Potassium thiocyanate additive for PEDOT:PSS layer to fabricate efficient tin-based perovskite solar cells

Abstract

The commercialized poly(3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) is usually used as hole transport layers (HTLs) in tin-based perovskite solar cells (TPSCs). However, the further development has been restricted due to the acidity that could damage the stability of TPSCs. Although the PEDOT:PSS solution can be diluted by water to decrease acidity and reduce the cost of device fabrication, the electrical conductivity will decrease obviously in diluted PEDOT:PSS solution. Herein, potassium thiocyanate (KSCN) is selected to regulate the properties of PEDOT:PSS HTLs from the diluted PEDOT:PSS aqueous solution by water with a volume ratio of 1:1 to prepare efficient TPSCs. The effect of KSCN addition on the structure and photoelectrical properties of PEDOT:PSS HTLs and TPSCs have been systematically studied. At the optimal KSCN concentration, the TPSCs based on KSCN-doped PEDOT:PSS HTLs (KSCN-PSCs) demonstrate the champion power conversion efficiency (PCE) of 8.39%, while the reference TPSCs only show a champioan PCE of 6.70%. The further analysis demonstrates that the KSCN additive increases the electrical conductivity of HTLs prepared by the diluted PEDOT:PSS solution, improves the microstructure of perovskite film, and inhibits carrier recombination in TPSCs, leading to the reduced hysteresis effect and enhanced PCE in KSCN-PSCs. This work gives a low-cost and practical strategy to develop a high-quality PEDOT:PSS HTLs from diluted PE-DOT:PSS aqueous solution for efficient TPSCs.

Keywords

potassium thiocyanate / diluted PEDOT:PSS solution / tin-based perovskite solar cells / photovoltaic performance

References

[1] B.B. Yu, Z.H. Chen, Y.D. Zhu, et al., Heterogeneous 2D/3D tin-halides perovskite solar cells with certified conversion efficiency breaking 14%, Adv. Mater., 33(2021), No. 36, art. No. e2102055.

[2] Diau EWG, Jokar E, Rameez M. Strategies to improve performance and stability for tin-based perovskite solar cells. ACS Energy Lett., 2019, 4(8): 1930.

[3] H. Elbohy, B. Bahrami, S. Mabrouk, et al., Tuning hole transport layer using urea for high-performance perovskite solar cells, Adv. Funct. Mater., 29(2019), No. 47, art. No. 1806740.

[4] Yu W, Wang KX, Guo B, et al. Effect of ultraviolet absorptivity and waterproofness of poly(3,4-ethylenedioxy-thiophene) with extremely weak acidity, high conductivity on enhanced stability of perovskite solar cells. J. Power Sources, 2017, 358, 29.

[5] N. Cheng, Z. Liu, Z. Yu, et al., High performance inverted perovskite solar cells using PEDOT:PSS/KCl hybrid hole transporting layer, Org. Electron., 98(2021), art. No. 106298.

[6] Palumbiny CM, Heller C, Schaffer CJ, et al. Molecular reorientation and structural changes in cosolvent-treated highly conductive PEDOT:PSS electrodes for flexible indium tin oxide-free organic electronics. J. Phys. Chem. C, 2014, 118(25): 13598.

[7] Cao JP, Tai QD, You P, et al. Enhanced performance of tin-based perovskite solar cells induced by an ammonium hypophosphite additive. J. Mater. Chem. A, 2019, 7(46): 26580.

[8] Tai QD, Guo XY, Tang GQ, et al. Antioxidant grain passivation for air-stable tin-based perovskite solar cells. Angew. Chem. Int. Ed., 2019, 58(3): 806.

[9] W.W. Li, N. Cheng, Y. Cao, et al., Boost the performance of inverted perovskite solar cells with PEDOT:PSS/graphene quantum dots composite hole transporting layer, Org. Electron., 78(2020), art. No. 105575.

[10] C. Wang, C. Zhang, S. Tong, et al., Energy level and thickness control on PEDOT:PSS layer for efficient planar heterojunction perovskite cells, J. Phys. D: Appl. Phys., 51(2018), No. 2, art. No. 025110.

[11] Liu X, Wang YB, Xie FX, Yang XD, Han LY. Improving the performance of inverted formamidinium tin iodide perovskite solar cells by reducing the energy-level mismatch. ACS Energy Lett., 2018, 3, 1116.

[12] Y.H. Chen, K. Cao, Y.F. Cheng, et al., P-type dopants as dual function interfacial layer for efficient and stable tin perovskite solar cells, Sol. RRL, 5(2021), No. 5, art. No. 2100068.

[13] Zhang XH, Hao Y, Li SQ, et al. Multifunction sandwich structure based on diffusible 2-chloroethylamine for high-efficiency and stable tin-lead mixed perovskite solar cells. J. Phys. Chem. Lett., 2022, 13(1): 118.

[14] J.W. Chen, X.H. Zhao, Y.F. Cheng, et al., Hydroxyl-rich d-sorbitol to address transport layer/perovskite interfacial issues toward highly efficient and stable 2D/3D tin-based perovskite solar cells, Adv. Opt. Mater., 9(2021), No. 22, art. No. 2100755.

[15] Z. Cao, S. Wang, W. Zhu, L. Ding, and F. Hao, Minimizing the voltage deficit of tin halide perovskite solar cells with hydroxyurea-doped PEDOT:PSS, Sol. RRL, 7(2023), No. 2, art. No. 2200889.

[16] X. Huang, K. Wang, C. Yi, T. Meng, and X. Gong, Efficient perovskite hybrid solar cells by highly electrical conductive PE-DOT:PSS hole transport layer, Adv. Energy Mater., 6(2016), No. 3, art. No. 1501773.

