Achieving a high-strength dissimilar joint of T91 heat-resistant steel to 316L stainless steel via friction stir welding

Abstract

The reliable welding of T91 heat-resistant steel to 316L stainless steel is a considerable issue for ensuring the safety in service of ultra-supercritical power generation unit and nuclear fusion reactor, but the high-quality dissimilar joint of these two steels was difficult to be obtained by traditional fusion welding methods. Here we improved the structure—property synergy in a dissimilar joint of T91 steel to 316L steel via friction stir welding. A defect-free joint with a large bonding interface was produced using a small-sized tool under a relatively high welding speed. The bonding interface was involved in a mixing zone with both mechanical mixing and metallurgical bonding. No obvious material softening was detected in the joint except a negligible hardness decline of only HV ∼10 in the heat-affected zone of the T91 steel side due to the formation of ferrite phase. The welded joint exhibited an excellent ultimate tensile strength as high as that of the 316L parent metal and a greatly enhanced yield strength on account of the dependable bonding and material renovation in the weld zone. This work recommends a promising technique for producing high-strength weldments of dissimilar nuclear steels.

Keywords

heat-resistant steel / stainless steel / friction stir welding / dissimilar welding / microstructure / mechanical property

References

[1] Viswanathan R, Henry JF, Tanzosh J, et al. U.S. program on materials technology for ultra-supercritical coal power plants. J. Mater. Eng. Perform., 2005, 14(3): 281.

[2] Zinkle SJ, Was GS. Materials challenges in nuclear energy. Acta Mater., 2013, 61(3): 735.

[3] Zinkle SJ, Busby JT. Structural materials for fission & fusion energy. Mater. Today, 2009, 12(11): 12.

[4] Gong Y, Yang ZG, Yang FY. Heat strength evaluation and microstructures observation of the welded joints of one China-made T91 steel. J. Mater. Eng. Perform., 2012, 21(7): 1313.

[5] Ida M, Chida T, Furuya K, Wakai E, Nakamura H, Sugimoto M. Thermal-stress analysis of IFMIF target back-wall made of reduced-activation ferritic steel and austenitic stainless steel. J. Nucl. Mater., 2009, 386–388, 987.

[6] Zhou JH, Shen YF, Jia N. Strengthening mechanisms of reduced activation ferritic/martensitic steels: A review. Int. J. Miner. Metall. Mater., 2021, 28(3): 335.

[7] C. Li, X.D. Fang, Q.S. Wang, et al, A synergy of different corrosion failure modes pertaining to T91 steel impacted by extreme lead—bismuth eutectic flow pattern, Corros. Sci., 180(2021), art. No. 109214.

[8] C. Li, Y.J. Liu, F.F. Zhang, X.D. Fang, and Z. Liu, Erosion-corrosion of 304N austenitic steels in liquid PbBi flow perpendicular to steel surface, Mater. Charact., 175(2021), art. No. 111054.

[9] Zhang JY, Huang B, Wu QS, Li CJ, Huang QY. Effect of post-weld heat treatment on the mechanical properties of CLAM/316L dissimilar joint. Fusion Eng. Des., 2015, 100, 334.

[10] Vidyarthy RS, Kulkarni A, Dwivedi DK. Study of microstructure and mechanical property relationships of A-TIG welded P91—316L dissimilar steel joint. Mater. Sci. Eng. A, 2017, 695, 249.

[11] Albert SK, Das CR, Sam S, et al. Mechanical properties of similar and dissimilar weldments of RAFMS and AISI 316L (N) SS prepared by electron beam welding process. Fusion Eng. Des., 2014, 89(7–8): 1605.

[12] Serre I, Vogt JB. Mechanical properties of a 316L/T91 weld joint tested in lead-bismuth liquid. Mater. Des., 2009, 30(9): 3776.

[13] van den Bosch J, Almazouzi A. Compatibility of martensitic/austenitic steel welds with liquid lead bismuth eutectic environment. J. Nucl. Mater., 2009, 385(3): 504.

[14] Fu HY, Nagasaka T, Yamazaki M, et al. Deformation of dissimilar-metals joint between F82H and 316L in impact tests after neutron irradiation. Fusion Eng. Des., 2017, 124, 1063.

[15] Serizawa H, Mori D, Shirai Y, Ogiwara H, Mori H. Weldability of dissimilar joint between F82H and SUS316L under fiber laser welding. Fusion Eng. Des., 2013, 88(9–10): 2466.

[16] Serizawa H, Mori D, Ogiwara H, Mori H. Effect of laser beam position on mechanical properties of F82H/SUS316L butt-joint welded by fiber laser. Fusion Eng. Des., 2014, 89(7–8): 1764.

[17] Li Y, Zeng YP, Wang ZC. Interfacial microstructure evolution of 12Cr1MoV/TP347H dissimilar steel welded joints during aging. Int. J. Miner. Metall. Mater., 2021, 28(9): 1497.

[18] Sunilkumar D, Muthukumaran S, Vasudevan M, Reddy MG. Effect of friction stir and activated-GTA welding processes on the 9Cr—1Mo steel to 316LN stainless steel dissimilar weld joints. Sci. Technol. Weld. Join., 2020, 25(4): 311.

