Understanding the superior mechanical properties of Mg–3Al–Zn alloy sheets: Role of multi-type unique textures

Abstract

Mg–3Al–1Zn (AZ31) sheets were produced by transverse gradient extrusion (TGE) process. The flow behavior and dynamic recrystallization during extrusion were systematically analyzed. The microstructures, textures, and mechanical behavior of extruded AZ31 sheet were also analyzed and compared with conventional extruded (CE) sheet. The results showed that fine grain structure and multi-type unique textures were formed in TGE sheet because of the generation of extra flow velocity along transverse direction (TD) and flow velocity gradient along extrusion direction (ED) during extrusion. The basal poles gradually deviated away normal direction (ND) from edge to center of the TGE sheet along TD, and the largest inclination angle at center region reached around 65°. Furthermore, the basal poles inclined from ED to TD 40°-63°, except for the center region of TGE sheet. The TGE sheet presented higher ductility and strain hardening exponent (n-value), but lower yield strength and Lankford value (r-value) in comparison with the CE sheet. Both the basal <a> slip and tensile twins were easy to be activated during deformation, and the largest elongation of 41% and the lowest yield strength of 86.5 MPa were obtained for the ED-center sample in the TGE sheet.

Keywords

transverse gradient extrusion / multi-type unique textures / mechanical properties

References

[1] N. Li, C. Wang, M.A. Monclús, L. Yang, and J.M. Molina-Aldareguia, Solid solution and precipitation strengthening effects in basal slip, extension twinning and pyramidal slip in Mg−Zn alloys, Acta Mater., 221(2021), art. No. 117374.

[2] Liu FY, Xin RL, Zhang MX, Pérez-Prado MT, Liu Q. Evaluating the orientation relationship of prismatic precipitates generated by detwinning in Mg alloys. Acta Mater., 2020, 195, 263.

[3] Hao JQ, Zhang JS, Wang HX, Cheng WL, Bai Y. Microstructure and mechanical properties of Mg−Zn−Y−Mn magnesium alloys with different Zn/Y atomic ratio. J. Mater. Res. Technol., 2022, 19, 1650.

[4] Koltygin AV, Bazhenov VE, Plisetskaya IV, et al. Influence of Zr and Mn additions on microstructure and properties of Mg−2.5wt%Cu−Xwt%Zn (X = 2.5, 5 and 6.5) alloys. Int. J. Miner. Metall. Mater., 2022, 29(9): 1733.

[5] M.Z. Bian, X.S. Huang, and Y. Chino, Substantial improvement in cold formability of concentrated Mg−Al−Zn−Ca alloy sheets by high temperature final rolling, Acta Mater., 220(2021), art. No. 117328.

[6] J. Zheng, Z. Chen, Z.M. Yan, Z.M. Zhang, Q. Wang, and Y. Xue, Preparation of ultra-high strength Mg−Gd−Y−Zn−Zr alloy by pre-ageing treatment prior to extrusion, J. Alloys Compd., 894(2022), art. No. 162490.

[7] Pang H, Bao J, Li QA, et al. Effect of Sm on microstructures and mechanical properties of Mg−Gd(−Sm)−Zr alloys by hot extrusion and aging treatment. J. Mater. Res. Technol., 2022, 19, 3877.

[8] Z.K. Deng, X.P. Li, S.Z. Wang, X.H. Li, D.X. Chen, and X.F. Xiao, Texture tailoring of a cold-rolled Mg−Zn−Gd alloy by electropulse treatment: The effect of electropulse and Gd element, Mater. Charact., 190(2022), art. No. 112046.

[9] Zhang Z, Zhang JH, Wang J, et al. Toward the development of Mg alloys with simultaneously improved strength and ductility by refining grain size via the deformation process. Int. J. Miner. Metall. Mater., 2021, 28(1): 30.

[10] Tsuru T, Somekawa H, Chrzan DC. Interfacial segregation and fracture in Mg-based binary alloys: Experimental and first-principles perspective. Acta Mater., 2018, 151, 78.

[11] Koike J, Kobayashi T, Mukai T, et al. The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys. Acta Mater., 2003, 51(7): 2055.

[12] Zhao J, Jiang B, Song Y, et al. Simultaneous improvement of strength and ductility by Mn addition in extruded Mg−Gd−Zn alloy. Trans. Nonferrous Met. Soc. China, 2022, 32(5): 1460.

[13] Wang Y, Choo H. Influence of texture on Hall-Petch relationships in an Mg alloy. Acta Mater., 2014, 81, 83.

[14] Basu S, Dogan E, Kondori B, Karaman I, Benzerga AA. Towards designing anisotropy for ductility enhancement: A theory-driven investigation in Mg-alloys. Acta Mater., 2017, 131, 349.

