maps and processing maps for identifying the region of flow instability. We concluded the following consequences of Nb-V alloying for MMS. (i) The critical strain increases and the increment diminishes with the increasing deformation temperature, suggesting that NbC precipitates more efficiently retard dynamic recrystallization (DRX) in MMS compared with solute Nb. (ii) The deformation activation energy of MMS is significantly increased and even higher than that of some reported high Mn steels, suggesting that its ability to retard DRX is greater than that of the high Mn content. (iii) The hot workability of MMS is improved by narrowing the hot processing window for the unstable flow stress, in which fine recrystallized and coarse unrecrys-tallized grains are present.

Keywords

medium manganese steel / niobium-vanadium microalloying / flow behavior / dynamic recrystallization / hot workability

References

[1] Grajcar A, Kuziak R, Zalecki W. Third generation of AHSS with increased fraction of retained austenite for the automotive industry. Arch. Civ. Mech. Eng.. 2012, 12(3): 334

[2] Hu B, Sui H, Wen QH, Wang Z, Gramlich A, Luo HW. Review on the plastic instability of medium-Mn steels for identifying the formation mechanisms of Lüders and Portevin-Le Chatelier bands. Int. J. Miner. Metall. Mater.. 2024, 31(6): 1285

[3] He BB, Hu B, Yen HW, et al. . High dislocation density-induced large ductility in deformed and partitioned steels. Science. 2017, 357(6355): 1029

[4] Li SS, Luo HW. Medium-Mn steels for hot forming application in the automotive industry. Int. J. Miner. Metall. Mater.. 2021, 28(5): 741

[5] Zhao JW, Jiang ZY. Thermomechanical processing of advanced high strength steels. Prog. Mater. Sci.. 2018, 94: 174

[6] Wang YJ, Zhao S, Song RB, Hu B. Hot ductility behavior of a Fe-0.3C-9Mn-2Al medium Mn steel. Int. J. Miner. Metall. Mater.. 2021, 28(3): 422

[7] Quan GZ, Wang X, Li YL, Zhang L. Analytical descriptions of dynamic softening mechanisms for Ti-13Nb-13Zr biomedical alloy in single phase and two phase regions. Arch. Metall. Mater.. 2017, 62(4): 2029

[8] Sakai T, Belyakov A, Kaibyshev R, Miura H, Jonas JJ. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions. Prog. Mater. Sci.. 2014, 60: 130

[9] Han J, Lee SJ, Jung JG, Lee YK. The effects of the initial martensite microstructure on the microstructure and tensile properties of intercritically annealed Fe-9Mn-0.05C steel. Acta Mater.. 2014, 78: 369

[10] Feng HB, Li SH, Wang KX, et al. . Effect of deformation parameters on the austenite dynamic recrystallization behavior of a eutectoid pearlite rail steel. Int. J. Miner. Metall. Mater.. 2024, 31(5): 833

[11] X.Y. Sun, M. Zhang, Y. Wang, Y.Y. Sun, and Y.H. Wang, Kinetics and numerical simulation of dynamic recrystallization behavior of medium Mn steel in hot working, Steel Res. Int., 91(2020), No. 7, art. No. 1900675.

[12] Liu XZ, Sun Y, Zhang XY, Li HP, Li ZC, He LF. Thermal deformation behavior and microstructure evolution of Fe-8.5Mn-1.5Al light-weight medium manganese steel. J. Mater. Res. Technol.. 2023, 26: 605

[13] Niu T, Kang YL, Gu HW, Yin YQ, Qiao ML, Jiang JX. Effect of Nb on the dynamic recrystallization behavior of high-grade pipeline steels. Int. J. Miner. Metall. Mater.. 2010, 17(6): 742

[14] Chen BH, Yu H. Hot ductility behavior of V-N and V-Nb microalloyed steels. Int. J. Miner. Metall. Mater.. 2012, 19(6): 525

[15] Y. Luo, H.Z. Lu, N. Min, W. Li, and X.J. Jin, Effect of Mo and Nb on mechanical properties and hydrogen embrittlement of hot-rolled medium-Mn steels, Mater. Sci. Eng. A, 844(2022), art. No. 143108.

[16] R.S. Varanasi, B. Gault, and D. Ponge, Effect of Nb micro-alloying on austenite nucleation and growth in a medium manganese steel during intercritical annealing, Acta Mater., 229(2022), art. No. 117786.

[17] Y.S. Zhu, B. Hu, and H.W. Luo, Influence of Nb and V on microstructure and mechanical properties of hot-rolled medium Mn steels, Steel Res. Int., 89(2018), No. 9, art. No. 1700389.

