Mechanical properties and wear resistance of ultrafine bainitic steel under low austempering temperature

Abstract

The mechanical properties and wear resistance of the ultrafine bainitic steel austempered at various temperatures were investigated. Scanning electron microscopy (SEM) and X-ray diffraction were used to analyze the microstructure. The worn surfaces were observed via laser scanning confocal microscopy and SEM. Results indicated that, under low austempering temperatures, the mechanical properties differed, and the wear resistance remained basically unchanged. The tensile strength of the samples was above 1800 MPa, but only one sample austempered at 230°C had an elongation of more than 10%. The weight loss of samples was approximately linear with the cycles of wear and nonlinear with the loads. The samples showed little difference in wear resistance at different isothermal temperatures, whereas the thickness of their deformed layers varied greatly. The results are related to the initial hardness of the sample and the stability of the retained austenite. Meanwhile, the experimental results showed that the effect of austempering temperature on the wear resistance of ultrafine bainitic steel can be neglected under low applied loads and low austempering temperature.

Keywords

bainitic steel / mechanical properties / wear resistance / austempering temperature

References

[1] Caballero FG, Bhadeshia HKDH, Mawella KJA, Jones DG, Brown P. Very strong low temperature bainite. Meter. Sci. Technol, 2002, 18, 279.

[2] Hu ZW, Xu G, Hu HJ, Wang L, Xue ZL. In situ measured growth rates of bainite plates in an Fe-C-Mn-Si superbainitic steel. Int. J. Miner. Metall. Mater, 2014, 21, 371.

[3] Fan HL, Zhao AM, Li QC, Guo H, He JG. Effects of ausforming strain on bainite transformation in nanostructured bainite steel. Int. J. Miner. Metall. Mater, 2017, 24, 264.

[4] Behzad A. Effect of prolonged isothermal heat treatment on the mechanical behavior of advanced NANOBAIN steel. Int. J. Miner. Metall. Mater, 2017, 24, 1010.

[5] Zhao J, Guo K, He YM, Wang YF, Wang TS. Extremely high strength achievement in medium-C nanobainite steel. Scripta Mater., 2018, 152, 20..

[6] He JG, Zhao AM, Zhi C, Fan HL. Acceleration of nanobainite transformation by multi-step ausforming process. Scripta Mater, 2015, 107, 71.

[7] Guo H, Feng XY, Zhao AM, Li Q, Ma J. Influence of prior martensite on bainite transformation, micro-structures, and mechanical properties in ultra-fine bainitic steel. Materials, 2019, 12, 527.

[8] Kumar A, Singh A. Toughness dependence of nanobainite on phase fraction and morphology. Mater. Sci. Eng. A, 2018, 729, 439.

[9] Yoozbashi MN, Yazdani S, Wang TS. Design of a new nanostructured, high-Si bainitic steel with lower cost production. Mater. Des., 2011, 32, 3248.

[10] Lu XH, Qian DS, Li W, Jin XJ. Enhanced toughness of bearing steel by combining prior cold deformation with martensite pre-quenching and bainite transformation. Mater. Lett, 2019, 234, 5.

[11] Guo H, Zhao AM, Zhi C, Ding R, Wang JX. Two-body abrasion wear mechanism of super bainitic steel. Mater. Sci. Technol, 2017, 33, 893.

[12] Efremenkoa VG, Hesse O, Friedrich T, Kunert M, Brykov MN, Shimizu K, Zurnadzhy VI, Šuchmann P. Two-body abrasion resistance of high-carbon high-silicon steel: Metastable austenite vs nanostructured bainite. Wear, 2019, 418-419, 24.

[13] Das Bakshi S, Shipway PH, Bhadeshia HKDH. Three-body abrasive wear of fine pearlite, nanostructured bainite and martensite. Wear, 2013, 308, 46.

