Simulation of macrosegregation in a 36-t steel ingot using a multiphase model

Abstract

Macrosegregation is the major defect in large steel ingots caused by solute partitioning and melt convection during casting. In this study, a three-phase (liquid, columnar dendrites, and equiaxed grains) model is proposed to simulate macrosegregation in a 36-t steel ingot. A supplementary set of conservation equations are employed in the model such that two types of equiaxed grains, either settling or adhering to the solid shell, are well simulated. The predicted concentration agrees quantitatively with the experimental value. A negative segregation cone was located at the bottom owing to the grain settlement and solute-enriched melt leaving from the mushy zone. The interdendritic liquid flow was carefully analyzed, and the formation of A-type segregations in the mid-height of the ingot is discussed. Negative segregation was observed near the riser neck due to the specific relationship between flow direction and temperature gradient. Additionally, the as-cast macrostructure of the ingot is presented, including the grain size distribution and columnar-equiaxed transition.

Keywords

macrosegregation / multiphase model / transportation / solidification / steel ingot

References

[1] Pickering EJ. Macrosegregation in steel ingots: The applicability of modelling and characterization techniques. ISIJ Int., 2013, 53(6): 935.

[2] Flemings MC. Our understanding of macrosegregation: Past and present. ISIJ Int., 2000, 40(9): 833.

[3] Prakash C. Two-phase model for binary solid-liquid phase change, Part I: governing equations. Numer. Heat Transfer Part B, 1990, 18, 131.

[4] Ni J, Beckermann C. A volume-averaged two-phase model for transport phenomena during solidification. Metall. Trans. B, 1991, 22(3): 349.

[5] Ludwig A, Wu MH. Modeling the columnar-to-equiaxed transition with a three-phase Eulerian approach. Mater. Sci. Eng. A, 2005, 413–414, 109.

[6] Combeau H, Založnik M, Hans S, Richy PE. Prediction of macrosegregation in steel ingots: Influence of the motion and the morphology of equiaxed grains. Metall. Mater. Trans. B, 2009, 40(3): 289.

[7] Wu M, Fjeld A, Ludwig A. Modelling mixed columnar-equiaxed solidification with melt convection and grain sedimentation-Part I: Model description. Comput. Mater. Sci., 2010, 50(1): 32.

[8] Wu M, Fjeld A, Ludwig A. Modelling mixed columnar—equiaxed solidification with melt convection and grain sedimentation—Part II: Illustrative modelling results and parameter studies. Comput. Mater. Sci., 2010, 50(1): 43.

[9] Wu M, Ludwig A, Kharicha A. A four phase model for the macrosegregation and shrinkage cavity during solidification of steel ingot. Appl. Math. Modell., 2017, 41, 102.

[10] Duan ZH, Tu WT, Shen BZ, Shen HF, Liu BC. Experimental measurements for numerical simulation of macrosegregation in a 36-ton steel ingot. Metall. Mater. Trans. A, 2016, 47(7): 3597.

[11] Tu WT, Duan ZH, Shen BZ, Shen HF, Liu BC. Three-dimensional simulation of macrosegregation in a 36-ton steel ingot using a multicomponent multiphase model. JOM, 2016, 68(12): 3116.

[12] Wu Menghuai, Ludwig Andreas, Kharicha Abdellah. Simulation of As-Cast Steel Ingots. steel research international, 2017, 89(1): 1700037.

[13] Li WS, Shen HF, Liu BC. Numerical simulation of macrosegregation in steel ingots using a two-phase model. Int. J. Miner. Metall. Mater., 2012, 19(9): 787.

[14] Tu WT, Shen HF, Liu BC. Two-phase modeling of macrosegregation in a 231t steel ingot. ISIJ Int., 2014, 54(2): 351.

[15] Ludwig A, Wu MH. Modeling of globular equiaxed solidification with a two-phase approach. Metall. Mater. Trans. A, 2002, 33(12): 3673.

[16] Hunt JD. Steady state columnar and equiaxed growth of dendrites and eutectic. Mater. Sci. Eng., 1984, 65(1): 75.