[18] P.P. Singh, S. Ghosh, and S. Mula, Flow stress modeling and microstructural characteristics of a low carbon Nb-V microal-loyed steel, Mater. Today Commun., 30(2022), art. No. 103156.

[19] Tsuji N, Matsubara Y, Saito Y. Dynamic recrystallization of ferrite in interstitial free steel. Scripta. Mater.. 1997, 37(4): 477

[20] Wang XH, Liu ZB, Luo HW. Hot deformation characterization of ultrahigh strength stainless steel through processing maps generated using different instability criteria. Mater. Charact.. 2017, 131: 480

[21] Liu KM, Jiang ZY, Zhou HT, Lu DP, Atrens A, Yang YL. Effect of heat treatment on the microstructure and properties of deformation-processed Cu-7Cr in situ composites. J. Mater. Eng. Perform.. 2015, 24(11): 4340

[22] Yin DL, Zhang KF, Wang GF, Han WB. Warm deformation behavior of hot-rolled AZ31 Mg alloy. Mater. Sci. Eng. A. 2005, 392(1–2): 320

[23] Poliak EI, Jonas JJ. A one-parameter approach to determining the critical conditions for the initiation of dynamic recrystallization. Acta Mater.. 1996, 44(1): 127

[24] Richardson GJ, Sellars CM, Tegart WJM. Recrysta-llization during creep of nickel. Acta Metall.. 1966, 14(10): 1225

[25] Sellars CM, Tegart WJMcG. Hot workability. Int. Metall. Rev.. 1972, 17(1): 1

[26] Mirzadeh H, Cabrera JM, Prado JM, Najafizadeh A. Hot deformation behavior of a medium carbon microalloyed steel. Mater. Sci. Eng. A. 2011, 528(10–11): 3876

[27] Prasad YVRK, Gegel HL, Doraivelu SM, et al. . Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242. Metall. Trans. A. 1984, 15(10): 1883

[28] Mirzadeh H, Najafizadeh A, Moazeny M. Flow curve analysis of 17-4 PH stainless steel under hot compression test. Metall. Mater. Trans. A. 2009, 40(12): 2950

[29] McQueen HJ, Ryan ND. Constitutive analysis in hot working. Mater. Sci. Eng. A. 2002, 322(1–2): 43

[30] McQueen HJ, Bourell DL. Hot workability of metals and alloys. JOM. 1987, 39(9): 28

[31] Zhang JQ, Di HS, Wang XY, Cao Y, Zhang JC, Ma TJ. Constitutive analysis of the hot deformation behavior of Fe-23Mn-2Al-0.2C twinning induced plasticity steel in consideration of strain. Mater. Des.. 2013, 44: 354

[32] Li DJ, Feng YR, Yin ZF, et al. . Hot deformation behavior of an austenitic Fe-20Mn-3Si-3Al transformation induced plasticity steel. Mater. Des.. 2012, 34: 713

[33] McQueen HJ, Yue S, Ryan ND, Fry E. Hot working characteristics of steels in austenitic state. J. Mater. Process. Technol.. 1995, 53(1–2): 293

[34] Reyes-Calderón F, Mejía I, Cabrera JM. Hot deformation activation energy (Q_HW) of austenitic Fe-22Mn-1.5Al-1.5Si-0.4C TWIP steels microalloyed with Nb, V, and Ti. Mater. Sci. Eng. A. 2013, 562: 46

[35] Momeni A. The physical interpretation of the activation energy for hot deformation of Ni and Ni-30Cu alloys. J. Mater. Res.. 2016, 31(8): 1077

[36] Samantaray D, Mandal S, Kumar V, Albert SK, Bhaduri AK, Jayakumar T. Optimization of processing parameters based on high temperature flow behavior and microstructural evolution of a nitrogen enhanced 316L(N) stainless steel. Mater. Sci. Eng. A. 2012, 552: 236

[37] Wang S, Hou LG, Luo JR, Zhang JS, Zhuang LZ. Characterization of hot workability in AA 7050 aluminum alloy using activation energy and 3-D processing map. J. Mater. Process. Technol.. 2015, 225: 110

[38] Prasad YVRK, Seshacharyulu T. Modelling of hot deformation for microstructural control. Int. Mater. Rev.. 1998, 43(6): 243

[39] Sun Y, Zeng WD, Zhao YQ, Zhang XM, Shu Y, Zhou YG. Research on the hot deformation behavior of Ti40 alloy using processing map. Mater. Sci. Eng. A. 2011, 528(3): 1205

RIGHTS & PERMISSIONS

University of Science and Technology Beijing