Effects of conform continuous extrusion and heat treatment on the microstructure and mechanical properties of Al–13Si–7.5Cu–1Mg alloy

Abstract

The effects of conform continuous extrusion and subsequent heat treatment on the mechanical and wear-resistance properties of high-alloying Al–13Si–7.5Cu–1Mg alloy were investigated. The microstructures of alloys before and after conform processing and aging were compared by transmission electron microscopy and scanning electron microscopy, respectively. The results reveal that the primary phases were broken and refined by intense shear deformation during conform processing. After the conform-prepared Al–13Si–7.5Cu–1Mg alloy was subjected to solid-solution treatment at 494°C for 1.5 h and aging at 180°C for 4 h, its hardness improved from HBS 115.8 to HBS 152.5 and its ultimate tensile strength increased from 112.6 to 486.8 MPa. Its wear resistance was also enhanced. The factors leading to the enhanced strength, hardness, and wear resistance of the alloy were discussed in detail.

Keywords

Al–13Si–7.5Cu–1Mg alloy / conform continuous extrusion / heat treatment / wear resistance

References

[1] Xu FT, Xu Y, Li G. The mechanism of PEO process on Al–Si alloys with the bulk primary silicon. Appl. Surf. Sci., 2009, 255(23): 9531.

[2] Zamani M, Seifeddine S. Determination of optimum Sr level for eutectic Si modification in Al–Si cast alloys using thermal analysis and tensile properties. Int. J. Metalcast., 2016, 10(4): 457.

[3] Cepeda-Jiménez CM, Orozco-Caballero A, García-Infanta JM, Zhilyaev AP, Ruano OA, Carrenoa F. Assessment of homogeneity of the shear-strain pattern in Al–7wt%Si casting alloy processed by high-pressure torsion. Mater. Sci. Eng. A, 2014, 597, 102.

[4] Li Z, Samuel AM, Samuel FH, Ravindran C, Valtierra S, Doty HW. Parameters controlling the performance of AA319-type alloys: Part I. Tensile properties. Mater. Sci. Eng. A, 2004, 367(1–2): 96.

[5] He KZ, Yu FX, Zhao DZ, Zuo L. Characterization of precipitates in a hot-deformed hypereutectic Al–Si alloy. J. Alloys Compd., 2012, 539, 74.

[6] Zuo L, Yu FX. DC Casting, Deformation and Strengthening of Al–Si Alloys. Mater. Sci. Forum, 2012, 706–709, 186.

[7] Chen HB, Yang B. Effect of heat treatment on microstructures and mechanical properties of a bulk nanostructured Al–Zn–Mg–Cu alloy. Int. J. Miner. Metall. Mater., 2009, 16(16): 672.

[8] Xu C, Schroeder S, Berbon PB, Langdon TG. Principles of ECAP-Conform as a continuous process for achieving grain refinement: Application to an aluminum alloy. Acta Mater., 2010, 58(4): 1379.

[9] Murashkin M, Medvedev A, Kazykhanov V, Krokhin A, Raab G, Enikeev N, Valive RZ. Enhanced mechanical properties and electrical conductivity in ultrafine-grained Al 6101 alloy processed via ECAP-Conform. Metals, 2015, 5(4): 2148.

[10] Zhang H, Jiang FL, Shang XY, Li LX. Flow stress and microstructural evolution of the horizontal continuous casting Al–0.96Mn–0.38Si–0.18Fe alloy during hot compression. Mater. Sci. Eng. A, 2013, 571, 25.

[11] Zhang XY, Zhang H, Kong XX, Fu DF. Microstructure and properties of Al–0.70Fe–0.24Cu alloy conductor prepared by horizontal continuous casting and subsequent continuous extrusion forming. Trans. Nonferrous. Met. Soc. China, 2015, 25(6): 1763.

[12] Pardoe JA. Conform continuous extrusion process — its contribution to energy conservation. Met. Technol., 1984, 11(1): 358.

[13] Lasa L, Rodriguez-Ibabe JM. Evolution of the main intermetallic phases in Al–Si–Cu–Mg casting alloys during solution treatment. J. Mater. Sci., 2004, 39(4): 1343.

[14] Sjölander E, Seifeddine S. The heat treatment of Al–Si–Cu–Mg casting alloys. J. Mater. Process. Technol., 2010, 210, 1249.

[15] Moustafa MA, Samuel FH, Doty HW, Valtierra S. Effect of Mg and Cu additions on the microstructural characteristics and tensile properties of Sr-modified Al–Si eutectic alloys. Int. J. Cast Met. Res., 2002, 14(4): 235.

[16] Raghukiran N, Kumar R. Effect of scandium addition on the microstructure, mechanical and wear properties of the spray formed hypereutectic aluminum-silicon alloys. Mater. Sci. Eng. A, 2015, 641, 138.

[17] Chaudhury SK, Apelian D. Fluidized bed heat treatment of cast Al–Si–Cu–Mg alloys. Metall. Mater. Trans. A, 2006, 37, 2295.

[18] Kang N, Coddet P, Liao HL, Baur T, Coddet C. Wear behavior and microstructure of hypereutectic Al–Si alloys prepared by selective laser melting. Appl. Surf. Sci., 2016, 378, 142.

[19] Li RX, Li RD, Zhao YH, He LZ, Li CX, Guan HR, Hu ZQ. Age-hardening behavior of cast Al–Si base alloy. Mater. Lett., 2004, 58(15): 2096.

[20] Pan X, Morral JE, Brody HD. Predicting the Q-phase in Al–Cu–Mg–Si alloys. J. Phase Equilib. Diffus., 2010, 31(2): 144.

[21] Chakrabarti DJ, Laughlin DE. Phase relations and precipitation in Al–Mg–Si alloys with Cu additions. Prog. Mater. Sci., 2004, 49(3–4): 389.

[22] Farkoosh AR, Pekguleryuz M. Enhanced mechanical properties of an Al–Si–Cu–Mg alloy at 300°C: Effects of Mg and the Q-precipitate phase. Mater. Sci. Eng. A, 2015, 621, 277.

[23] Gazizov M, Kaibyshev R. Effect of pre-straining on the aging behavior and mechanical properties of an Al–Cu–Mg–Ag alloy. Mater. Sci. Eng. A, 2015, 625, 119.