[14] Shah M, Das Bakshi S. Three-body abrasive wear of carbide-free bainite, martensite and bainite-martensite structure of similar hardness. Wear, 2018, 402-403, 207.

[15] Wang TS, Yang J, Shang CJ, Li XY, Lv B, Zhang M, Zhang FC. Sliding friction surface microstructure and wear resistance of 9SiCr steel with low-temperature aus-tempering treatment. Surf. Coat. Technol., 2008, 202, 4036.

[16] Hasan SM, Chakrabarti D, Singh SB. Dry rolling/sliding wear behaviour of pearlitic rail and newly developed carbide-free bainitic rail steels. Wea, 2018, 408-409, 151.

[17] Das Bakshi S, Leiro A, Prakash B, Bhadeshia HKDH. Dry rolling/sliding wear of nanostructured bainite. Wear, 2014, 316, 70-78.

[18] Rementeria R, García I, Aranda MM, Caballero FG. Reciprocating-sliding wear behavior of nanostructured and ultra-fine high-silicon bainitic steels. Wear, 2015, 338-339, 202.

[19] Singh K, Singh A. Tribological response and micro-structural evolution of nanostructured bainitic steel under repeated frictional sliding. Wear, 2018, 410-411, 63.

[20] Long XY, Zhang FC, Kang J, Yang ZN, Wu DD, Wu KM, Zhang GH. Study on carbide-bearing and carbide-free bainitic steels and their wear resistance. Mater. Sci. Technol, 2017, 33, 615.

[21] De AK, Murdock DC, Mataya MC, Speer JG, Matlock DK. Quantitative measurement of deformation-induced martensite in 304 stainless steel by X-ray diffraction. Scripta Mater, 2004, 50, 1445.

[22] Bhadeshia HKDH, Edmonds DV. Bainite in silicon steels: New composition-property approach Part 1. Met Sci., 1983, 17, 411.

[23] Kozeschnik E, Bhadeshia HKDH. Influence of silicon on cementite precipitation in steels. Mater. Sci. Technol, 2008, 24, 343.

[24] Chang LC, Bhadeshia HKDH. Austenite films in bainitic microstructures. Mater. Sci. Technol., 1995, 11, 874.

[25] Garcia-Mateo C, Caballero FG, Sourmail T, Kuntz M, Cornide J, Smanio V, Elvira R. Tensile behaviour of a nanocrystalline bainitic steel containing 3wt% silicon. Mater. Sci. Eng. A, 2012, 549, 185.

[26] Garcia-Mateo C, Caballero FG, Bhadeshia HKDH. Acceleration of low-temperature bainite. ISIJ Int., 2003, 43, 1821.

[27] Avishan B, Tavakolian M, Yazdani S. Two-step aus-tempering of high performance steel with nanoscale micro-structure. Mater. Sci. Eng. A, 2017, 693, 178.

[28] Chiang J, Lawrence B, Boyd JD, Pilkey AK. Effect of microstructure on retained austenite stability and work hardening of TRIP steels. Mater. Sci. Eng. A, 2011, 528, 4516.

[29] Narayanaswamy B, Hodgson P, Timokhina I, Beladi H. The impact of retained austenite characteristics on the two-body abrasive wear behavior of ultrahigh strength bainitic steels. Metall. Mater. Trans. A, 2016, 47, 4883.

[30] Larsen-Basse J. Role of microstructure and mechanical properties in abrasion. Scripta Metall. Mater, 1990, 24, 821.

[31] Sun T, Song RB, Yang FQ, Wu CJ. Wear behavior of bainite ductile cast iron under impact load. Int. J. Miner. Metall. Mater, 2014, 21, 871.

[32] Bhadeshia HKDH. Steels for bearings. Prog. Mater. Sci., 2012, 57, 268.

[33] Liu BG, Li W, Lu XW, Jia XS, Jin XJ. The effect of retained austenite stability on impact-abrasion wear resistance in carbide-free bainitic steels. Wear, 2019, 428-429, 127.