Effect of Zn content on microstructure, mechanical properties and thermal conductivity of extruded Mg-Zn-Ca-Mn alloys

Abstract

Mg-Zn-Ca-Mn series alloys are developed as promising candidates of 5G communication devices with excellent thermal conductivities, great ductility, and acceptable strength. In present paper, Mg-xZn-0.4Ca-0.2Mn (x = 2wt%, 4wt%, 6wt%) alloys were prepared by a near-solidus extrusion and the effect of Zn content on mechanical and thermal properties were investigated. The results showed that the addition of minor Ca led to the formation of Ca₂Mg₆Zn₃ eutectic phase at grain boundaries. A type of bimodal microstructure occurred in the as-extruded alloys, where elongated coarse deformed grains were embedded in refined recrystallized grains matrix. Correspondingly, both yield strength and ductility of the alloys were significantly enhanced after extrusion due to the great grain refinement. Specially, higher Zn content led to the increment in yield strength and a slight reduction in elongation due to the larger fractions of second phase particles. The room temperature thermal conductivity of as-extruded alloys was also improved compared with that of as-cast counterparts. The increment of Zn content decreased the thermal conductivity of both as-cast and as-extruded alloys, which was due to the increased second phase fraction and solution atoms in the matrix, that hindering the motion of electrons. The as-extruded Mg-2Zn-0.4Ca-0.2Mn (wt%) alloy exhibited the highest elongation of 27.7% and thermal conductivity of 139.2 W/(mK), combined with an acceptable ultimate tensile strength of 244.0 MPa. The present paper provides scientific guidance for the preparation of lightweight materials with high ductility and high thermal conductivity.

Keywords

Mg-Zn-Ca-Mn alloys / microstructure / mechanical properties / thermal conductivity / extrusion

References

[1] Mazloum A, Oddone V, Reich S, Sevostianov I. Connection between strength and thermal conductivity of metal matrix composites with uniform distribution of graphite flakes. Int. J. Eng. Sci., 2019, 139, 70.

[2] Song JF, She J, Chen DL, Pan FS. Latest research advances on magnesium and magnesium alloys worldwide. J. Magnes. Alloys, 2020, 8(1): 1.

[3] Zeng XQ, Wang J, Ying T, Ding WJ. Recent progress on thermal conductivity of magnesium and its alloys. Acta Metall. Sin., 2022, 58(4): 400.

[4] Yuan JW, Li T, Li XG, et al. Homogenizing heat treatment and thermal conductivity of Mg-4Zn-1Mn magnesium alloy. Trans. Mater. Heat Treat., 2012, 33(4): 27.

[5] Li SB, Yang XY, Hou JT, Du WB. A review on thermal conductivity of magnesium and its alloys. J. Magnes. Alloys, 2020, 8(1): 78.

[6] X. Du, W.B. Du, Z.H. Wang, K. Liu, and S.B. Li, Simultaneously improved mechanical and thermal properties of Mg-Zn-Zr alloy reinforced by ultra-low content of graphene nanoplatelets, Appl. Surf. Sci., 536(2021), art. No. 147791.

[7] Mater. Res., 2019, 22(6) art. No. e20190430

[8] Yuan JW, Zhang K, Zhang XH, et al. Thermal characteristics of Mg-Zn-Mn alloys with high specific strength and high thermal conductivity. J. Alloys Compd., 2013, 578, 32.

[9] Li HC, Zhu XR, Zhang Y, et al. Microstructure, thermal conductivity and mechanical properties of Mg-Zn-Mn-Y quaternary alloys. JOM, 2020, 72(4): 1580.

[10] Zhang WP, Ma ML, Yuan JW, et al. Microstructure and thermophysical properties of Mg-2Zn-xCu alloys. Trans. Nonferrous Met. Soc. China, 2020, 30(7): 1803.

[11] P. Duley, S. Sanyal, T.K. Bandyopadhyay, and S. Mandal, Homogenization-induced age-hardening behavior and room temperature mechanical properties of Mg-4Zn-0.5Ca-0.16Mn (wt%) alloy, Mater. Des., 164(2019), art. No. 107554.

[12] Du YZ, Zheng MY, Xu C, et al. Microstructures and mechanical properties of as-cast and as-extruded Mg-4.50Zn-1.13Ca (wt%) alloys. Mater. Sci. Eng. A, 2013, 576, 6.