[15] Zhang DD, Liu CM, Jiang SN, Wan YC, Chen ZY. Effects of trace Ag on precipitation behavior and mechanical properties of extruded Mg−Gd−Y−Zr alloys. Trans. Nonferrous Met. Soc. China, 2021, 31(11): 3394.

[16] Y.J. Ma, C.M. Liu, S.N. Jiang, Y.C. Wan, and Z.Y. Chen, Microstructure, mechanical properties and damping capacity of as-extruded Mg−1.5Gd alloys containing rare-earth textures, Mater. Charact., 189(2022), art. No. 111969.

[17] Nie KB, Wang XJ, Deng KK, Xu FJ, Wu K, Zheng MY. Microstructures and mechanical properties of AZ91 magnesium alloy processed by multidirectional forging under decreasing temperature conditions. J. Alloys Compd., 2014, 617, 979.

[18] Pérez-Prado M, del Valle JA, Ruano OA. Achieving high strength in commercial Mg cast alloys through large strain rolling. Mater. Lett., 2005, 59(26): 3299.

[19] X. Che, B.B. Dong, Q. Wang, et al., The effect of processing parameters on the microstructure and texture evolution of a cup-shaped AZ80 Mg alloy sample manufactured by the rotating backward extrusion, J. Alloys Compd., 854(2021), art. No. 156264.

[20] Kang JW, Sun XF, Deng KK, Xu FJ, Zhang X, Bai Y. High strength Mg−9Al serial alloy processed by slow extrusion. Mater. Sci. Eng. A, 2017, 697, 211.

[21] Xu J, Jiang B, Kang YH, et al. Tailoring microstructure and texture of Mg−3Al−1Zn alloy sheets through curve extrusion process for achieving low planar anisotropy. J. Mater. Sci. Technol., 2022, 113, 48.

[22] Jafari H, Tehrani AHM, Heydari M. Effect of extrusion process on microstructure and mechanical and corrosion properties of biodegradable Mg−5Zn−1.5Y magnesium alloy. Int. J. Miner. Metall. Mater., 2022, 29(3): 490.

[23] X. Zhao, S.C. Li, Y.S. Zheng, et al., The microstructure evolution, texture weakening mechanism and mechanical properties of AZ80 Mg alloy processed by repetitive upsetting-extrusion with reduced deformation temperature, J. Alloys Compd., 883(2021), art. No. 160871.

[24] X. Li, C. Liu, J.S. Wang, and C. Zhang, Tailoring the strength and formability of Mg alloys through rare earth element additions (Gd and Dy) and dynamic recrystallizations, Mater. Today Commun., 28(2021), art. No. 102627.

[25] Imandoust A, Barrett CD, Al-Samman T, Inal KA, Kadiri HE. A review on the effect of rare-earth elements on texture evolution during processing of magnesium alloys. J. Mater. Sci., 2017, 52(1): 1.

[26] Zhou G, Yang Y, Sun L, et al. Tailoring the microstructure, mechanical properties and damping capacities of Mg−4Li−3Al−0.3Mn alloy via hot extrusion. J. Mater. Res. Technol., 2022, 19, 4197.

[27] Fan WX, Bai Y, Li GY, Chang XY, Hao H. Enhanced mechanical properties and formability of hot-rolled Mg−Zn−Mn alloy by Ca and Sm alloying. Trans. Nonferrous Met. Soc. China, 2022, 32(4): 1119.

[28] T. Nakata, C. Xu, and S. Kamado, Formation of anomalous twinning and its effect on texture development in a cold-rolled Mg−Zn−Ca alloy sheet, Mater. Charact., 181(2021), art. No. 111507.

[29] Zhao J, Jiang B, Wang QH, et al. Effects of Li addition on the microstructure and tensile properties of the extruded Mg−1Zn−xLi alloy. Int. J. Miner. Metall. Mater., 2022, 29(7): 1380.

[30] Xu J, Song JF, Jiang B, et al. Effect of effective strain gradient on texture and mechanical properties of Mg-3Al-1Zn alloy sheets produced by asymmetric extrusion. Mater. Sci. Eng. A, 2017, 706, 172.

[31] Wang QH, Song JF, Jiang B, et al. An investigation on microstructure, texture and formability of AZ31 sheet processed by asymmetric porthole die extrusion. Mater. Sci. Eng. A, 2018, 720, 85.

[32] Xu J, Liu WJ, Jiang B, et al. Forming novel texture and enhancing the formability in Mg−3Al−Zn alloy sheets fabricated by transverse gradient extrusion. J. Mater. Res. Technol., 2022, 18, 3143.

[33] Yu ZJ, Xu C, Meng J, Zhang XH, Kamado S. Microstructure evolution and mechanical properties of as-extruded Mg−Gd−Y−Zr alloy with Zn and Nd additions. Mater. Sci. Eng. A, 2018, 713, 234.

