Sliding wear behaviour of Fe/316L/430-Ti(C,N) composites prepared via spark plasma sintering and subsequent heat treatment

Abstract

A series of novel steel-Ti(C,N) composites was fabricated by spark plasma sintering (SPS) and subsequent heat treatment. The hardness, indentation fracture resistance, and wear behaviour of the steel-Ti(C,N) composites were compared with those of the unreinforced samples, and their potentials were assessed by comparison with traditional cermet/hardmetal systems. The results showed that with the addition of 20wt% Ti(C,N), the wear rates of the newly examined composites reduced by a factor of about 2 to 4 and were comparable to those of cermets and hardmetals. The martensitic transformation of the steel matrix and the formation of in situ carbides induced by heat treatment enhanced the wear resistance. Although the presence of excessive in situ carbides improved the hardness, the low indentation fracture resistance (IFR) value resulted in brittle fracture, which in turn resulted in poor wear property. Moreover, the operative wear mechanisms were investigated. This study provides a practical and cost-effective approach to prepare steel-Ti(C,N) composites as potential wear-resistant materials.

Keywords

iron-based composite / spark plasma sintering / heat treatment / titanium carbonitride / wear resistance

References

[1] Alvaredo P, Bruna P, Crespo D, Gordo E. Influence of carbon content on microstructure and properties of a steel matrix cermet. Int. J. Refract. Met. Hard Mater., 2018, 75, 78.

[2] Mojisola T, Ramakokovhu MM, Raethel J, Olubambi PA, Matizamhuka WR. In-situ synthesis and characterization of Fe-TiC based cermet produced from enhanced carbothermally reduced ilmenite. Int. J. Refract. Met. Hard Mater., 2019, 78, 92.

[3] Alvaredo P, Abajo C, Tsipas SA, Gordo E. Influence of heat treatment on the high temperature oxidation mechanisms of an Fe-TiCN cermet. J. Alloys Compd., 2014, 591, 72.

[4] Alvaredo P, Roa JJ, Jiménez-Pique E, Llanes L, Gordo E. Characterization of interfaces between TiCN and iron-base binders. Int. J. Refract. Met. Hard Mater., 2017, 63, 32.

[5] Chen M, Zhuang QM, Lin N, He YH. Improvement in microstructure and mechanical properties of Ti(C, N)-Fe cermets with the carbon additions. J. Alloys Compd., 2017, 701, 408.

[6] Wang Z, Lin T, He XB, Shao HP, Zheng JS, Qu XH. Microstructure and properties of TiC-high manganese steel cermet prepared by different sintering processes. J. Alloys Compd., 2015, 650, 918.

[7] Li GP, Jia JX, Lyu YH, Zhao JZ, Lu J, Li YM, Luo FH. Effect of Mo addition mode on the microstructure and mechanical properties of TiC-high Mn steel cermets. Ceram. Int., 2020, 46(5): 5745.

[8] Liu SF, Liu DC. Effect of hard phase content on the mechanical properties of TiC-316L stainless steel cermets. Int. J. Refract. Met. Hard Mater., 2019, 82, 273.

[9] Lin T, Guo Y, Wang Z, Shao HP, Lu HY, Li FH, He XB. Effects of chromium and carbon content on micro-structure and properties of TiC-steel composites. Int. J. Refract. Met. Hard Mater., 2018, 72, 228.

[10] Jin CX, Plucknett KP. Microstructure instability in TiC-316L stainless steel cermets. Int. J. Refract. Met. Hard Mater., 2016, 58, 74.

[11] Olejnik E, Szymański Ł, Tokarski T, Opitek B, Kurtyka P. Local composite reinforcements of TiC/FeMn type obtained in situ in steel castings. Arch. Civ. Mech. Eng., 2019, 19(4): 997.

[12] Olejnik E, Tokarski T, Sikora G, Sobula S, Maziarz W, Szymański Ł, Grabowska B. The effect of Fe addition on fragmentation phenomena, macrostructure, microstructure, and hardness of TiC-Fe local reinforcements fabricated in situ in steel casting. Metall. Mater. Trans. A, 2019, 50(2): 975.

[13] Rahimipour MR, Sobhani M. Evaluation of centrifugal casting process parameters for in situ fabricated functionally gradient Fe-TiC composite. Metall. Mater. Trans. B, 2013, 44(5): 1120.

[14] Wang Y, Zou BL, Cao XQ. Combustion synthesis of TiC-TiB₂ particulates locally reinforced steel matrix composites from an Al-Ti-B₄C system during casting. Acta Metall. Sinica, 2014, 50(3): 367.

[15] Shankar E, Prabu SB. Influence of WC and cobalt additions on the microstructural and mechanical properties of TiCN-Cr₃C₂-nano-TiB₂ cermets fabricated by spark plasma sintering. Int. J. Refract. Met. Hard Mater., 2017, 69, 110.

[16] Lancaster JK. The influence of substrate hardness on the formation and endurance of molybdenum disulphide films. Wear, 1967, 10(2): 103.

[17] Wu RM, Li W, Zhou S, Zhong Y, Wang L, Jin XJ. Effect of retained austenite on the fracture toughness of quenching and partitioning (Q&P)-treated sheet steels. Metall. Mater. Trans. A, 2014, 45(4): 1892.

[18] Ikeda M, Umeda T, Tong CP, Suzuki T, Niwa N, Kato O. Effect of molybdenum addition on solidification structure, mechanical properties and wear resistivity of high chromium cast irons. ISIJ Int., 1992, 32(11): 1157.

[19] Kumar BVM, Basu B, Kalin M, Vizintin J. Load-dependent transition in sliding wear properties of Ti(C,N)-WC-Ni cermets. J. Am. Ceram. Soc., 2007, 90(5): 1534.

[20] Taktak Ş, Başpınar MS. Observation of delamination wear of lubricious tribofilm formed on Si₃N₄ during sliding against WC-Co in humidity air. Tribol. Int., 2006, 39(1): 39.

[21] Zhang H, Wang XH, Liu MY, Fang XM. Reciprocating wear performance and interfacial microstructure of a TiC-Ni₂AlTi cermet. Tribol. Lett., 2014, 55(2): 211.

[22] Filipović MM. Iron-chromium-carbon-vanadium white cast irons: Microstructure and properties. Hem. Ind., 2014, 68(4): 413.

[23] Onuoha CC, Kipouros GJ, Farhat ZN, Plucknett KP. The reciprocating wear behaviour of TiC-304L stainless steel composites prepared by melt infiltration. Wear, 2013, 303(1–2): 321.

[24] Stewart TL, Plucknett KP. The sliding wear of TiC and Ti(C,N) cermets prepared with a stoichiometric Ni₃Al binder. Wear, 2014, 318(1–2): 153.

[25] Stott FH, Wood GC. The influence of oxides on the friction and wear of alloys. Tribol. Int., 1978, 11(4): 211.

[26] Pirso J, Viljus M, Letunovitš S. Friction and dry sliding wear behavior of cermets. Wear, 2006, 260(7–8): 815.