Effect of Ca modification on the elemental composition, microstructure and tensile properties of Al-7Si-0.3Mg alloy

Abstract

The effect of Ca addition on the elemental composition, microstructure, Brinell hardness and tensile properties of Al-7Si-0.3Mg alloy were investigated. The residual content of Ca in the alloy linearly increased with the amount of Ca added to the melt. The optimal microstructure and properties were obtained by adding 0.06wt% Ca to Al-7Si-0.3Mg alloy. The secondary dendrite arm spacing (SDAS) of the primary α phase decreased from 44.41 μm to 19.4 μm, and the eutectic Si changed from coarse plates to fine coral. The length of the Fe-rich phase (β-Al₅FeSi) decreased from 30.2 μm to 3.8 um, and the Brinell hardness can reach to 66.9. The ultimate tensile strength, yield strength, and elongation of the resulting alloy increased from 159.5 MPa, 79 MPa, and 2.5% to 212 MPa, 86.5 MPa, and 4.5%, respectively. The addition of Ca can effectively refine the primary α phase and modify the eutectic Si phase, likely because Ca enrichment at the front of the solid-liquid interface led to undercooling of the alloy, reduced the growth rate of the primary α phase, and refined the grain size. Also, it could increase the latent heat of crystallization, undercooling, and the nucleation rate of eutectic Si, which was beneficial to the improvement of the morphology of eutectic Si.

Keywords

Ca / Al-Si-Mg alloy / microstructure / mechanical properties

References

[1] Elgallad EM, Ibrahim MF, Doty HW, Samuel FH. Microstructural characterisation of Al-Si cast alloys containing rare earth additions. Philos. Mag., 2018, 98, 1337.

[2] Roehling JD, Coughlin DR, Gibbs JW, Baldwin JK, Mertens JCE, Campbell GH, Clarke AJ, Mckeown JT. Rapid solidification growth mode transitions in Al-Si alloys by dynamic transmission electron microscopy. Acta Mater., 2017, 131, 22.

[3] Qiao JG, Liu XF, Liu XJ, Bian XF. Relationship between microstructures and contents of Ca/P in near-eutectic Al-Si piston alloys. Mater. Lett., 2005, 59, 1790.

[4] Kumari SSS, Pillai RM, Pai BC, Nogita K, Dahle AK. Influence of calcium on the microstructure and properties of an Al-7Si-0.3Mg-xFe Alloy. Metall. Mater. Trans. A, 2006, 37, 2581.

[5] Kumari SSS, Pillai RM, Pai BC. Role of calcium in aluminium based alloys and composites. Int. Metall. Rev., 2013, 50, 216.

[6] Al-Helal K, Wang Y, Stone I, Fan ZY. Effect of Ca level on the formation of silicon phases during solidification of hypereutectic Al-Si alloys. Mater. Sci. Forum, 2013, 765, 117.

[7] Kim HJ. Effect of calcium on primary silicon particle size in hypereutectic Al-Si alloys. Mater. Sci. Technol, 2003, 19, 915.

[8] Kumari SSS, Pillai RM, Rajan TPD, Pai BC. Effects of individual and combined additions of Be, Mn, Ca and Sr on the solidification behaviour, structure and mechanical properties of Al-7Si-0.3Mg-0.8Fe alloy. Mater. Sci. Eng. A, 2007, 461, 561.

[9] Knuutinen A, Nogita K, McDonald SD, Dahle AK. Modification of Al-Si alloys with Ba, Ca, Y and Yb. J. Light Met, 2001, 1, 229.

[10] Ludwig TH, Schaffer PL, Arnberg L. Influence of some trace elements on solidification path and microstructure of Al-Si foundry alloys. Metall. Mater. Trans. A, 2013, 44, 3783.

[11] Ceschini L, Morri A, Morri A, Gamberini A, Mes-sieri S. Correlation between ultimate tensile strength and solidification microstructure for the sand cast A357 aluminium alloy. Mater. Des., 2009, 30, 4525.

[12] Zhang J, Fan Z, Wang YQ, Zhou BL. Effect of cooling rate on the microstructure of hypereutectic Al-Mg₂Si alloys. J. Mater. Sci. Lett., 2000, 19, 1825.

[13] Eidhed W. Modification of P-Al5FeSi compound in recycled Al-Si-Fe cast alloy by using Sr, Mg and Cr additions. J. Mater. Sci. Technol, 2008, 24, 45.

[14] Mican S, Hirian R, Isnard O, Chicinaş I, Pop V. Effect of milling conditions on the microstructure and interphase exchange coupling of Nd₂Fe₁₄B/nanocomposites. Phys. Procedia, 2015, 75, 1314.

[15] Tang P, Li WF, Wang K, Du J, Chen XY, Zhao YJ, Li WZ. Effect of Al-Ti-C master alloy addition on micro-structures and mechanical properties of cast eutectic Al-Si-Fe-Cu alloy. Mater. Des., 2017, 115, 147.

[16] Kobayashi T. Strength and fracture of aluminum alloys. Mater. Sci. Eng. A, 2000, 286, 333.

[17] Li C, Liu XF, Wu YY. Refinement and modification performance of Al-P master alloy on primary Mg₂Si in Al-Si-Mg alloys. J. Alloys Compd., 2008, 465, 145.