[34] Zhao CY, Chen XH, Pan FS, Gao SY, Zhao D, Liu XF. Effect of Sn content on strain hardening behavior of as-extruded Mg−Sn alloys. Mater. Sci. Eng. A, 2018, 713, 244.

[35] Kang Q, Jiang HT, Zhang Y, Xu Z, Li H, Xia ZH. Effect of various Ca content on microstructure and fracture toughness of extruded Mg−2Zn alloys. J. Alloys Compd., 2018, 742, 1019.

[36] Y. Liu, J.B. Wen, H. Li, and J.G. He, Effects of extrusion parameters on the microstructure, corrosion resistance, and mechanical properties of biodegradable Mg−Zn−Gd−Y−Zr alloy, J. Alloys Compd., 891(2022), art. No. 161964.

[37] L. Yan, Z.M. Zhang, Y. Xue, J. Xu, B.B. Dong, and X.B. Li, Effect of rotating shear extrusion on the microstructure, texture evolution and mechanical properties of Mg−Gd−Y−Zn−Zr alloy, J. Alloys Compd., 906(2022), art. No. 164406.

[38] Mináik P, Král R, Čížek J, Chmelík F. Effect of different c/a ratio on the microstructure and mechanical properties in magnesium alloys processed by ECAP. Acta Mater., 2016, 107, 83.

[39] Hofstetter J, Rüedi S, Baumgartner I, et al. Processing and microstructure-property relations of high-strength low-alloy (HSLA) Mg−Zn−Ca alloys. Acta Mater., 2015, 98, 423.

[40] Guan K, Ma R, Zhang JH, Wu RZ, Yang Q, Meng J. Modifying microstructures and tensile properties of Mg−Sm based alloy via extrusion ratio. J. Magnes. Alloys, 2021, 9(3): 1098.

[41] X.Z. Jin, W.C. Xu, D.B. Shan, B. Guo, and B.C. Jin, Mechanism of high-strength and ductility of Mg−RE alloy fabricated by low-temperature extrusion and aging treatment, Mater. Des., 199(2021), art. No. 109384.

[42] Agnew SR, Horton JA, Lillo TM, Brown DW. Enhanced ductility in strongly textured magnesium produced by equal channel angular processing. Scripta Mater., 2004, 50(3): 377.

[43] He C, Bai SW, Jiang B, et al. Effect of Gd content on the microstructure, texture and mechanical properties of Mg−xGd−0.5Mn alloys. J. Mater. Res. Technol., 2022, 20, 343.

[44] Li ZC, Yu JM, Lu DL, et al. Synergistic effects of grain refinement and texture weakening on mechanical properties anisotropy of Mg−9Gd−4Y−2Zn−0.4Zr alloy via RUE processing. J. Mater. Res. Technol., 2022, 19, 837.

[45] J.S. Wei, C.M. Liu, Y.C. Wan, J.B. Shao, X.Z. Han, and G.L. Zhang, Strengthening against $\{ 10\,\overline 1 \,2\} $ twinning by discontinuous and continuous precipitate in a strongly textured Mg−9Al alloy, Mater. Charact., 167(2020), art. No. 110523.

[46] Yang HB, Chai YF, Jiang B, et al. Enhanced mechanical properties of Mg−3Al−1Zn alloy sheets through slope extrusion. Int. J. Miner. Metall. Mater., 2022, 29(7): 1343.

[47] Wang QH, Shen YQ, Jiang B, et al. A good balance between ductility and stretch formability of dilute Mg−Sn−Y sheet at room temperature. Mater. Sci. Eng. A, 2018, 736, 404.

[48] Zhang L, Huang GS, Zhang H, Song B. Cold stamping formability of AZ31B magnesium alloy sheet undergoing repeated unidirectional bending process. J. Mater. Process. Technol., 2011, 211(4): 644.

[49] Dong JR, Zhang DF, Sun J, Dai QW, Pan FS. Effects of different stretching routes on microstructure and mechanical properties of AZ31B magnesium alloy sheets. J. Mater. Sci. Technol., 2015, 31(9): 935.

[50] Sanjari M, Farzadfar A, Kabir ASH, et al. Promotion of texture weakening in magnesium by alloying and thermomechanical processing: (I) alloying. J. Mater. Sci., 2014, 49(3): 1408.

[51] C. Ha, J. Bohlen, X. Zhou, et al., Texture development and dislocation activities in Mg−Nd and Mg−Ca alloy sheets, Mater. Charact., 175(2021), art. No. 111044.

[52] Chun YB, Davies CHJ. Investigation of prism <a> slip in warm-rolled AZ31 alloy. Metall. Mater. Trans. A, 2011, 42(13): 4113.