[19] Mishra RS, Ma ZY. Friction stir welding and processing. Mater. Sci. Eng. R, 2005, 50(1–2): 1.

[20] Ma ZY, Feng AH, Chen DL, Shen J. Recent advances in friction stir welding/processing of aluminum alloys: Microstructural evolution and mechanical properties. Crit. Rev. Solid State Mater. Sci., 2018, 43(4): 269.

[21] Shang Q, Ni DR, Xue P, Xiao BL, Ma ZY. Improving joint performance of friction stir welded wrought Mg alloy by controlling non-uniform deformation behavior. Mater. Sci. Eng. A, 2017, 707, 426.

[22] Han SC, Wu LH, Jiang CY, et al. Achieving a strong polypropylene/aluminum alloy friction spot joint via a surface laser processing pretreatment. J. Mater. Sci. Technol., 2020, 50, 103.

[23] Liu FC, Hovanski Y, Miles MP, Sorensen CD, Nelson TW. A review of friction stir welding of steels: Tool, material flow, microstructure, and properties. J. Mater. Sci. Technol., 2018, 34(1): 39.

[24] D.G. Mohan and C.S. Wu, A review on friction stir welding of steels, Chin. J. Mech. Eng., 34(2021), art. No. 137.

[25] He B, Cui L, Wang DP, Liu YC, Liu CX, Li HJ. The metallurgical bonding and high temperature tensile behaviors of 9Cr—1W steel and 316L steel dissimilar joint by friction stir welding. J. Manuf. Process., 2019, 44, 241.

[26] He B, Cui L, Wang DP, Li HJ, Liu CX. Microstructure and mechanical properties of RAFM—316L dissimilar joints by friction stir welding with different butt joining modes. Acta Metall. Sin. Engl. Lett., 2020, 33(1): 135.

[27] Tang WS, Yang XQ, Li SL, Li HJ. Microstructure and properties of CLAM/316L steel friction stir welded joints. J. Mater. Process. Technol., 2019, 271, 189.

[28] Zhang C, Cui L, Wang DP, Liu YC, Liu CX, Li HJ. The heterogeneous microstructure of heat affect zone and its effect on creep resistance for friction stir joints on 9Cr—1.5W heat resistant steel. Scripta. Mater., 2019, 158, 6.

[29] M. Türkan and Ö. Karakaş, Numerical modeling of defect formation in friction stir welding, Mater. Today Commun., 31(2022), art. No. 103539.

[30] Martín-Muñoz FJ, Soler-Crespo L, Gómez-Briceño D. Assessment of the influence of surface finishing and weld joints on the corrosion/oxidation behaviour of stainless steels in lead bismuth eutectic. J. Nucl. Mater., 2011, 416(1–2): 80.

[31] Wang ZW, Liu M, Zhang H, et al. Welding behavior of an ultrahigh-strength quenching and partitioning steel by fusion and solid-state welding methods. J. Mater. Res. Technol., 2022, 17, 1289.

[32] Wang ZW, Ma GN, Yu BH, et al. Improving mechanical properties of friction-stir-spot-welded advanced ultra-high-strength steel with additional water cooling. Sci. Technol. Weld. Joining, 2020, 25(4): 336.

[33] Sackl S, Clemens H, Primig S. Investigation of the self tempering effect of martensite by means of atom probe tomography. Pract. Metallogr., 2015, 52(7): 374.

[34] Wang ZW, Xie GM, Wang D, et al. Microstructural evolution and mechanical behavior of friction-stir-welded DP1180 advanced ultrahigh strength steel. Acta Metall. Sin. Engl. Lett., 2020, 33(1): 58.

[35] Shamanian M, Mirzaei A, Kangazian J, Szpunar JA. Characterization and mechanical behavior of AISI 316L/Incoloy 825 dissimilar welds processed by friction stir welding. J. Manuf. Process., 2020, 55, 66.

[36] Chen YC, Fujii H, Tsumura T, et al. Friction stir processing of 316L stainless steel plate. Sci. Technol. Weld. Joining, 2009, 14(3): 197.

[37] Park SHC, Sato YS, Kokawa H, Okamoto K, Hirano S, Inagaki M. Rapid formation of the sigma phase in 304 stainless steel during friction stir welding. Scripta. Mater., 2003, 49(12): 1175.

[38] Park SHC, Sato YS, Kokawa H, Okamoto K, Hirano S, Inagaki M. Corrosion resistance of friction stir welded 304 stainless steel. Scripta Mater., 2004, 51(2): 101.

[39] Wang ZW, Zhang JF, Xie GM, et al. Evolution mechanisms of microstructure and mechanical properties in a friction stir welded ultrahigh-strength quenching and partitioning steel. J. Mater. Sci. Technol., 2022, 102, 213.

[40] Zhu PC, Zhang L, Li ZC, et al. Microstructure and mechanical properties of friction stir welded 1.5 GPa martensitic high-strength steel plates. Acta Metall. Sin. Engl. Lett., 2022, 35(7): 1079.