[13] Kim B, Hong CH, Kim JC, et al. Factors affecting the grain refinement of extruded Mg-6Zn-0.5Zr alloy by Ca addition. Scripta Mater., 2020, 187, 24.

[14] Xie T, Wang YF, Liu K, Li SB, Zhu XM, Du WB. Microstructure and thermal conductivity of Mg-4Zn-xCa alloys. Shanghai Met., 2022, 44(4): 1.

[15] X. Chen, D.F. Zhang, J.Y. Xu, et al., Improvement of mechanical properties of hot extruded and age treated Mg-Zn-Mn-Ca alloy through Sn addition, J. Alloys Compd., 850(2021), art. No. 156711.

[16] L.Q. Zhao, C. Wang, J.C. Chen, et al., Development of weak-textured and high-performance Mg-Zn-Ca alloy sheets based on Zn content optimization, J. Alloys Compd., 849(2020), art. No. 156640.

[17] Rong W, Zhang Y, Wu YJ, et al. The role of bimodal-grained structure in strengthening tensile strength and decreasing yield asymmetry of Mg-Gd-Zn-Zr alloys. Mater. Sci. Eng. A, 2019, 740–741, 262.

[18] Jia LY, Du WB, Fu JL, et al. Obtaining ultra-high strength and ductility in a Mg-Gd-Er-Zn-Zr alloy via extrusion, pre-deformation and two-stage aging. Acta Metall. Sin. (Engl. Lett.), 2021, 34(1): 39.

[19] Fu W, Dang PF, Guo SW, et al. Heterogeneous fiberous structured Mg-Zn-Zr alloy with superior strength-ductility synergy. J. Mater. Sci. Technol., 2023, 134, 67.

[20] Sitdikov O, Garipova R, Avtokratova E, Mukhametdinova O, Markushev M. Effect of temperature of isothermal multidirectional forging on microstructure development in the Al-Mg alloy with nano-size aluminides of Sc and Zr. J. Alloys Compd, 2018, 746, 520.

[21] Lee SJ, Kim YJ, Lee JH, Park SH. Effect of rolling temperature on the microstructural characteristics of highspeed-rolled Mg alloy with initial non-basal texture. Korean J. Met. Mater., 2019, 57(8): 482.

[22] Yamasaki M, Kawamura Y. Thermal diffusivity and thermal conductivity of Mg-Zn-rare earth element alloys with long-period stacking ordered phase. Scripta Mater., 2009, 60(4): 264.

[23] Wang C, Luo TJ, Liu YT, Lin T, Yang YS. Microstructure and mechanical properties of Mg-5Zn-3.5Sn-1Mn-0.5Ca-0.5Cu alloy. Mater. Charact., 2019, 147, 406.

[24] Materials, 2019, 12(19) art. No. 3102

[25] Wang YF, Zhang F, Wang YT, et al. Effect of Zn content on the microstructure and mechanical properties of Mg-Gd-Y-Zr alloys. Mater. Sci. Eng. A, 2019, 745, 149.

[26] Wang YN, Huang JC. Texture analysis in hexagonal materials. Mater. Chem. Phys., 2003, 81(1): 11.

[27] Wang CM, Chen YG, Xiao SF. Situation of research and development of thermal conductive magnesium alloys. Rare Met. Mater. Eng., 2015, 44(10): 2596.

[28] Zhong LP, Peng J, Li M, Wang YJ, Lu Y, Pan FS. Effect of Ce addition on the microstructure, thermal conductivity and mechanical properties of Mg-0.5Mn alloys. J. Alloys Compd, 2016, 661, 402.

[29] Zhong L, Peng J, Sun Y, Wang Y, Lu Y, Pan F. Microstructure and thermal conductivity of as-cast and as-extruded binary Mg-Mn alloys. Mater. Sci. Technol., 2017, 33(1): 92.

[30] J.T. Hou, W.B. Du, Z.H. Wang, S.B. Li, K. Liu, and X. Du, Combination of enhanced thermal conductivity and strength of MWCNTs reinforced Mg-6Zn matrix composite, J. Alloys Compd, 838(2020), art. No. 155573.

[31] Ying T, Chi H, Zheng MY, Li ZT, Uher C. Low-temperature electrical resistivity and thermal conductivity of binary magnesium alloys. Acta Mater., 2014, 80, 288.

[32] Yang K, Pan HC, Du S, et al. Low-cost and high-strength Mg-Al-Ca-Zn-Mn wrought alloy with balanced ductility. Int. J. Miner. Metall. Mater., 2022, 29(7): 1396.