[17] Hu W, Xu CY, Niu LB, et al. High open-circuit voltage of 1.134 V for inverted planar perovskite solar cells with sodium citrate-doped PEDOT: PSS as a hole transport layer. ACS Appl. Mater. Interfaces, 2019, 11(24): 22021.

[18] W. Li, H.X. Wang, X.F. Hu, et al., Sodium benzenesulfonate modified poly(3,4-Ethylenedioxythiophenepolystyrene sulfonate with improved wettability and work function for efficient and stable perovskite solar cells, Sol. RRL, 5(2021), No. 1, art. No. 2000573.

[19] J.J. Cao, Y.H. Lou, W.F. Yang, et al., Multifunctional potassium thiocyanate interlayer for eco-friendly tin perovskite indoor and outdoor photovoltaics, Chem. Eng. J., 433(2022), art. No. 133832.

[20] S. Zhong, Z.X. Li, C.Q. Zheng, et al., Guanidine thiocyanate-induced high-quality perovskite film for efficient tin-based perovskite solar cells, Sol. RRL, 6(2022), No. 7, art. No. 2200088.

[21] Ran CX, Gao WY, Li JR, et al. Conjugated organic cations enable efficient self-healing FASnI₃ solar cells. Joule, 2019, 3(12): 3072.

[22] Cao K, Cheng YF, Chen JW, et al. Regulated crystallization of FASnI₃ films through seeded growth process for efficient tin perovskite solar cells. ACS Appl. Mater. Interfaces, 2020, 12(37): 41454.

[23] Y. Su, J. Yang, G.L. Liu, et al., Acetic acid-assisted synergistic modulation of crystallization kinetics and inhibition of Sn²⁺ oxidation in tin-based perovskite solar cells, Adv. Funct. Mater., 32(2021), No. 12, art. No. 2109631.

[24] Xia YJ, Sun K, Ouyang JY. Highly conductive poly(3, 4-ethylenedioxythiophene): poly(styrene sulfonate) films treated with an amphiphilic fluoro compound as the transparent electrode of polymer solar cells. Energy Environ. Sci., 2012, 5(1): 5325.

[25] Han WB, Ren GH, Liu JM, et al. Recent progress of inverted perovskite solar cells with a modified PEDOT:PSS hole transport layer. ACS Appl. Mater. Interfaces, 2020, 12(44): 49297.

[26] Wu F, Yan KR, Wu HT, et al. Tuning interfacial chemical interaction for high-performance perovskite solar cell with PE-DOT:PSS as hole transporting layer. J. Mater. Chem. A, 2021, 9(26): 14920.

[27] Z.W. Gao, Y. Wang, D. Ouyang, et al., Triple interface passivation strategy enabled efficient and stable inverted perovskite solar cells, Small Methods, 4(2020), No. 12, art. No. 2000478.

[28] G.Z. Xia, B.Y. Huang, Y. Zhang, et al., Nanoscale insights into photovoltaic hysteresis in triple-cation mixed-halide perovskite: Resolving the role of polarization and ionic migration, Adv. Mater., 31(2019), No. 36, art. No. e1902870.

[29] Aftab A, Ahmad MI. A review of stability and progress in tin halide perovskite solar cell. Sol. Energy, 2021, 216, 26.

[30] M. Ismail, Z. Wu, H.L. You, Y.M. Jia, J.C. Xia, and Y.J. Wang, Photovoltaic effect of “ferroelectric” bananas, Europhys. Lett., 125(2019), No. 4, art. No. 47001.

[31] Xu XL, Xiao LB, Zhao J, et al. Molecular ferroelectrics-driven high-performance perovskite solar cells. Angew. Chem. Int. Ed., 2020, 59(45): 19974.

[32] Yin GN, Ma JX, Jiang H, et al. Enhancing efficiency and stability of perovskite solar cells through Nb-doping of TiO₂ at low temperature. ACS Appl. Mater. Interfaces, 2017, 9(12): 10752.

[33] Meng XY, Wu TH, Liu X, et al. Highly reproducible and efficient FASnI₃ perovskite solar cells fabricated with volatilizable reducing solvent. J. Phys. Chem. Lett., 2020, 11(8): 2965.

[34] Liu XY, Tan XH, Liu ZY, et al. Boosting the efficiency of carbon-based planar CsPbBr₃ perovskite solar cells by a modified multistep spin-coating technique and interface engineering. Nano Energy, 2019, 56, 184.

[35] L. Chen, C.W. Li, Y.M. Xian, et al., Incorporating potassium citrate to improve the performance of tin-lead perovskite solar cells, Adv. Energy Mater., 13(2023), No. 32, art. No. 2301218.

[36] Zhou Y, Zhang ZB, Cai YY, et al. High performance planar perovskite solar cells based on CH₃NH₃PbI_3−x(SCN)_x perovskite film and SnO₂ electron transport layer prepared in ambient air with 70% humility. Electrochim. Acta, 2018, 260, 468.

[37] C. Chen, Y. Jiang, Y.C. Feng, et al., Understanding the effect of antisolvent on processing window and efficiency for large-area flexible perovskite solar cells, Mater. Today Phys., 21(2021), art. No. 100565.

[38] C. Chen, Y. Jiang, J.L. Guo, et al., Solvent-assisted low-temperature crystallization of SnO₂ electron-transfer layer for high-efficiency planar perovskite solar cells, Adv. Funct. Mater., 29(2019), No. 30, art. No. 1900557.

[39] Kim M, Choi IW, Choi SJ, et al. Enhanced electrical properties of Li-salts doped mesoporous TiO₂ in perovskite solar cells. Joule, 2021, 5(3): 659.